• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1995년도 하계학술대회 논문집 C
• /
• pp.1394-1397
• /
• 1995

In the hazardous areas where explosive gases, vapor or mists exist, electrical apparatus and installations must be of explosion-proof construction to prevent or limit the danger of the ignition of potentially explosive atmosphere. In Korea, nine types of protection have been specified in the government regulations at present: flameproof enclosure, pressurization, oil immersion, increased safety, intrinsic safety, non-incendive, sand filling, encapsulation, and special types. Among these types, the intrinsic safety has the construction which limit or by-pass igniting the electric energy using electronic devices. This type has lots of merits but at the same time requires a high-degree of technology. In this paper, we investigated several dominating factors which affect the minimum ignition energy: this energy plays a very important role in design and evaluation of the intrinsic safety type electrical apparatus. Eletrode material, which is one of the most important factors, was intensively studied for the five sorts of material(Al, Cd, Mg, Sn, and Zn) with performing experiment in a low-voltage inductive circuit using IEC-type spark apparatus. The experimental results show that the minimum ignition energy of electrode material is varied: highest in Cd and lowest in Sn. We also confirmed the effect of eletrode make-and-break speed and magnetic field magnitude.

• 한국안전학회지
• /
• 제25권5호
• /
• pp.22-26
• /
• 2010

The ignitability(minimum ignition energy, MIE) of a suspended dust clouds is very important aspect of technical safety indices. This paper reported the experimental results dealing with the influence of discharge circuit on the MIE of a suspended dust clouds. The movement of a suspended dust clouds was also observed with the high speed camera. The Hartmann vertical-tube apparatus(MIKE-3) described in the international standard of IEC and Polypropylene (PP, 50% volume-average, D50: $761{\mu}m$) resin powders were used in this experiment. The following results were obtained: (1) the MIE of a suspended PP powder depended markedly on the discharge circuit; in other words, when a resistor was connected in series with the discharge sparking circuit(RC), the lowest value(31mJ) of MIE was obtained for a suspended PP powder comparison with the other circuits(C circuit; 370mJ or LC circuit; 71mJ). (2) the discharge duration time is more important than other factors with regard to MIE of a suspended PP powder.

• 한국안전학회지
• /
• 제22권1호
• /
• pp.36-39
• /
• 2007

It is important to know Minimum Ignition Energy(MIE) of flammable materials for ignition hazard of chemical processes etc.. Currently a capacitor discharge is used mainly to measure the MIE. Then, it is impossible to control actively discharge energies and discharge time because the MIE measurement uses a high voltage capacitor and fixed capacitor. However, the control of discharge energy and discharge time will be convenient if self-sustain discharge is used. In this paper, we measured the MIE by self-sustain discharge of a pulse shape to propose the new measuring method of the MIE. AS a result, ignition energies are increased gradually as discharge duration time gets longer, and discharge current grows larger. Also, an arc discharge and a glow discharge occurred during the experimental period, and the ignition by glow discharges happened when discharge duration time was $90{\mu}s$, discharge current was 8A and 1A Especially, the MIE occurred the 0.05mm and 0.08mm of the gap distance between discharge electrode in the same discharge duration time.

• 대한화학회지
• /
• 제8권2호
• /
• pp.57-61
• /
• 1964

It was verified at Part Ⅰ of this investigation that there is a minimum wettability between molten iron and graphite, which was preliminarily coated with magnesium, and thus the spheroidization of graphite might have resulted from the lack of wettability between magnesium-adsorbed graphite and iron matrix. Being continued from the last work, the wettability between pure iron and graphite, coated with the various thickness of cerium, are measured at melting point of pure iron in vacuum and 200 mmHg argon gas atmosphere. The result indicates the presence of a minimum wettability at a critical thickness of cerium film as was proved in the case of magnesium. The experimental analysis shows that, the minimum wettability could be attributed entirely to a minimum work of adhesion between liquid iron and graphite at a critical concentration of cerium in the iron-graphite interface.

• 한국정보통신학회논문지
• /
• 제21권4호
• /
• pp.688-697
• /
• 2017

비선형 시스템의 이동 로봇을 원하는 목표점으로 속도, 가속도 그리고 각속도 관련 에너지를 최소한으로 사용하여 최단시간 안에 이동시키는 최적의 제어 문제를 수학적으로 푸는 것이 매우 어렵다. 본 논문에서는 유전알고리즘을 이용하여 이동 로봇의 속도, 각속도 관련 에너지를 최소화하면서 최단시간 안에 이동할 수 있는 최적제어이득을 구한다. 이동 로봇은 비선형시스템이므로 초기위치에 따라 최적제어이득이 다르게 결정된다. 따라서 초기위치 분할 점들을 설정하고 각 분할 점에서 유전알고리즘을 이용하여 최적제어이득을 구한다. 각 분할 점에서 구한 최적제어 이득으로 신경회로망을 학습시켜서 임의의 초기위치에 대한 제어이득을 구할 수 있다. 마지막으로 본 연구의 유용성을 컴퓨터 시뮬레이션 연구로 확인한다.

• 한국통신학회논문지
• /
• 제35권5A호
• /
• pp.466-473
• /
• 2010

에너지 효율성과 같은 센서 네트워크에 중요한 요소들을 보장하기 위한 트리기반 프로토콜들이 여럿 제시되었다. 하지만 선박이나 해양 분야와 같이 베이스 노드의 이동성이 큰 네트워크 환경을 전제로 한 토폴로지에 대한 연구는 부족하였다. 본 논문에서는 베이스 노드의 이동성이 큰 센서 네트워크 환경에 적합한 토폴로지로 최소 Wiener 수 신장트리를 제안한다. 가중치 있는 그래프로부터 최소 Wiener 수를 가진 신장트리를 구하는 문제는 NP-hard로 알려져 있다. 문제 해결을 위해 분기 한정 알고리즘을 설계하고 대표적인 신장트리 중 하나인 최소신장트리를 대상으로 1라운드 패킷 전송에 필요한 전송 거리 및 에너지 소모량, 네트워크 수명을 모의실험을 통해 비교하였다. 전송 거리와 에너지 소모량은 제시한 트리가 최소신장트리에 비해 우수하였지만 네트워크 수명은 오히려 열등함을 알 수 있었다.

• 한국진공학회지
• /
• 제8권2호
• /
• pp.102-110
• /
• 1999

The LIGA X-ray exposure step was modelled into three inequalities, by assuming that the X-ray energy attenuated within a resist is deposited only in the localized range of the resist. From these inequalities, equations for the minimum and maximum exposure times required for a good quality microstructure were obtained. Also, an equation for the thickness of an X-ray mask absorber was obtained from the exposure requirement of threshold dose deposition. The calculation method of the synchrotron radiation power from a synchrotron radiation source was introduced and applied to an X-ray exposure step. A power from a synchrotron radiation source was introduced and applied to an X-ray exposure step/ A power function of photon energy, approximating the attenuation length of the representative LIGA resist, PMMA, and the mean photon energy of the XZ-rays incident upon an X-ray mask absorber were applied to the above mentioned equations. Consequently, the tendencies of the minimum and maximum exposure and with respect to mean photon energy and thick ness of PMMA was obtained. Additionally, the tendencies of the necessary thickness of PMMA and photon energy of the X-ray mask absorber with respect to thickness of PMMA and photon energy of the X-rays incident upon an X-ray mask absorber were examined. The minimum exposure time increases monotonically with increasing mean photon energy for the same total power density and is not a function of the thickness of resist. The minimum exposure time increases with increasing mean photon energy for the same total power density in the case of the general LIGA process, where the thickness of PMMA is thinner than the attenuation length of PMMA. Additionally, the minimum exposure time increases monotonically with increasing thickness of PMMA. The maximally exposable thickness of resist is proportional to the attenuation length of the resist at the mean photon energy with its proportional constant of ln $(Dd_m/D_{dv})$. The necessary thickness of a gold X-ray mask absorber due to absorption edges of gold, increases smoothly with increasing PMMA thickness ratio, and is independent of the total power density itself. The simplicity of the derived equations has made clearly understandable the X-ray exposure phenomenon and the correlation among the exposure times, the attenuation coefficient and the thickness of an X-ray mask absorber, the attenuation coefficient and the thickness of the resist, and the synchrotron radiation power density.

• 한국방사성폐기물학회:학술대회논문집
• /
• 한국방사성폐기물학회 2018년도 춘계학술논문요약집
• /
• pp.379-380
• /
• 2018

• 한국태양에너지학회:학술대회논문집
• /
• 한국태양에너지학회 2008년도 추계학술발표대회 논문집
• /
• pp.63-68
• /
• 2008

Efforts tp overcome the current challenge of global warming and abnormal temperature are being taken around the world. According to a report, average temperature of Korea has increased by about $0.8^{\circ}C$ for a century. In particular, temperature has rapidly increased since year 2000. Climate changes have brought remarkable changes in our lives. For example, agricultural field will see changes in crops and production. Energy used to maintain and manage architectures will be changed as well. In order to actively cope with rapidly changing global climate which drives changes from the basic behavior of our lives to subtle changes, international cooperation and researches are performed around the word. For instance, as a part of these global efforts, research on typical meterological data for computer simulation program to evaluate architecture energy performance is in progress in Korea. In order to conduct research on typical meterological data in format of data per time, reference regarding monthly maximum/minimum temperature time is required. Unfortunately, however, reference regarding maximum/minimum temperature time hasn't been defined in Korea. Therefore, this study aims to provide fundamental data essential for various researches by calculating maximum/minimum temperature time of major cities across Korea. According to the study, maximum temperature occurs at 3 p.m and minimum temperature occurs at 5 a.m or 6 a.m. respectively, in overall areas.

• Environmental Engineering Research
• /
• 제21권4호
• /
• pp.409-419
• /
• 2016

As a major energy consumption province, the issue about the carbon emissions in Hebei Province, China has been concerned by the government. The carbon emissions can be effectively reduced due to a more rational energy consumption structure. Thus, in this paper the constraint of low carbon emissions is considered as a foundation and four energies--coal, petroleum, natural gas and electricity including wind power, nuclear power and hydro-power etc are selected as the main analysis objects of the adjustment of energy structure. This paper takes energy cost minimum and carbon trading cost minimum as the objective functions based on the economic growth, energy saving and emission reduction targets and constructs an optimization model of energy consumption structure. And empirical research about energy consumption structure optimization in 2015 and 2020 is carried out based on the energy consumption data in Hebei Province, China during the period 1995-2013, which indicates that the energy consumption in Hebei dominated by coal cannot be replaced in the next seven years, from 2014 to 2020, when the coal consumption proportion is still up to 85.93%. Finally, the corresponding policy suggestions are put forward, according to the results of the energy structure optimization in Hebei Province.