• Structural Engineering and Mechanics
• /
• v.11 no.3
• /
• pp.273-286
• /
• 2001

Viscoelastic (VE) dampers have shown to be capable of providing structures with considerable additional damping to reduce the dynamic response of structures. However, the VE material appears to be sensitive to the variations in ambient temperature and vibration frequency. To minimize these effects, a new VE material has been developed. This new material shows less sensitivity to variations in vibration frequency and temperature. However, it is highly dependent on the shear strain. Experimental studies on the seismic behavior of a 2/5 scale five-story steel frame with these new VE dampers have been carried out. Test results show that the structural response can be effectively reduced due to the added stiffness and damping provided by the new type of VE dampers under both mild and strong earthquake ground motions. In addition, analytical studies have been carried out to describe the strain-dependent behavior of the VE damper. The dynamic properties and hysteresis behavior of the dampers can be simulated by a simple bilinear model based on the equivalent dissipated energy principle proposed in this study.

• Journal of Welding and Joining
• /
• v.13 no.1
• /
• pp.115-126
• /
• 1995

Vision sensors using the optical triangulation have been widely used for automatic welding systems in various ways, but their reliability is seriously affected by presence of the arc noise. The reliability of vision sensors was analyzed with variation of the arc noise by considering the reflectance of the base metal. first, the properties of the base metal's reflection were modelled by using the Bidirectional Reflectance-Distribution Function(BRDF), and then the variation of the reflected arc intensity was formulated for various configurations of the torch, base metal, and sensor. The experimental data of the gray level of the reflected arc light were obtained for two materials, mild steel and stainless steel. It was found that the results calculated from the proposed model were in good agreement with the experimental data.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2002.04a
• /
• pp.585-590
• /
• 2002

Abrasive water-jet(AWJ) machining is a new cutting technology. The AWJ can cut various materials touch as metal, glass and stone. However, the AWJ machining makes troubles including kerf, rounding and side taper. In this study, we investigated the correlation between parameters of abrasive water-jet machining arid cutting characteristics. The machining parameter were the material thickness and the traverse speed. The experiment was conducted to cut the stainless steel(STS41) and the mild steel(SS41) specimens. The results of the experiment weirs presented as the relation between cutting conditions and trouble of a dimension error, a conner error, an uncut width and a kerf.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.13 no.3
• /
• pp.1-7
• /
• 2004

Abrasive water-jet(AWJ) machining can cut various materials such as metal, glass and plastics. However, the AWJ machining has some troubles including kerf, rounding and side taper. In this study, we experimently investigated the correlation between the traverse speed of the abrasive water-jet and the dimensional error of the workpiece according to the thickness and the types of the material. The specimen was the stainless steel and the mild steel and the predetermined contour cutting was conducted. A comer radius error, an uncut width and a kerf were measured and evaluated.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.05a
• /
• pp.984-987
• /
• 2002

Abrasive water-jet(AWJ) machining is a new cutting technology. The AWJ can cut various materials such as metal, glass and stone. However, the AWJ machining makes troubles including kerf, rounding and side taper. In this study, we investigated the correlation between parameters of abrasive water-jet machining and cutting characteristics. The machining parameters were the material thickness and the traverse speed. The experiment was conducted to cut the stainless steel(STS41) and the mild steel(SS41) specimens. The results of the experiment were presented as the relation between cutting conditions and troubles of a dimension error, a conner error, an uncut width and a kerf.

• Journal of the Korean Society of Safety
• /
• v.12 no.3
• /
• pp.52-59
• /
• 1997

Hill's anisotropy theory and isotropy theory under the deformed profile assumed two separate cases(that is circular and ellipitical) are applied to predict the plastic deformation characteristics of bulge, the strain and polar height under instability condition, using thin square diaphragms of stainless steel, mild steel, brass, copper and aluminum. In this study it was found that the pressure-polar height curves, and the polar height-the polar radius of curvature curve, under anisotropy theory and isotropy theory, assuming a circle profile, agree well with the experimental results, and the equivalent strains of the instability condition under anisotropy theory are better good agreement with the experimental results than those of the instability condition under isotropy theory. Beside, FLCo(plane Strain Intercept) obtained by Bethlehem FLC method and standard FLC method (modified) agree well with the experimental result.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.9 no.3
• /
• pp.41-47
• /
• 2000

The atmospheric humidity is varied between 30% and 90% with season in Korea. Thus the influence of humidity on the behavior of wear for tools and dies. This paper presents the influence of atmospheric humidity on the wear of carbon the un-lubricated pin-on-disk sliding contact. it was found that the severe wear is dominant at a low humidity and the mild wear is strongly related with the carbon concentration of the steel at a high humidity in this study. The experiments were carried out in a chamber where the humidity was accurately maintained by humidifier. To investigate the relationship three different carbon steels such as 1020, 1041, and 1034 steels were used.

• Tribology and Lubricants
• /
• v.27 no.1
• /
• pp.1-6
• /
• 2011

The possibility of Cu-Al-Ni intermetallic coating on the mild steel through the combustion synthesis has been investigated. In particular, the effect of the ball milling energy on the microstructure of the coating layer was examined to obtain the best coating condition. Experimental results show that Cu-Al-Ni powder compact was explosively synthesized and successfully coated with the steel matrix. It was revealed that the formation of $Cu_9Al_4$ intermetallic decreased with increase in the ball milling energy. This result supports that the high energy ball milling would be effective for obtaining the most suitable microstructure for Cu-Al-Ni coating layer. However, the excessive ball milling energy seems to decrease the bonding strength between the coating layer and the matrix.

• Transactions of Materials Processing
• /
• v.19 no.7
• /
• pp.405-410
• /
• 2010

Double layered tube that has been used for transportation and oil piping system is occasionally exposed to elevated temperature. The change in stress state at elevated temperature is important for the safe design of double layered tube. In this study, the variation of stress state for hydroformed double layered tube of which inner tube is stainless steel and outer tube is mild steel has been analytically analyzed. To characterize the thermal stress at elevated temperature, analytical model to provide thermal stresses between outer tube and inner tube was developed by using theories of elasticity and Lame equation. The feasibility of analytical model is verified by finite element analysis using ANSYS $CLASSIC^{TM}$, commercially available code. The variation of thermal stress at various thickness combination of inner and outer tube has also been investigated by proposed analytical model.

• Journal of Welding and Joining
• /
• v.12 no.3
• /
• pp.71-81
• /
• 1994

Laser cutting is experiencing a rising worldwide acceptance in the industry. Expert systems are necessary for the systematic arrangement and searching of experimental data existing in journal papers, job handbooks, etc.. This paper proposes an expert system for the selection of the appropriate laser cutting variables from the available database. Optimum cutting conditions according to the given cutting velocity were searched and qualitative comments which are difficult to be used as database variables were shown at each velocity using the binary and fuzzy inference. These comments could be informative to unskilled operators of the laser cutting process. Typical cutting conditions of the mild steel and stainless steel were included and the working range and quality variations were displayed graphically. The proposed algorithm was implemented in an IBM compatible personal computer as an expert system for CO$_{2}$ laser cutting to derive the optimum cutting conditions by using the turbo prolog.