• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.42 no.3
• /
• pp.417-425
• /
• 2022

Interest in micro cars is growing around the world, and policy support for micro cars has been increasing in Korea. It is important to meet minimum safety standards for the operation of micro cars on roads due to concerns around micro car safety and the limited driving range of micro cars. In this study, visibility experiments that included safety identification of micro cars were conducted to try and prevent a decrease in driver reaction time. Safety identification lights were installed to the rear of a micro car, and the visibility and discomfort of the vehicle were evaluated to determine whether the micro car was safe to drive on an expressway. As a result, the installation effect of Micro car which install safety identification lamp was found when joining the point at an acceleration lane of the grade separation intersection, and that light on/off could be effective when entering an expressway. If the micro car operation plan proposed in this study is applied, the safety of micro cars on expressways can be increased by improving the visibility of micro car.

• Proceedings of the KIPE Conference
• /
• 1998.07a
• /
• pp.48-53
• /
• 1998

This paper describes on the development of Controller for the Utility Car using Microprocessor. The Utility Car is composed of Controller, separately exited DC motor, battery and potbox. It is easier to for a digitalized controller using microprocessor append new function than an analogized controller. The test driving of controller shows that the Utility Car travels 20 [km] per charge.

• Proceedings of the KIEE Conference
• /
• 2002.04a
• /
• pp.34-36
• /
• 2002

This paper addresses an elevator position control scheme in unified control system. Conventional systems have employed independent micro-processors for speed, car, and group control respectively and the car controller generates a velocity command by combining the time-based and distance-based velocity pattern. In this scheme, it is inevitable that an elevator creeps in the vicinity of target floor, or stops abruptly. The proposed control system employs only one high-performance micro-processor, which can execute the car and group control as well as the speed control. It simply generates the desired position trajectory based on time and on-line corrects a velocity pattern to make the position error be zero. Experimental results show the feasibility of the proposed control scheme.

• Transactions of the Korean hydrogen and new energy society
• /
• v.20 no.1
• /
• pp.64-72
• /
• 2009

In order to convert efficiently vibration energy of a car tire wheel into electrical power by using piezoelectric materials, the design of the materials must be performed for the dynamic characteristics of the piezoelectric materials to be matched with them of the vibration energy sources well. An accelerometer was installed on the tire wheel with a slip ring to investigate the dynamic mode of the wheel as one of the vibration energy sources. During road test, the measurement on the vibration mode of the tire wheel was performed with variations of car speed and road condition. The experimental data were analyzed details for availability as a micro power source for wireless TPMS(Tire Pressure Monitoring System).

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.12 no.1
• /
• pp.70-76
• /
• 2013

Recently, the performance and function of electrical and electronic system in automotive vehicles is developing at a rapid rate with the advancement of IT technologies. Combined together with micro-controller and sensor technologies, the Vehicle Smart System (VSS) being developed to improve driver's convenience and comfort has been employed to a variety of applications. In addition to the convenience system, the Auto-parking Assistance System (AAS) that is now attracting a new attention has been already applied to some vehicles, but it is currently limited to luxury car models only. In this paper, we present a fuzzy controller that enables autonomous parking assistance without the AAS. The controller can perform the assistance with information provided from moving status, current position and steering angle as one is able to park a car based on his/her experience and knowledge for driving and parking. We have evaluated its performance of the proposed controller by simulation and tested the excellence of the controller by building a model vehicle embedded with the micro-controllers.

• Journal of Welding and Joining
• /
• v.33 no.4
• /
• pp.44-49
• /
• 2015

The structural epoxy adhesive used in car body assembly needs the highest level of joint mechanical strength under lap shear, T-peel and impact peel conditions. In this study, the effect of nano functionalized block copolymer addition on the impact peel strength of epoxy adhesive was investigated. DSC analysis showed that the addition of nano functionalized block copolymer did not affect the curing reaction of epoxy adhesive. From single lap shear test, it was found out that the addition of nano functionalized block copolymer slightly decreased the cohesive strength of cured adhesive layer. The addition of nano functionalized block copolymer showed beneficial effect on T-peel strength by changing the adhesive failure mode to the mixed mode. However, the addition of nano functionalized block copolymer just decreased the room temperature impact peel strength. It was considered that the addition of nano functionalized block copolymer could have effect on disturbing the crack propagation only for the case of slow strain rate.

• Analytical Science and Technology
• /
• v.24 no.4
• /
• pp.290-297
• /
• 2011

In present, evaluation method for car cabin air quality has been developed in ISO, China, Japan. Also The management standard for new produced car has been applied since 1, July, 2010. To manage car cabin air quality, It is important to evaluate VOC emitted from interior material. In this study, complete component of door trim armrest was evaluated in accordance with ISO 12219-5, cut component was evaluated in accordance with ISO 12219-3. The vapour gas was collected with stainless tube packed with Tenax TA and analyzed with TD-GC/MS. It was confirmed that emission rate of each compounds was difficult in each evaluation method. As a result, to evaluating each components composing door trim armrest, main sources of emitting VOCs in door trim armrest were PP substrate and adhesive.

• Journal of Welding and Joining
• /
• v.31 no.5
• /
• pp.71-76
• /
• 2013

The effect of zirconate having - NH functional group on the T-peel and lap shear strength of $CaCO_3$ containing structural epoxy adhesive for car body assembly was investigated. Curing behavior of epoxy adhesive samples were investigated by differential scanning calorimeter (DSC) techniques. The addition of zirconate up to 7.5 phr did not affect the curing mechanism of epoxy adhesive. While the small amount of zirconate addition less than 1.1 phr increased the cross-linking density, the excess addition of zirconate resulted in the increase of uncross-linked impurity. From the increase of T-peel and lap shear strength and the change of fracture mode from the adhesive failure to the mixed one, it was considered that the small addition of zirconate was effective in improving the adhesion strength of epoxy adhesive to the adherend and inorganic filler surfaces. The formation of uncross-linked impurity with the excess addition of zirconate was considered to decrease the joint strength by decreasing the cohesive strength of the cured epoxy.

• International Journal of Control, Automation, and Systems
• /
• v.3 no.3
• /
• pp.461-468
• /
• 2005

This paper proposes a wheel-assembly automation system, which assembles a wheel into a hub of a vehicle hung to a moving hanger in a car manufacturing line. A macro-micro manipulator control strategy is introduced to increase the system bandwidth and tracking accuracy to ensure insertion tolerance. A camera is equipped at the newly designed wheel gripper, which is attached at the center of the end-effector of the macro-micro manipulator and is used to measure position error of the hub of the vehicle in real time. The redundancy problem in the macro-micro manipulator is solved without complicated calculation by assigning proper functions to each part so that the macro part tracks the velocity error while the micro part regulates the fine position error. Experimental results indicate that tracking error satisfies the insertion tolerance of assembly $({\pm}1mm)$, and thus it is verified that the proposed system can be applied to the wheel assembly task on a moving hanger in the manufacturing line.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.738-742
• /
• 2005

Rapid Prototype has been used to design and Production of part in a variety of fields ; Car, Electronic products, Aviation, Heavy industry etc. Moreover development of hardware gave rise to use the method of Rapid Prototype more and more at high precision and complicated shapes. Expecially, to be using process of products that shapes of Micro-hole ; Cellular phones, Antennas, Jewels, Semi conductor cases. In case of Micro-shape, precision of the shape turns on various condition ; Laser size, Laminate height, scanning speed, overcure, viscosity of resin, etc. Sometimes breaks out the case that interner hole of shape is blocked by viscosity of resin. The phenomenon has solved easily to reduce viscosity of resin. But, in case of the method brings about the problem that strength goes down in actuality products hardening. This study on verify to change of shape of Micro-hole and makes the semiconductor case which has shape of Micro-hole by using resin of higher viscosity, scanning speed and overcure