• 소성∙가공
• /
• 제19권4호
• /
• pp.203-209
• /
• 2010

In the hot press forming process (HPF), a martensitic structure is obtained by controlling the cooling rate when cooling a boron sheet that is heated up to over $900^{\circ}C$. The HPF process has various advantages such as the improvement in formability and material properties and minimal spring back of the deformed materials. The factors related to the cooling rate depend on the heat transfer characteristics between heated materials and dies. Therefore, in this study, the cooling rate is controlled by adjusting the heat transfer coefficient of the material at the pressing process. And, the mechanical properties and microstructure of the deformed material is demonstrated during the HPF process where cold dies are used to form the heated steel plate. This is achieved by varying the major forming conditions that control the cooling rate regarded as the most important process parameter.

• 한국정보과학회논문지:소프트웨어및응용
• /
• 제32권12호
• /
• pp.1157-1163
• /
• 2005

본 논문에서는 방대한 양의 방송 데이타를 처리하기 위하여 MPEG(Motion Picture Expert Group) 스트림 비디오에서 빠르고 효과적으로 비디오를 분할하는 기법을 제안한다. 이를 위해, MPEG 압축 도메인에서 최소 디코딩을 수행하여 I-프레임의 DC 이미지를 추출함으로써 통해 실행 시간을 단축하고, 밝기 정보와 색상 정보를 함께 고려한 변형된 히스토그램 비교법을 도입하여 장면전환을 빠르고 정확하게 검출하였다. 그리고 추출된 장면전환에 대해 앵커 프레임과 비앵커 프레임을 구별하기 위해 신경망 기법을 도입하였다.

• Food Science and Biotechnology
• /
• 제18권6호
• /
• pp.1511-1514
• /
• 2009

Liquid whole egg (LWE) was subjected to high hydrostatic pressure (HHP), a consecutive combination of nisin and HHP (nisin-HHP), or a consecutive combination of ultrasound and HHP (ultrasound-HHP), and functional properties of processed LWE were compared to those of raw LWE. Little changes in foaming and emulsifying properties were observed by the application of HHP alone and the combined process of nisin and HHP. In contrast, ultrasound-HHP combination resulted in significant changes in color, foaming, and emulsifying properties. The maintenance of functional properties after HHP treatment agreed with expectation, because the HHP processing condition had been selected where minimal rheological changes had occurred.

• Journal of Electrical Engineering and information Science
• /
• 제2권3호
• /
• pp.1-6
• /
• 1997

This paper describes the design of a network interface controller (NIC) chip which is to be used to support a novel adaptive virtual cut-through routing method for parallel compute systems with direct (i.e., point-to-point) interconnection networks. The NIC chip is designed to provide the interface between a processing node constructed from commercially available microprocessors and another custom-designed router chip, which in turn performs the actual routing of packets to their respective destinations. The NIC, designed using a semi-full-custom VLSi design technique outperform traditional wormhole routing with a minimal amount of hardware overhead. The NIC design has been fully simulated and laid out using a 0.8$\mu\textrm{m}$ CMOS process.

• JSTS:Journal of Semiconductor Technology and Science
• /
• 제14권4호
• /
• pp.407-418
• /
• 2014

As the high-throughput requirement in the next generation communication system increases, it becomes essential to implement high-throughput SISO (Soft-Input Soft-Output) decoder with minimal hardware resources. In this paper, we present the comparison results between cascaded radix-4 ACS (Add-Compare-Select) and LUT (Look-Up Table)-based radix-4 ACS in terms of delay, area, and power consumption. The hardware overhead incurred from the retiming technique used for high speed radix-4 ACS operation is also analyzed. According to the various analysis results, high-throughput radix-4 SISO decoding architecture based on simple path metric recovery circuit is proposed to minimize the hardware resources. The proposed architecture is implemented in 65 nm CMOS process and memory requirement and power consumption can be reduced up to 78% and 32%, respectively, while achieving high-throughput requirement.

• 한국컴퓨터정보학회논문지
• /
• 제21권12호
• /
• pp.27-33
• /
• 2016

In this paper, we propose the bilateral filter based on median value that can reduce random noise and impulse noise with minimal loss of contour information. In general, EO / IR camera to generate a random or impulse noise due to a number of reasons. This noise reduces the performance of detecting and tracking by signal processing. To reduce noise, our proposed bilateral filter sorts the values of the target pixel and the peripheral pixels, and extracts a median filter coefficients of the Gaussian type. Then to extract the Gaussian filter coefficient involved with the distance between the center pixel and the surrounding pixels. As using those filter coefficients, our proposed method can remove the various noise effectively while minimizing the loss of the contour information. To validate our proposed method, we present experimental results for several IR images.

• ETRI Journal
• /
• 제38권1호
• /
• pp.81-89
• /
• 2016

In this paper, a beam ID preamble (BIDP) technique, where a beam ID is transmitted in the physical layer, is proposed for efficient beam training in millimeter-wave cellular communication systems. To facilitate beam ID detection in a multicell environment with multiple beams, a BIDP is designed such that a beam ID is mapped onto a Zadoff-Chu sequence in association with its cell ID. By analyzing the correlation property of the BIDP, it is shown that multiple beams can be transmitted simultaneously with the proposed technique with minimal interbeam interference in a multicell environment, where beams have different time delays due to propagation delay or multipath channel delay. Through simulation with a spatial channel model, it is shown that the best beam pairs can be found with a significantly reduced processing time of beam training in the proposed technique.

• Steel and Composite Structures
• /
• 제18권3호
• /
• pp.757-773
• /
• 2015

This work attempts to implement multiple regression analysis (MRA) for modeling and predicting the shear buckling strength of a steel beam with corrugated web. It was recognized from theoretical and experimental results that the shear buckling strength of a steel beam with corrugated web is complicated and affected by several parameters. A model that predicts the shear strength of a steel beam with corrugated web with reasonable accuracy was sought. To that end, a total of 93 experimental data points were collected from different sources. Then mathematical models for the key response parameter (shear buckling strength of a steel beam with corrugated web) were established via MRA in terms of different input geometric, loading and materials parameters. Results indicate that, with a minimal processing of data, MRA could accurately predict the shear buckling strength of a steel beam with corrugated web within a 95% confidence interval, having an $R^2$ value of 0.93 and passing the F- and t-tests.

• 대한산업공학회지
• /
• 제29권1호
• /
• pp.78-89
• /
• 2003

Ordering is performed to reduce the amount of fill-ins of the Cholesky factor of a symmetric positive definite matrix. This paper proposes a new ordering algorithm that reduces the fill-ins of the Cholesky factor iteratively by elimination tree rotations and clique separators. Elimination tree rotations have been used mainly to reorder the rows of the permuted matrix for the efficiency of storage space management or parallel processing, etc. In the proposed algorithm, however, they are repeatedly performed to reduce the fill-ins of the Cholesky factor. In addition, we presents a simple method for finding a minimal node separator between arbitrary two nodes of a chordal graph. The proposed reordering procedure using clique separators enables us to obtain another order of rows of which the number of till-ins decreases strictly.

• 소성∙가공
• /
• 제12권5호
• /
• pp.449-456
• /
• 2003

Multi-step induction heating process was applied to the powder compact melting technique as a new heating process to achieve pinpoint accuracy, faster cycle time, repeatability, non-contact and energy-efficient heat in a minimal amount of time. The objective of this study is the establishment of the input data diagram of multi step induction heating process for automation of the fabrication process of 6061 Al foams with desired density. At first, proper induction coil was designed to obtain a uniform temperature distribution over the entire cross sectional area of specimen. By using this coil, foaming experiments were performed to investigate the multi-step induction heating conditions such as capacity, temperature and time conditions of each heating and holding step. On the basis of the obtained multi-step induction heating conditions, relationship between final heating temperature and fraction of porosity was investigated.