• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.42 no.12
• /
• pp.159-164
• /
• 2005

Recently, it has demanded high-speed digital circuits as information increase. Therefore, electromagnetic characteristics of compact microwave circuit occurred importantly. And, the effect of the imperfect ground plane on the signal integrity and influence of coupling between two parallel lines for high-speed digital transmission line on the printed circuit board is investigated by FDTD simulations in 3-D electromagnetic analysis method. The results of FDTD simulation are compared with the ADS simulation in commercial software, analyzed lumped element of modeling and electromagnetic wave's radiation of slot as frequency. As a consequence, when the slot in the ground plane is under microstrip line, it has much effect on propagation of wave.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.23 no.7
• /
• pp.840-843
• /
• 2012

In this paper, the authors present a new design for a dual-band metamaterial(MTM) absorber that utilizes resonant-magnetic inclusion of a split-ring resonator(SRR). The proposed MTM unit cell is constructed by two open complementary split-ring resonators(OCSRRs) and an SRR arrangement. To avoid the need for metallic back plate a planar array of SRRs for resonant-magnetic inclusion is placed facing toward the incident wave propagation direction. Each unit cell is printed on the two sides of a FR-4 substrate. A prototype absorber was fabricated with a planar array of $39{\times}39$ unit cells, and measured. The proposed backplane-less absorber can be used for microwave applications.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.15 no.4
• /
• pp.428-435
• /
• 2004

With the rapid and wide-spread use of cellular telephones much attention has been focussed on propagation in the urban area crowed with buildings and houses. It is often surrounded by hills, forests, and mountains. The importance of surface scattering intereference between transmitters and receivers on the rough surfaces has been interested and investigated. Therefore, a prediction method is necessary to estimate the influence of rough surfaces on microwave radio propagation. Moreover, most of the mobile communications are performed based on the digital communication system rather than the analog one. In this case, we must pay more careful attention to the signal delay caused by the phase delay due to the multi-path propagation. In this paper we have analyzed numerically scattering of electromagnetic waves from building walls by using FVTD(Finite Volume Time Domain) method. We consider three different types of rough surfaces such as periodic, random, and composite structures. We calculate the bistatic normalized radar cross section (NRCS) for horizontal and vertical polarization, and we take account of the conventional optical reflection which corresponds to the n-th Bragg reflection for periodic structures. In addition, we investigated what conditions are needed in order to be able to ignore the higher order Bragg reflection for the periodic structures.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.43 no.10 s.352
• /
• pp.27-34
• /
• 2006

This paper has implemented a very small($1.4{\times}2.8[Cm^2]$) 13.56[MHz] RFID reader ensuring machine ID recognition correctly in a noise space of Tag-to-Reader within 3Cm. For operation of the RFID system, at first, this paper has designed the loop antenna of a reader and the fading model of back-scattering on microwave propagation following to 13.56[MHz] RFID Air Interface ISO/IEC specification. Secondly, this paper has proposed the automatically path selected RF switching circuit and the firmware operation relationship by measuring and analyzing the very small RFID RF issues. Finally, as a very small reader main body, this paper has shown the DSP board and software functions made for extraction of $1{\sim}2$ machine ID information and error prevention simultaneously with carrying of 13.56[MHz] RFID signals that the international standard specification ISO/IEC 18000-3 defined.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.25 no.3
• /
• pp.339-347
• /
• 2014

In this paper, the authors present a new design for a broad-band metamaterial(MTM) absorber that utilizes flexible substrate. The proposed MTM unit cell is constructed by a electric-inducive-capacitive(ELC) resonator and a cut-wire on the same side of the flexible polyimide substrate. To reduce the radar cross section at frequencies other than the targeted frequency bands, the metallic pattern layer of the proposed structure is placed facing toward the incident wave propagation direction. A prototype absorber was fabricated with a planar array of $33{\times}45$ unit cells. Our experiments showed that the proposed absorber exhibits a peak absorption rate of 92 % and 93 % at 9.06 GHz and 15.0 GHz, respectively, and 75 % of the full-width at half-maximum(FWHM) bandwidth is achieved. The proposed backplane-less MTM structure can be used for a broad-band microwave absorber and irregular surface applications.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.17 no.3
• /
• pp.261-269
• /
• 2004

The existing concrete beams can be retrofitted or reinforced by attaching carbon fiber or glass fiber sheet beneath the beams. Although diverse design methods and application techniques of the retrofitting are studied and developed, the testing method of examining retrofitted beams have not been put into practice yet. In this study, a bond delamination has been modeled and studied to provide a basis for the development of actual testing equipments. For this purpose, Gaussian and sinusoidal waves with 3GHz and 5GHz center frequency are used as an incident wave and 1mm and 3mm bond delamination under the reinforcement are modeled. In the modeling, Finite Difference-Time Domain algorithm is used to investigate the behavior of electromagnetic waves in concrete. The results have shown that 5GHz waves are suitable for the detection of delamination.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.45 no.12
• /
• pp.139-145
• /
• 2008

In this paper, a microstrip surface wave antenna(SWA) with a frequency selective surface structure(FSS) is designed and measured. A microstrip SWA has many advantages such as low profile, low weight, easy fabrication, and compatibility with monolithic microwave integrated circuits(MMIC). In addition, it has demonstrated monopole like beam patterns. The microstrip SWA consists of two parts : a center-fed modified microstrip patch to excite surface wave, and a periodic patches to support the propagation of the surface waves. To obtain wide bandwidth, the ring type parasitic element is inserted and the circular patch is selected for the unit element in FSS structure. Experimental results show that the microstrip SWA has monopole like beam patterns at 5.9GHz. Impedance bandwidth and gain is 12% and 5.6dBi.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.32 no.3
• /
• pp.141-147
• /
• 2019

In this paper, a systematic beam splitter design for multi-beam forming is proposed. The objective of this research is to a design beam splitter that splits and focuses scattering microwaves into intense beams in multiple directions. It is difficult to split multi-beam to non-specific directions with theoretical approaches. Therefore, instead of using transformation optics(TO), which is a widely used process for controlling electromagnetic wave propagation, we used a systematic design process called the phase field design method to obtain an optimal topological structure of beam splitter. The objective function is to maximize the norm of electric field of the target areas of each direction. To avoid island structure and obtain the structure in one body, volume constraint is added to the optimization problem by using augmented Lagrangian. Target frequency is set to X-band 10GHz. The optimal beam splitter performed well in multi-beam forming and the transported electric energy of target areas improved. A frequency dependency test was conducted in the X-band to determine effective frequency range.

• Journal of Broadcast Engineering
• /
• v.19 no.3
• /
• pp.372-384
• /
• 2014

DTV field tests have been performed to measure field strength and to check reception ratio on indoor and outdoor sites. They use an antenna of 9m to measure DTV signal in case of outdoor measurement on the road. Modern skyscrapers require the analysis of vertical-directional wave propagation by measuring vertical-directional DTV signal. Even if the field strength is above the reception threshold of $43dB{\mu}V/m$, the reception is impossible in case of strong multi-path or high impulse noise. So, vertical-directional field measurement is essential in environment of tall buildings. In this paper, we developed an octo type multi-copter to measure vertical-directional DTV signal level. A compact and portable DTV signal level meter, an antenna, a microwave transmitter for data transmission, and a recording equipment are equipped in the multi-copter. Three different sites are selected to test the measurement system. Developed measurement system using the multi-copter is very useful in measuring vertical-directional DTV signal, especially in apartments, non-accessible area by vehicles, and forbidden areas.