• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2008년도 학술대회
• /
• pp.14-17
• /
• 2008

Recently, several advanced flow visualization techniques such as Particle Image Velocimetry (PIV) including stereo PIV, holographic PIV, and dynamic PIV have been developed. These advanced techniques have strong potential as the experimental technology which can be used for verifying numerical simulation. In addition, there would be indispensable in solving complicated thermo-fluid flow problems not only in the industrial fields such as automotive, space, electronics, aero- and hydro-dynamics, steel, and information engineering, but also in the basic research fields of medical science, bio-medical engineering, environmental and energy engineering etc. Especially, NT Nano Technology) and BT (Bio Technology) strongly demand these advanced measurement techniques, because it is difficult for conventional methods to observe most complicated nano- and bio-fluidic phenomena. In this paper, the basic principle of these advanced visualization techniques and their practical applications which cannot be resolved by conventional methods, such as flow in automotive HVAC system, ship and propeller wake, three-dimensional flow measurement in micro-conduits, and flow around a circulating cylinder will be introduced.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2008년 추계학술대회논문집
• /
• pp.14-17
• /
• 2008

Recently, several advanced flow visualization techniques such as Particle Image Velocimetry (PIV) including stereo PIV, holographic PIV, and dynamic PIV have been developed. These advanced techniques have strong potential as the experimental technology which can be used for verifying numerical simulation. In addition, there would be indispensable in solving complicated thermo-fluid flow problems not only in the industrial fields such as automotive, space, electronics, aero- and hydro-dynamics, steel, and information engineering, but also in the basic research fields of medical science, bio-medical engineering, environmental and energy engineering etc. Especially, NT (Nano Technology) and BT (Bio Technology) strongly demand these advanced measurement techniques, because it is difficult for conventional methods to observe most complicated nano- and bio-fluidic phenomena. In this paper, the basic principle of these advanced visualization techniques and their practical applications which cannot be resolved by conventional methods, such as flow in automotive HVAC system, ship and propeller wake, three-dimensional flow measurement in micro-conduits, and flow around a circulating cylinder will be introduced.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2003년도 춘계학술대회 논문집
• /
• pp.241-245
• /
• 2003

In this paper, a microassembly system based on hybrid manipulation schemes is proposed and applied to the assembly of a photonic component. In order to achieve both high precision and dexterity in microassembly, we propose a hybrid microassembly system with sensory feedbacks of vision and force. This system consists of the distributed 6-DOF micromanipulation units, the stereo microscope, and haptic interface for the force feedback-based microassembly. A hybrid assembly method, which combines the vision-based microassembly and the scaled teleoperated microassembly with force feedback, is proposed. The feasibility of the proposed method is investigated via experimental studies for assembling micro opto-electrical components. Experimental results show that the hybrid microassembly system is feasible for applications to the assembly of photonic components in the commercial market with better flexibility and efficiency.

• Restorative Dentistry and Endodontics
• /
• 제25권4호
• /
• pp.527-535
• /
• 2000

The purpose of this study was to evaluate effects of smear layer and dentin primers on the sealing ability of root canals. 126 extracted human teeth with single, straight canals and mature apices were used. The Samples were first classified into six groups as follows: presence of smear layer; absence of smear layer; Scotchbond Bond Multi-Purpose; All Bond 2; Mac Bond 2; Clearfil Liner Bond 2. A Positive control was also established. All teeth except the control group were then obturated with thermoplasticized gutta-percha and AH26. Electrochemical and dye penetration technique were later used to evaluate the degree of micro leakage through the root canal. Seventy teeth were then immersed in a 1% potassium chloride solution and An external power supply(DC 10 V) was then applied to the circuit for the electrochemical microleakage test. The degree of Microleakage was determined over period of 28 days before being evaluated. In total, 48 teeth were submitted to the dye infiltration technique. All specimen were suspended in 2% methylene blue dye for 1 week before being longitudinally split. The degree of dye infiltration was measured under a stereo microscope at ${\times}10$ magnification and evaluated. The results were as follows: 1. Apical microleakage increased throughout the test period in all group and one group having a smear layer showed a dramatic increase under electrochemical test (p<0.05). In the group having smear layer, the degree of apical microleakage was the highest, and the micro leakage was much higher than in the smear layer removed group in electrochemical test (p<0.05). Scotchbond Multi-Purpose, All Bond 2, Mac Bond 2 and Clearfil Liner Bond 2 showed lower micro leakage than one group having smear layer. The All Bond 2 and Clearfil Liner Bond 2 treated groups showed the lowest microleakage in electrochemical test (p<0.05). 2. There was no significant difference between the experimental groups in dye penetration technique. These results suggested that the removal of the smear layer from root canal and concomitantly the application of dentin primer into root canal could improve the sealing ability of root canal obturation.

• 천문학회보
• /
• 제37권2호
• /
• pp.120.1-120.1
• /
• 2012

The Lunar Reconnaissance Orbiter (LRO) launched on June 16, 2009 has six experiments including of the Cosmic Ray Telescope for the Effects of Radiation (CRaTER) onboard. The CRaTER instrument characterizes the radiation environment to be experienced by humans during future lunar missions. The CRaTER instrument measures the effects of ionizing energy loss in matter specifically in silicon solid-state detectors due to penetrating solar energetic protons (SEP) and galactic cosmic rays (GCRs) after interactions with tissue-equivalent plastic (TEP), a synthetic analog of human tissue. The CRaTER instrument houses a compact and highly precise microdosimeter. It measures dose rates below one micro-Rad/sec in silicon in lunar radiation environment. Forbush decrease (FD) event is the sudden decrease of GCR flux. We use the data of cosmic ray and dose rates observed by the CRaTER instrument. We also use the CME list of STEREO SECCHI inner, outer coronagraph and the interplanetary CME data of the ACE/MAG instrument.We examine the origins and the characteristics of the FD-like events in lunar radiation environment. We also compare these events with the FD events on the Earth. We find that whenever the FD events are recorded at ground Neutron Monitor stations, the FD-like events also occur on the lunar environments. The flux variation amplitude of FD-like events on the Moon is approximately two times larger than that of FD events on the Earth. We compare time profiles of GCR flux with of the dose rate of FD-like events in the lunar environment. We figure out that the distinct FD-like events correspond to dose rate events in the CRaTER on lunar environment during the event period.

• Restorative Dentistry and Endodontics
• /
• 제19권2호
• /
• pp.473-484
• /
• 1994

To investigate the effect of resin cement, which had been known to increase the adhesive capacity of the cast gold inlay, on the gingival marginal fit and whether the tin-planting of the beveled area affects the marginal fit, Class II cast gold inlays were made on the 25 sound molars. Control group(ZPC goup) was cemented with the ZPC by conventional method. Experimental groups were cemented with the resin cement(Super-hond & $Panavia_{EX}$) and subdivided further by the existence or nonexistence of the tin-plating of the beveled area(ST & PT groups: with plating, SNT & PNT groups: without plating). So, each group was consisted of 5 teeth and the gingival margin of each specimen was mesiodistally sectioned by 3 times and the marginal and internal gap were evaluated by the Stereo Microscope (${\times}180$) and the Scanning Electron Micrascope(${\times}5,000$) was used for examining the adhesive relationship of the resin cement to the cavity wall and to the cast gold surface. The results were as follows : 1. Marginal gap was less than internal gap in all groups. 2. ZPC and SNT(bevel without tin-plating) groups showed the least gap and gap in PNT(bevel without tin-plating) group, ST(bevel with tin-plating) group, PT(bevel with tin-plating) group showed the greater value in order in evaluation of the both internal gap and marginal gap. 3. With the exception of the relationships between ZPC and SNT groups, ST and PNT groups, relationships between any other groups showed the statistical significance in the internal gap(p<0.05). 4. In the marginal gap, all relationships between groups showed the statistical significance (p<0.05) except the relationships between ZPC and SNT groups, ST and PNT groups, ZPC and PNT groups. 5. ZPC group showed more soluble phenamena than the resin groups(ST, SNT, PT, PNT). 6. Resin cement showed the void spaces in spite of good penetration into the micro-irregularities on both the tooth surface and the cast surface. The void was shown more in PT and PNT groups than in the ST and SNT groups. 7. After the treatment of heat and desiccation for SEM specimen, resin cements were detached more easily from the tooth surface than from the cast surface.

• 한국자원식물학회:학술대회논문집
• /
• 한국자원식물학회 2019년도 춘계학술대회
• /
• pp.64-64
• /
• 2019

In order to evaluate the taxonomical relevance of seeds morphological characteristics, a macroand micro-morphological study was conducted on seeds of Korean Vicia (Fabacea). We collected 19 taxa of genus Vicia distributed in Korea and introduced one taxa from USDA. The morphological characteristic and testa texture of seeds were investigated using a Stereo-microscope (SM) and Scanning Electron Microscope (SEM). Most of Vicia seeds were found spherical or oblong and some seeds were oval and subglose. The largest seed was V. chosenensis ($4.3{\times}3.6{\times}2.6mm$), and the smallest was V. teterasperma ($1.7{\times}1.7{\times}1.5mm$). V. chosenensis and V. hirsuta were separated from other Vicia species by having a shiny in seed finish. In hilum shape, 14 species have linear and V. sepium was distinguished by having a circumlinear. In testa texture, they developed papilae, only V. hirsuta has lophate in level type. Deposition of the sheet-like debris between the papilae was observed in V. chosenensis, V. cracca, and V. unijuga. Polymorphism information content (PIC) values of the 13 qualitative morphological characters (QMC) were in the range of 0.0950 to 8863 with an average of 0.4611. PIC value of seed shape, seed colour, hilum colour were 0.7403, 0.8177, 0.883 respectively. Cluster analysis based on QMC detected three main clades. V. cracca, V. amurensis, V. amoena were involved in Group 1 and V. unijuga f. minor, V. unijuga, V. unijuga f. angustifolia, V. sepium, V. hirticalycina, V. hirsuta, V. linearfolia, V. chosenensis, V. pseudorobus, V. venosa var. cuspidata were involved in Group 2. V. nipponica, V. japonica, V. villosa, V. dasicarpa, V. bungei, V. angustifolia, V. tetrasperma were clustered in Group 3. Our research suggests that morphological characteristic and testa texture of seeds could be used as definers for the identification of genus Vicia.

• 박물관보존과학
• /
• 제26권
• /
• pp.67-82
• /
• 2021

국립부여박물관 소장 금제구슬 2점(부여5336)은 1993년 부여 능산리 공방터 주변에서 발견된 것으로 백제 시대에 제작된 누금제품이라는 희소성과 완형의 형태를 갖추고 있어 제작기법을 살펴볼 수 있는 매우 중요한 자료이다. 본 연구에서는 이동형 엑스선형광분석기와 실체현미경 및 분광분석기 부착 주사전자현미경 분석을 통해 금제구슬의 성분 조성을 확인하고 미세 형태와 표면 상태 관찰, 접합 부위 성분 분석을 통해 제작 기법을 살펴보았다. 금제구슬은 속이 비어있는 형태로 구멍을 뚫은 뒤 그 주변을 금선으로 둘러 장식하였으며 나머지 부분을 금알갱이로 장식하였다. 일부에서 금알갱이를 먼저 금판에 접합하고 금알갱이 위에 금선이 올라간 형태를 확인할 수 있었으며 금선과 금알갱이 모두 23.6K~23.7K로 분석되었다. 누금의 접합 부위 일부에서는 구리의 함량이 높게 검출되었으며 재현 실험 및 제작 방법 연구 결과를 참고로 하여 볼 때 구리확산법을 사용하여 제작한 것으로 추정된다.