• Journal of electromagnetic engineering and science
• /
• 제5권4호
• /
• pp.153-160
• /
• 2005

In this paper, the novel microwave oscillator incorporating a planar cavity resonator(PCR) is presented to reduce the phase noise of the oscillator in a planar environment. Compared to the conventional planar( $\lambda$/4 open stub resonator), the phase noise is improved about 16 dBc/Hz @100 kHz. The design of the oscillator is based on a reflection type configuration using the low 1/f SiGe HBT transistor(LPT16ED). The output power is measured 2.76 dBm at 12.5 GHz. In this paper, the oscillator used to the PCR can be expected to provide a solution for low phase noise oscillator in microwave circuits.

• 한국통신학회논문지
• /
• 제21권5호
• /
• pp.1304-1316
• /
• 1996

In this paper, A VCO(Voltage Controlled Oscillator) in use of clock recovery/data regeneration circuit for 10 Gbps fiber optic receivers was developed. The improved hair-pin resonator with a parallel coupled lines, which has been applied to microstrip filters, was used as a resonance part. As a frequcncy tuning device by substituting 3-terminalMESFET vaaractor for varactor diode, an MMIC manufacturing process will be simplified. Since a hair-pin resonator is planar type compared to the dielectric resonator and has a relatively flat reactance verus frequency, it will be favorable to apply a hair-pin resonator to an MMIC, in addition wideband frequency tuning range is able to be obtained.

• 한국통신학회:학술대회논문집
• /
• 한국통신학회 1984년도 춘계학술발표회논문집
• /
• pp.25-28
• /
• 1984

This paper describes the design of band-pass filter using the dielectric resonator and microstrip line depends mainly upon the magnetic field and is principal parameter as band-pass filter. Because dielectric resonator band~pass filter has a very high-Q, the bandwidth of this filter is very narrow. as a result of experiment, the dielectric resonator bandwidth of this filter is very narrow. As a result of experiment, the dielectric resonator band-pase filter has various modes central frequencies due to the mode change and good characteristric as a band-pass filter.

• 한국ITS학회 논문지
• /
• 제3권2호
• /
• pp.85-93
• /
• 2004

In this paper, microstrip stepped-impedance hairpin resonator (SIR) lowpass filter f.PF) by surface rnicromachining on GaAs substrate is sugsested. This filter has the advantages of compact side, easy fabrication, and sharp cutoff frequency response. The new SIR LPF shows the 3 dB passband of dc to 33 GHz, the insertion loss of 0.82 dB, and the return loss of better than 17 dB up to 25.57 GHz. This filter is useful for many microwave system applications.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1997년도 추계학술대회 논문집 학회본부
• /
• pp.288-290
• /
• 1997

Pulsed laser ablation has been used to fabricate superconducting $YBa_2Cu_3O_{7-x}$(YBCO) thin films on MgO substrates. The epitaxial YBCO thin films were grown at $750^{\circ}C$ and oxygen partial pressure of 200 mTorr. The electrical property and the characteristics of the YBCO thin films have been studied by R-T measurement. scanning electron microscopy (SEM) and X-ray diffraction (XRD). A microstrip line resonator has been fabricated using YBCO superconducting thin films by photolithography and wet-etch process. The resonator has linear microstrip line separated by a gap of 0.278 mm. We observed a fundamental resonance peak at the frequency of 10.007 GHz.

• Journal of electromagnetic engineering and science
• /
• 제12권3호
• /
• pp.210-215
• /
• 2012

This paper presents a compact microstrip triple-mode filter with enhanced skirt characteristics. The presented triple-mode filter configuration supports three transmission poles and three transmission zeros within the nearby passband. Two of transmission zeros are generated by a triple-mode resonator itself, and the third one is generated by small cross-couplings between the I/O ports. Each resonance condition and the transmission zero generation conditions are analyzed using an equivalent circuit. The bandpass filter is designed for a 2.4 GHz WLAN. The filter was fabricated with a relative dielectic constant of 3.5 and a thickness of 0.76 mm. The fabricated filter has a small size ($7.9mm{\times}7.2mm$, i.e., $0.107{\lambda}_g{\times}0.098{\lambda}_g$, where ${\lambda}_g$ is guided wavelength at a center frequency) and shows high performing skirt characteristics.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제53권7호
• /
• pp.395-400
• /
• 2004

In this paper, the four-pole elliptic function microstrip filter at 2.4GHz band with fractional bandwidth of 4% is realized using compact miniaturized hairpin resonators. The parallel algorithm FDTD method is used to analyze S-parameter of hairpin resonator filter more accurately, and to calculate the electric coupling and magnetic coupling among the hairpin resonators. Absorbing boundary conditions for mesh termination used Sulivan's simplified PML and the FDTD code was paralleled by MPI for IBM SP2 which had enhanced calculation speed. The experimental measurements are performed by HP8720D vector network analyzer. Measured results on fabricated hairpin type cross coupled bandpass filters show good agreements with theoretic results.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2005년도 하계학술대회 논문집 Vol.6
• /
• pp.309-310
• /
• 2005

Generally, the dielectric constant and loss tangent are gotten by resonators. This paper presents analysis of the comparing the dielectric constant and loss tangent from the Ring, T and series gap structures. The T structure can be analyzed easily at wideband characteristic with simple design. the Ring can ignore the radiation loss from the open-ended effect. the Series gap can get more accurate permittivity than a Ring structure. The Used materials were dupont9599 LTCC ceramic and daeju0086 Ag.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2010년도 하계학술대회 논문집
• /
• pp.341-341
• /
• 2010

• 한국ITS학회:학술대회논문집
• /
• 한국ITS학회 2004년도 제3회 정기총회 및 추계학술대회
• /
• pp.306-310
• /
• 2004