• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2002년도 추계학술대회 논문집
• /
• pp.379-384
• /
• 2002

The effect of size and volume fraction of ceramic particles with sliding velocity on the wear properties were investigated for the metal matrix composites fabricated by pressureless infiltration process. The particulate metal matrix composites exhibited about 5.5 - 6 times of excellent wear resistance compared with AC8A alloy at high sliding velocity, and as increasing the particle size and decreasing the volume fraction the wear resistance was improved. The wear resistance of metal matrix composites and AC8A alloy exhibited different aspects. Wear loss of AC8A alloy increased with sliding velocity linearly. whereas metal matrix composites indicated more wear loss than AC8A alloy at slow velocity region, however a transition point of wear loss was found at middle velocity region which show the minimum wear loss, and wear loss at high velocity region exhibited nearly same value with slow velocity region. In terms of wear mechanism, the metal matrix composites exhibited the abrasive wear at slow to high sliding velocity generally, however AC8A alloy showed abrasive wear at low sliding velocity and adhesive and melt wear at high sliding velocity.

• Journal of the Korean Wood Science and Technology
• /
• 제34권2호
• /
• pp.30-36
• /
• 2006

Wood fuel must be dried before combustion to minimize the energy loss. Sawdust of Japanese red pine was dried in a batch type fluidized-bed to investigate the drying characteristics of sawdust as a raw material for bio-fuel. The minimum fluidization air velocity was increased as particle size was increased. It took about 21 minutes and 8 minutes to dry 0.08 m-deep bed of particles with average particle size of 1.3 mm from 100% to 10% moisture content at air temperature of $20^{\circ}C$ and $50^{\circ}C$, respectively.

• Journal of Welding and Joining
• /
• 제20권4호
• /
• pp.491-497
• /
• 2002

Dynamic behavior of the molten drop during the peak period in the pulsed-GMAW is simulated in this work using the VOF(volume of the fluid) algerian. The dynamic characteristics of molten drop such as minimum radius, average velocity and displacement of mass center were computed as well as the internal pressure and velocity. The minimum and maximum peak durations for detaching a drop were calculated.. The result of Analysis reveals that peak current and volume of pendant drop are important factors which affecting drop detachment. A simplified model of constant acceleration is proposed to describe the behavior of molten drop during peak current, and its results agree with the experimental results.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1992년도 한국자동제어학술회의논문집(국제학술편); KOEX, Seoul; 19-21 Oct. 1992
• /
• pp.370-375
• /
• 1992

An algorithm for the notion planning of the robotic hand is proposed to generate finite displacements and changes in orientation of objects by considering sliding effects between the fingertips and the object at contact points. Specifically, an optimization problem is firstly solved to find minimum contact forces and minimum joint velocities to impart a desired motion to the object at each time step. Then the instantaneous relative velocity at the contact point is found by determining velocities of the fingertip and the velocity of the object at the contact point. Finally time derivatives of the surface variables and contact angle of the fingertip and the object at the present time step is computed using the Montana's contact equation to find the contact parameters of the fingertip and the object at the next time step. To show the validity of the proposed algorithm, a numerical example is illustrated by employing the robotic hand manipulating a sphere with three fingers each of which has four joints.

• Journal of Biosystems Engineering
• /
• 제9권1호
• /
• pp.11-21
• /
• 1984

This study was intended to analyze the dynamic force system which induced the shattering of paddy grains. A model to predict the shattering of paddy grains was developed, and physical quantities, such as mass distribution and rigidity of rice plant, needed for evaluating the minimum shattering forces were also measured. Under the assumption that rice plant right before harvesting is a vibratory system, the mathematical model of the vibratory system was developed and solved with the varied conditions of forcing functions. The results of the study were summarized as follows: 1. The shattering of grain occurred at the abscission layer of grain by the bending moments resulted from the impact force due to the collision of panicles of rice plant. 2. The vibratory model developed for milyang 23 rice variety was analyzed to give the natural frequencies of 7-9 Hz, which were closely related with the excitation frequencies of 4-10 Hz caused by various machine parts besides engine. Thus, avoiding the resonance should be taken into consideration in the design of the harvesting machinery. 3. It was analyzed to predict the lowest frequency that could develop the shattering when the excitation force was applied to the lower end of stem. The lowest frequency for the Milyang 23 rice variety ranged from 8.33 Hz to 11.66 Hz as the amplitude varied from 1 cm to 2.5 cm. 4. The degree of shattering depended upon the magnitude of the impact force and its application point. For Milyang 23 rice variety, the minimum impact force developing the shattering was $5g_f$ when it was applied at 1 cm above the lower end of stern and $1g_f$ when applied at 5 cm above the lower end of stem. 5. The minimum colliding velocity of the panicle, when it was on the ground that would just develop the shattering, was given as follows, $$V=\sqrt{\frac{K_t}{m_g}{\cdot}{{\phi}^2}}$$ where V : The colliding velocity of the panicle against ground to cause the shatteering of rice grain. (cm/sec) $K_t$ : The minimum spring constant for bending at the abscission layer of grain. (dyne-cm/rad) ${\phi}$ : The minimum shattering angle of grain (rad) $m_g$ : The maximum mass of grain. (g).

• Water Engineering Research
• /
• 제1권4호
• /
• pp.299-307
• /
• 2000

The method for estimating the minimum instream flows required for the riverline aesthetics, proposed by the Kim et al.(1996), has been applied to the main channel reach of the Keum river basin in Korea. To determine the minimum instream flows for eight main reaches at Keum river basin, six representative stations have been selected. This paper provides an analysis of influence on the riverline aesthetics, which is affected by change of physical components of river, by using the survey-based quantification method. The developed questionnaire based on the literature, and submitted to the 326 people who visited an each representative station. This surveying had been implemented in three times at each representative station and we had been selected a different flowrate at each implementation. The results of this analysis and survey have produced the relationship between the variation of physical components and riverline aesthetics. Survey results bout the flow comparison are summarized as follows. At the view of riverline aesthetics, most of the respondents re sensitive at the change of the flow velocity and they prefer high water level to low water level. Moreover whole respondents prefer to abundant stream flows and moderate flow velocity. The minimum flows for riverline aesthetics is estimated at each representative station by using the survey-based quantification method and the estimated results of some representative station are greater than mean monthly flow at each station. The result of the analysis appears that establishing minimum instream flows for riverline aesthetics is not only a technical problem but a legal problem. Therefore in the case of establishing the instream flows in the river, the estimated results have to be considered as relative standard.

• 소음진동
• /
• 제10권2호
• /
• pp.221-228
• /
• 2000

In this paper, analytical study is performed to reduce residual vibration in seeking mode of optical pick-up. The conditions for acceleration adn deceleration time in trapezoidal velocity profile to reduce residual vibration are derived for undamped vibration system. To verify the validity of conditiosn two example studies are carried out. Numerical and experimental implementations for flexible arm system attached to moving part show that residual vibration is effectively reduced by calculated velocity profile. In addition, simulation study for optical pick-up reveals that by changing natural frequency to resonance frequency the conditions derived assuming undamped system can be applied to obtain velocity profile for minimum residual energy in damped vibration system.

• 한국공작기계학회논문집
• /
• 제17권1호
• /
• pp.59-64
• /
• 2008

Micro machining can manufacture complex shapes with high accuracy. Especially, this enables wide application of micro technology in various fields. For example, micro channels allow fluid transfer, which is a widely used technology. Therefore, liquidity research of flow in micro channels and micro channel manufacturing with use of various materials and cutting conditions has very important meaning. In this study, to find out correlation between fluid velocity in micro channels and surface roughness, we manufactured micro channels using micro end-mill and dropped ethanol into micro channels. We compared several surface roughness and fluid velocity in micro channels that were created by various processing conditions. Finally, we found out relationship between fluid velocity and surface roughness in micro channels of different materials.

• 한국자동차공학회논문집
• /
• 제2권5호
• /
• pp.85-92
• /
• 1994

Characteristics of breakup of a liquid droplet impinging on a hot surface has been investigated experimentally by using decane fuel. Factors influencing droplet breakup are surface temperature, impinging velocity, droplet diameter and incident angle. Droplets impinging on a hot surface begins to breakup at $220{\sim}235^{\circ}C$. This temperature varies with impinging Velocity, droplet diameter and incident angle. For wall temperature of $220{\sim}245^{\circ}C$ and above $270^{\circ}C$, breakup probability increases as impinging velocity increases showing S shape curve. For $245{\sim}265^{\circ}C$, a local minimum heat transfer rate occurs. In this temperature range, breakup probability shows nonmonotonous behavior as functions of impinging velocity. As droplet diameter decreases, impinging velocity required for droplet breakup increases. An optimum impinging angle for droplet breakup exists which are found to be about $75^{\circ}$.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2010년도 제34회 춘계학술대회논문집
• /
• pp.217-225
• /
• 2010

격벽 착화 모듈은 도우너 화약이 폭발하면서 발생한 충격파가 격벽을 통해 억셉터 화약에 전달되었을 때 동작한다. 격벽 착화 모듈의 가장 중요한 설계 요소인 격벽의 최소 두께를 결정하기 위하여 구조해석을 수행한 결과 격벽의 두께가 0.1 mm 이상인 경우 구조적으로 충분한 마진이 있음을 확인하였다. 격벽의 적정 두께를 결정하기 위하여 VISAR 간섭계를 이용하여 억셉터 화약 충전면에서 자유 표면 속도를 계측하였다. 이 속도를 이용하여 충격 압력으로 환산하고 그 결과를 억셉터 화약의 반응 민감도와 비교함으로서 격벽 두께에 따른 격벽 착화 모듈의 작동 신뢰도를 계산하였다.