• 한국재료학회지
• /
• 제11권12호
• /
• pp.1068-1073
• /
• 2001

An n-type iron$silicide(Fe_{0.98}Co_{0.02}Si_2)$has been produced by mechanical alloying process and consolidated by vacuum hot pressing. Although as-milled powders after 120 hours of milling did not show an alloying progress,${\beta}-FeSi_2$phase transformation was induced by isothermal annealing at$830{\circ}C$for 1 hour, and the fully transformed${\beta}-FeSi_2$phase was obtained after 4 hours of annealing. Near fully dense specimen was obtained after vacuum hot pressing at$ 1100{\circ}C$with a stress of 60MPa. However, as-consolidated iron silicides were consisted of untransformed mixture of ${\Alpha}-Fe_2Si_5$and ${\varepsilon-FeSi$phases. Thus, isothermal annealing has been carried out to induce the transformation to a thermoelectric semiconducting${\beta}-FeSi_2$phase. The condition for${\beta}-FeSi_2$transformation was investigated by utilizing DTA, SEM, and XRD analysis. The phase transformation was shown to be taken place by a vacuum isothermal annealing at$830{\circ}C$and the transformation behaviour was investigated as a function of annealing time. The mechanical properties of${\beta}-FeSi_2$materials before and after isothermal annealing were characterized in this study.

• 한국재료학회지
• /
• 제11권12호
• /
• pp.1035-1041
• /
• 2001

The refining process and solubility of Ti in Al matrix during mechanical alloying (MA) were investigated by using X-ray diffraction (XRD), transmission electron microscopy (TEM) as functions of alloy composition, milling time and ball to powder ratio (BPR). Mechanical alloyed samples were annealed for investigating their stability and the formation behavior of$Al_3Ti$in the temperature range from$200{\circ}C$to$600{\circ}C$. It is observed from present experimental that disappearance of Ti peaks in mechanically alloyed Al-10wt%Ti is not simply attributable to the dissolution of Ti into Al, but associated mainly with extreme refining and/or heavy straining of Ti particles The annealing of the mechanically alloyed Al-Ti powders show differences in aluminide formation behavior when Ti content in Al is equal to or less than l0wt% and higher than l5wt%Ti. When Ti-content in Al is equal to or less than l0wt%, the MA powders transform directly to a global equilibrium state forming $DO_{22}- type\;Al_3$Ti above$400{\circ}C$. In the Al-Ti samples with equal to or higher than l5wt%Ti, transitional phases of cubic$Al_3Ti$and tetragonal $Al_{24}Ti_8$ are formed above$400{\circ}C$. They are stable only below$500{\circ}C$, and, $DO_{22}-type\;Al_3Ti$ becomes dominant aluminide at temperature higher than$ 600{\circ}C$.

• Maxillofacial Plastic and Reconstructive Surgery
• /
• 제38권
• /
• pp.2.1-2.9
• /
• 2016

Background: We reviewed the biological and mechanical properties of porous hydroxyapatite (HA) compared to other synthetic materials. Computer-aided design/computer-aided manufacturing (CAD/CAM) was also evaluated to estimate its efficacy with clinical and radiological assessments. Method: A systematic search of the electronic literature database of the National Library of Medicine (PubMed-MEDLINE) was performed for articles published in English between January 1985 and September 2013. The inclusion criteria were (1) histological evaluation of the biocompatibility and osteoconductivity of porous HA in vivo and in vitro, (2) evaluation of the mechanical properties of HA in relation to its porosity, (3) comparison of the biological and mechanical properties between several biomaterials, and (4) clinical and radiological evaluation of the precision of CAD/CAM techniques. Results: HA had excellent osteoconductivity and biocompatibility in vitro and in vivo compared to other biomaterials. HA grafts are suitable for milling and finishing, depending on the design. In computed tomography, porous HA is a more resorbable and more osteoconductive material than dense HA; however, its strength decreases exponentially with an increase in porosity. Conclusions: Mechanical tests showed that HA scaffolds with pore diameters ranging from 400 to $1200{\mu}m$ had compressive moduli and strength within the range of the human craniofacial trabecular bone. In conclusion, using CAD/CAM techniques for preparing HA scaffolds may increase graft stability and reduce surgical operating time.

• 한국재료학회지
• /
• 제22권3호
• /
• pp.150-154
• /
• 2012

Ti-6Al-4V ELI (Extra Low Interstitial) alloy have been widely used as alternative to bone due to its excellent biocompatibility, although it still has many problems such as high elastic modulus and toxicity. Therefore, biomaterials with low elastic modulus and non toxic characteristics have to be developed. A novel ${\beta}$ Ti-35wt%Nb-7wt%Zr-Calcium pyrophosphate (CPP) composite that is a biocompatible alloy without elemental Al or V was fabricated by spark plasma sintering (SPS) at $1000^{\circ}C$ under 70 MPa using high energy mechanical milled (HEMM) powder. The microstructure and phases of the milled powders and the sintered specimens were studied using SEM, TEM, and XRD. Ti-35wt%Nb-7wt%Zr alloy was transformed from ${\alpha}$ phase to ${\beta}$ phase in the 4h-milled powder by sintering. The sintered specimen using the 4h-milled powder showed that all the elements were distributed very homogeneously and had higher density and hardness. ${\beta}$ Ti alloy-CPP composite, which has nanometer particles, was fabricated by SPS using HEMMed powder. During the sintering process, $CaTiO_3$, TixOy, and CaO were formed because of the reaction between Ti and CPP. The Vickers hardness of the composites increases with the increase of the milling time and the addition of CPP. The biocompatibility of the Ti-Nb-Zr alloys was improved by addition of CPP.

• 한국전자파학회논문지
• /
• 제17권5호
• /
• pp.423-429
• /
• 2006

본 논문은 실용적인 면을 고려한 휴대전화 단말기용 전파 흡수체 개발을 위해 연구하였다. 이에 Sendust 배합율, $Al(OH)_3$ 코팅 함유량, 시편의 두께, 지지재의 변화가 전파 흡수체의 전파 흡수능에 치는 영향을 연구하였다. 중심 주파수는 전파 흡수체의 두께가 1 mm, 2 mm, 3 mm로 증가할수록 2.2 GHz, 1.29 GHz, 842 MHz의 저주파대로 이동하였고, Sendust의 배합율이 80 wt%에서 85 wt%로 증가되면서 2.2 GHz에서 1.91 GHz로, 1.29 GHz에서 801 MHz로, 842 MHz에서 801 MHz로 각각 저주파대로 조절할 수 있었다. 전파 흡수 대역은 Sendust에 $Al(OH)_3$를 코팅했을 때가 코팅하지 않았을 때보다 흡수 대역이 넓어졌다. 이때 전파 흡수체는 지지재는 CPE로 하였으며, 제작 온도는 $70^{\circ}C$로 일정하게 하였다. 제작된 전파 흡수체는 두께가 0.85 mm일 때 1.8 GHz에서 5.76 dB의 우수한 전파 흡수능을 보였다.

• 한국분말재료학회지
• /
• 제22권5호
• /
• pp.356-361
• /
• 2015

Fe-30 wt% TiC composite powders are fabricated by in situ reaction synthesis after planetary ball milling of (Fe, $TiH_2$, Carbon) powder mixture. Two sintering methods of a pressureless sintering and a spark-plasma sintering are tested to densify the Fe-30 wt% TiC composite powder compacts. Pressureless sintering is performed at 1100, 1200 and $1300^{\circ}C$ for 1-3 hours in a tube furnace under flowing argon gas atmosphere. Spark-plasma sintering is carried out under the following condition: sintering temperature of $1050^{\circ}C$, soaking time of 10 min, sintering pressure of 50 MPa, heating rate of $50^{\circ}C/min$, and in a vacuum of 0.1 Pa. The curves of shrinkage and its derivative (shrinkage rate) are obtained from the data stored automatically during sintering process. The densification behaviors are investigated from the observation of fracture surface and cross-section of the sintered compacts. The pressureless-sintered powder compacts are not densified even after sintering at $1300^{\circ}C$ for 3 h, which shows a relative denstiy of 66.9%. Spark-plasma sintering at $1050^{\circ}C$ for 10 min exhibits nearly full densification of 99.6% relative density under the sintering pressure of 50 MPa.

• 한국분말재료학회지
• /
• 제12권4호
• /
• pp.279-283
• /
• 2005

In this study, the ZnS composite powders for host material in phosphor was synthesized in situ by mechanical alloying. As the mechanical alloying time increases, particle size of ZnS decreases. ZnS powders of $1.85\;\mu{m}$ in a mean size was fabricated by mechanical alloying for 10h. The crystal structures of ZnS powders were investigated by X-ray diffraction and the photo-luminescence properties was evaluated with the optical spectra analyzer. The steady state condition of mechanically alloyed ZnS was obtained as a mean particle size of $2\;\mu{m}$ in 5h milling. The sphalerite and wurtize structures coexist in the ZnS mechanically alloyed for 5h. The ZnS powder mechanically alloyed for 10h grows to the sphalerite structure. And the strong emission peaks of ZnS are observed at 480 nm wave length at the powders of mechanically alloyed for 10h, but the sphalerite and wurtize structures in ZnS coexist and emission peaks are not appeared at the powders of mechanically alloyed for 10h.

• 한국재료학회지
• /
• 제13권5호
• /
• pp.292-296
• /
• 2003

In an attempt to enhance phase transformation and homogenization of Mn-doped $FeSi_2$, mechanical alloying of elemental powders was applied. Cold pressing and sintering in vacuum were carried out to produce a dense microstructure, and then isothermal annealing was employed to induce a phase transformation to the $\beta$-$FeSi_2$semiconductor. Phase transitions in this alloy system during the process were investigated by using XRD, EDS and SEM. As-milled powders after 100 h of milling were shown to be metastable state. As-sintered iron silicides consisted of untransformed mixture of $\alpha$-$Fe_2$$Si_{5}$and $\varepsilon$-FeSi phases. $\beta$-$FeSi_2$phase transformation was induced by subsequent isothermal annealing at $830^{\circ}C$, and near single phase of $\beta$-$FeSi_2$was obtained after 24 h of annealing. Thermoelectric properties in terms of Seebeck coefficient, and electrical conductivity were evaluated and correlated with phase transformation. Seebeck coefficient electrical resistivity and hardness increased with increasing annealing time due to $\beta$ phase transformation.

• 공업화학
• /
• 제29권1호
• /
• pp.43-48
• /
• 2018

본 연구에서는 PCC (precipitated calcium carbonate) 제조에 있어 칼슘이온 추출 최적화를 위하여 추출 용제, 용제의 농도, 추출원의 투입량, 전처리 공정 등 다양한 추출 조건에 따른 실험을 수행하였다. 칼슘추출원으로 CaO를 사용하였으며, 칼슘이온의 추출량과 CaO의 입자크기를 확인하기 위하여 ICP와 SEM 분석을 수행하였다. 그 결과 2 M의 hydrochloric acid를 용제로 사용한 경우 100%의 칼슘이온이 추출되었으며, 추출원의 최적 투입량은 6 g으로 확인하였다. 반면 반응시간, 반응온도, 입자 분쇄 및 열처리 공정은 칼슘이온 추출량에 큰 영향이 없음을 확인하였다.

• 한국가구학회지
• /
• 제25권1호
• /
• pp.45-54
• /
• 2014

Wood cutting utilizing CNC art in the field of furniture design industry, art, education are diverse. However, there is lack of data in the case for wood cutting, such as cutting conditions and wood cutting. So this article is to establish furniture design processing using CNC. The researchers investigated the processed products using CNC, the data of the web site and CNC relevant articles, then organized its impact on the furniture industry today. History and definition of CNC have studied for a discussion of the advantages and disadvantages. Then, the researchers analyzed the cases to investigate the wood cutting conditions, was applied to the fabrication of furniture domestic and foreign. CNC organized systematically design information through the computer So, it allowed to reduce the repetitive behavior that has to work hand in the furniture manufacture existing. CNC has made it possible to design a fine complex in furniture design industry. So it became possible to make a new representation and production of various forms. Material about CNC are mostly for milling machine and shelves for metal processing. So, the researchers investigated and precautions general content of wood cutting. The enhanced understanding to investigate an example that is applied outside the country, is used to analyze the expression various techniques CNC. It is difficult to obtain accurate data processing, it has various characteristics in the same timber, Future research is about analyzing type applications and CNC machining range at the time of processing the various wood.