• Journal of the Korean Society for Precision Engineering
• /
• v.16 no.3 s.96
• /
• pp.72-77
• /
• 1999

This paper presents 2-dimensional vibration cutting increases dynamic stiffness of tool support and improves the quality of machined surface in micro-machining. 2-dimensional vibration cutting is generated by two piezo actuators arranged orthogonally. A sine-type voltage is input to one actuator and a phase-shifted sine-type voltage is input the other. Then the vibration device actuates the tool in a 2-D elliptical motion with pulsed cutting force. It is a characteristic of 2-D vibration cutting that some negative thrust force occurs as the direction of friction on a tool rake surface is reversed. It helps not only chip flow smoothly and continuously but also cutting force be reduced. The quality of machined surface by 2-D vibration cutting depends on such parameters as vibration amplitude, frequency, cutting speed, depth of cut, etc. Compared to conventional cutting through tool path simulation and experiments under several conditions, the 2-D vibration cutting is verified to bring forth a great decrease of cutting forces, much better surface roughness and moreover much less burr.

• Clinical and Experimental Reproductive Medicine
• /
• v.43 no.3
• /
• pp.146-151
• /
• 2016

Objective: This study was conducted to compare the effects of static culture, dynamic culture, and the combination of dynamic culture with specialized surfaces involving co-culture on human embryonic development. Embryos cultured using conventional static culture (SC) techniques served as a control group. We compared dynamic culture using micro-vibration culture (MVC) and micro-vibration with co-culture (MCoC), in which autologous cumulus cells were used as a specialized surface. Methods: We conducted a chart review of patients who were treated between January 2011 and November 2014 in order to compare embryonic development rates and pregnancy rates among the groups. Zygotes were cultured in micro-droplets, and embryos were subsequently selected for transfer. Some surplus embryos were cryopreserved, and the others were cultured for blastocyst development. A micro-vibrator was set at the frequency of 42 Hz for duration of 5 seconds per 60 minutes to facilitate embryo development. Results: No significant differences among the groups were present in patient's characteristics. However, the clinical pregnancy rates were significantly higher in the MVC group and the MCoC group than in the SC group. No significant differences were found in the blastocyst development rate between the SC group and the MVC group, but the blastocyst development rate in the MCoC group was significantly higher than in the SC and MVC groups. Conclusion: The clinical pregnancy rate was significantly increased by the application of micro-vibration to the embryonic cultures of poor responders. The blastocyst development rate was significantly increased by the application of MCoC to surplus embryos.

• Progress in Superconductivity and Cryogenics
• /
• v.3 no.2
• /
• pp.44-48
• /
• 2001

SMES consists of Superconducting magnet, a power converter, a cryostat and HTS current leads The prototype cryostat with HTS current leads and refrigerators was designed and manufactured for developing micro SMES. The temperature rise under dc current in HTS current leads was measured. The performances of helium boil-off and mechanical stress were evaluated during transfer and vibration tests. The results will be used to develope the micro-SMES system.

• Journal of the Korean Society for Precision Engineering
• /
• v.22 no.12 s.177
• /
• pp.190-197
• /
• 2005

For precise micro-grooving and surface machining, a mechanism for creating elliptical vibration cutting (EVC) motion is proposed which uses two parallel piezoelectric actuators. And based on its kinematical analysis, variations of EVC path are investigated as a function of dimensional changes in the mechanism, phase difference and amplitude of excitation sinusoidal voltages. Using the proposed PZT mechanism, various types of two dimensional EVC paths including one dimensional vibration cutting path along the cutting direction and thrust direction can be easily obtained by changing the phase lag, the amplitude of the piezoelectric actuators, and the dimension of the mechanism.

• Journal of the Korean Society for Precision Engineering
• /
• v.22 no.12 s.177
• /
• pp.198-204
• /
• 2005

For precise micro V-grooving, ultrasonic elliptical vibration cutting (UEVC) is proposed using two parallel piezoelectric actuators, which are energized by sinusoidal voltages with a phase difference of 90 degrees. Experimental setup is composed of stacked PZT actuators, a single crystal diamond cutting tool, and a precision motorized xyz stage. It is found that the chip formed in the process of UEVC is discontinuous because of the periodic contacts and non-contacts occurring between the tool and workpiece. It is experimentally observed that the cutting force in the process of UEVC significantly reduces compared to the ordinary non-vibration cutting. In addition, the creation of burr during UEVC is significantly suppressed, which is attributable to the decrease in the specific cutting energy.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2004.05a
• /
• pp.332-336
• /
• 2004

To position precision machines accurately, linear motion (LM) guides having rolling elements can be used. For ultra-accurate positioning control of the precision machines, the understanding of the dynamic behavior of the LM guide at the macro and/or micro scales is most critical, but the research on this subject is rare. The objective of the present research is to observe the vibration phenomena of the LM guide. Bails are used as the rolling elements in this work. Several experiments show the nonlinear characteristics of the LM guide such as hysteresis behavior and force-dependent natural frequencies phenomena.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.14 no.10
• /
• pp.1029-1034
• /
• 2004

Linear motion ( LM) guides having rolling elements have been used to position precision machines accurately. For ultra-accurate Positioning control of Precision machines, the understanding of the dynamic behavior of the LM guide at the macro and/or micro scales is most critical, but the research on this subject is rare. The objective of the present research is to investigate the vibration phenomena of the LM guide where balls are used as the rolling elements. Several experiments show the nonlinear characteristics of the LM guide such as hysteresis behavior and force-dependent natural frequencies phenomena.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2006.05a
• /
• pp.875-878
• /
• 2006

In the case of a vibration sensitive equipment, it require a vibration free environment to provide its proper function, therefore, it is very important to predict precisely vibration environment of microelectronics production facility due to adjacent blast work. However, it is not easy to evaluate a quantitative vibration response of structure due blast because it can be determined by the characteristics of vibration sources, propagation through rock and soil and dynamic properties of building. In this paper, vibration influence evaluation of micro-electronic Production building induced from adjacent blast activity was performed by real measurement data obtained on ground and structure at same time. And blast vibration allowable limit on ground was supposed by measurement data analysis in order to avoid operation error of precision equipments

• Journal of the Korean Society for Precision Engineering
• /
• v.14 no.5
• /
• pp.118-127
• /
• 1997

In this study, We use microstep control to reduce vibration of step motor. Microstep control of step motor is usually thought of as an extension of conventional step motor control technology. The essence of micro stepping is that we divide the full step of a step motor into a number of substep called microstep and cause the stepmotor to move through a substep per input pulse. In ideal case, by controlling the individual phase currents of a two-phase step motor sinusoidally we can get uniform torque and step angle. But due to the nonlinear characteristics of the step motor, we need to compensate current waveform to improve the over-all smoothness of the conventional micro stepping system. We implement digital Pulse Width Modul- ation (PWM) driver to drive step motor and microphone was used for detecting vibration. Driver enables speed change automatically by increasing or decreasing micro stepping ratio which we call Automatic Switching on the Fly. To compensate the torque harmonics, neural network is applied to the system and we found compensated optimal input current waveform. Finally we can get smooth motion of step motor in a wide range of motor speed.

• Structural Engineering and Mechanics
• /
• v.61 no.2
• /
• pp.193-207
• /
• 2017

In this study, the vibration of an electrostatically actuated micro cantilever beam is analyzed in which a viscoelastic layer covers a portion of the micro beam length. This proposed model is considered as the main element of mass and pollutant micro sensors. The nonlinear motion equation is extracted by means of Hamilton principle, considering nonlinear shortening effect for Euler-Bernoulli beam. The non-linear effects of electrostatic excitation, geometry and inertia have been taken into account. The viscoelastic model is assumed as Kelvin-Voigt model. The motion equation is discretized by Galerkin approach. The linear free vibration mode shapes of non-uniform micro beam i.e. the linear mode shape of the system by considering the geometric and inertia effects of viscoelastic layer, have been employed as comparison function in the process of the motion equation discretization. The discretized equation of motion is solved by the use of multiple scale method of perturbation theory and the results are compared with the results of numerical Runge-Kutta approach. The frequency response variations for different lengths and thicknesses of the viscoelastic layer have been founded. The results indicate that if a constant volume of viscoelastic layer is to be deposited on the micro beam for mass or gas sensor applications, then a modified configuration may be found by using the analysis of this paper.