• 한국해양공학회지
• /
• 제1권1호
• /
• pp.127-137
• /
• 1987

The evaluation of the elastic-plastic fracture toughness $J_{1C}$ was performed on the center of weld metal(CWM), the heat affected zone (HAZ) and the base metal (BM) of API 5LB steel pipes welded by the high frequency electric resistance welding. The $J_{1C}$ was evaluated by the JSME R-Curve and JSME SZW methods using the smooth and side-grooved specimens. The results are as follows; (1) The $J_{1C}$ values by the SZW method are overestimated as compared with those by the R-curve method, because the micro-crack is formed as SZW increase with the deformation at SZ after initiation of the ductile crack. (2) The everage of $J_{1C}$ values by the the R-curve and the SZW methods in side-grooved specimens tended to decrease in comparison with smooth specimens 9.42% at CWM, 4.2% at HAZ, 23.2% at BM, respectively. (3) The boundary of the fatigue pre-crack, stretched zone, and dimple regions appeared more clearly in side-grooved specimens, for the slight change of SZW in the direction of the plate thickness, as compared with smooth specimens.

• International Journal of Railway
• /
• 제1권3호
• /
• pp.106-112
• /
• 2008

Rolling-sliding, cyclic contact of wheel and rail progressively alters the microstructure of the contacting steels, eventually leading to micro-scale crack initiation, wear and macro-scale crack growth in the railhead. Relating the microstructural changes to subsequent wear and cracking is being accomplished through modelling at three spatial scales: (i) bulk material (ii) multi-grain and (iii) sub-grain. The models incorporate detailed information from metallurgical examinations of used rails and tested rail material. The initial 2-dimensional models representing the rail material are being further developed into 3-dimensional models. Modelling is taking account of thermal effects, and traffic patterns to which the rails are exposed.

• 한국가스학회지
• /
• 제17권1호
• /
• pp.19-25
• /
• 2013

용접에 의한 가스설비, 교량, 선박 등 강 구조물의 접합 방법은 대부분 십자형이나 T형의 필릿 용접으로 이루어지며 구조물의 형상과 용도에 따라 완전 용입 또는 불완전 용입 상태로 이루어진다. 본 연구에서는 십자형 필릿용접 구조물에 대하여 재료 두께별 용입 깊이에 따른 피로 균열 특성을 파악하였고, 그 결과로부터 무한수명 영역내에서의 안전 설계응력에 대하여 고찰하였다. 미 용입 길이가 길면 루트 부 파괴가 되어 무한 수명 영역은 작고 미 용입 길이가 짧으면 토우부 파괴가 되어 무한 수명 영역은 크게 나타났다. 3층 용접한 재료 두께 20mm의 경우가 2층 용접한 재료 두께 10mm, 15mm의 경우보다 미세한 페라이트 침상 조직을 더 많게 형성시켜 노치 인성을 증가시키므로 서 피로강도와 무한 수명을 더 향상시킨 것으로 나타났다.

• 대한치과보철학회지
• /
• 제46권3호
• /
• pp.298-306
• /
• 2008

STATEMENT OF PROBLEM: Effect of surface treatment of ceramic under loading does not appear to have been investigated. PURPOSE: The aim of this study was to investigate the effect of surface treatment of esthetic ceramic, which is performed to increase the bonding strength, on the fracture stress under controlled cyclic loading condition. MATERIAL AND METHODS: Sixty 1.0 mm-thick specimens were made from Mark II Vitablocs (Vita Zahnfabrik, Germany) and divided into 3 groups: polished (control), sandblasted, and etched. Specimens of each group were bonded to a dentin analog material base including micro-channels to facilitate the flow of water to the bonding interface. Bonded ceramics were cyclically loaded with a flat-end piston in the water (500,000 cycles, 15Hz). Following completion of cyclic loading, specimens were examined for subsurface crack formation and subsequent stress was determined and loaded to next specimen by the staircase method according to the crack existence. RESULTS: There were significant differences of mean fatigue limit in the sandblasted (222.86 ${\pm}$ 23.42 N) and etched group (222.86 ${\pm}$ 14.16 N) when compared to polished group (251.43 ${\pm}$ 10.6 N) (P<.05; Wald-type pair-wise comparison and post hoc Bonferroni test). Of cracked specimens, surface treated group showed longer crack propagation after 24 hours. All failures originated from the radial cracking without cone crack. Fracture resistance of this study was very low and comparable to failure load in the oral cavity. CONCLUSION: Well controlled cyclic loading could induce clinically relevant cracks and fracture resistance of Mark II ceramic was relatively low applicable only to anterior restorations. Surface treatment of inner surface of feldspathic porcelain in the matsicatory area could influence lifetime of restorations.

• Journal of Welding and Joining
• /
• 제27권1호
• /
• pp.102-107
• /
• 2009

Weldability of Mg alloy was investigated using servo-actuated DC resistance spot welder. Due to its uncommon electrical and mechanical properties, lots of voids and cracks were observed inside nugget with conventional weld schedule. Lobe curve was proposed to clarify proper electrode force and weld current, which guarantee reasonable weld strength and fatigue life. Macro structure of sectioned specimen was examined to count total number of void and crack. Post weld schedule is also proposed to reduce micro victors hardness value of weld zone.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2005년도 추계학술대회 논문집
• /
• pp.344-349
• /
• 2005

Cast steels have been mainly in rod type couplers which connect railway vehicles. These components, as important members, are exposed to repeat to repeated stresses and impact loading during stop and departure service for a long tie. The coupler suffers fatigue crack initiations and demage that cause need to repair weldment due to these loading conditions. Therefore, the heat affected zone of cast steel couple in rod type were evaluated in view of metallurgical weld characteristics after repair welding at laboratory. The specimens with two different welding techniques were evaluated after several welding conditions and post-heat treatments. Micro-vickers hardness and tensile tests and microstructural observations were conducted on heat affected zone of the weldment according to repair weld and post-heat treatment.

• Smart Structures and Systems
• /
• 제29권6호
• /
• pp.799-805
• /
• 2022

Permanent magnet synchronous motors (PMSMs) are widely used in systems requiring high control precision, efficiency, and reliability. Predicting the remaining useful life (RUL) with health monitoring of PMSMs prevents catastrophic failure and ensures reliable operation of system. In this study, a model-based method for predicting the RUL of PMSMs using phase current and vibration signals is proposed. The proposed method includes feature selection and RUL prediction based on a particle filter with a degradation model. The Paris-Erdogan model describing micro fatigue crack propagation is used as the degradation model. An experimental set-up to conduct accelerated life test, capable of monitoring various signals was designed in this study. Phase current and vibration data obtained from an accelerated life test of the PMSMs were used to verify the proposed approach. Features extracted from the data were clustered based on monotonicity and correlation clustering, respectively. The results identify the effectiveness of using the current data in predicting the RUL of PMSMs.

• 대한기계학회논문집
• /
• 제11권5호
• /
• pp.717-724
• /
• 1987

본 연구에서는 한국중공업에서 실제로 제작한 터어빈 로우터를 시험편으로 하 여 -150.deg. C에서 +150.deg. C에 걸쳐 인장시험, 충격시험 및 파괴인성시험을 실시하여 각 온 도에서 기계적 성질과 파괴인성치를 시험적으로 구하고 Begley-Logsdon의 방법에 따라 파괴인성치를 예측하여 예측방법의 유용성 여부를 조사하고 또한 파단면의 양상을 함 께 검토하였다.

• 비파괴검사학회지
• /
• 제29권5호
• /
• pp.450-457
• /
• 2009

열차폐 코팅 시편에 대하여 열충격을 주기적으로 가한 후 발생하는 결함을 관찰하였다. 실험에 사용 된 열차폐 코팅 시편은 인코넬-738로 제작된 모재 위에 CoNiCrAlY 본드 코팅층과 $ZrO_2-8wt%Y_2O_3$ 세라믹탑 코팅층이 플라즈마 용사 방법으로 올려진 형태로 되어있다. 열충격 시험은 $1000^{\circ}C$의 고온으로 가열했다가 상온으로 급격하게 냉각시키는 가혹한 조건으로 실행되었고, 사이클 수가 증가함에 따라 열충격의 피로도 또한 증가하였다. 시험후 시편 내부의 미세 조직 변화와 결함을 전자현미경으로 관찰하고, 시편의 기계적인 특성을 측정하여 그 변화 양상을 살펴보았다. 열충격 주기실험후 본드 코팅층과 세라믹 탑 코팅층 사이에 발생하는 TGO 산화물층에 대한 변화 양상과 이에 대한 와전류 신호를 측정하여 TGO층 성장 거동의 비파괴적인 평가를 위한 실험을 진행하였다. 본 연구를 통하여 마이크로 단위의 TGO층에 대한 와전류검사의 적용 가능성을 확인하고 열차폐 코팅의 수명을 예측할 수 있는 가능성을 제시하였다.