• Korean Journal of Materials Research
• /
• v.4 no.8
• /
• pp.847-854
• /
• 1994

An amorphous single phase and coexistent amorphous and hcp-Mg phases in Mg-Zn-Ce system were found to form in the composition ranges of 20 to 40% Zn, 0 to 10% Ce and 5 to 20% Zn, 0 to 5% Ce, respectively. A $Mg_{85}Zn_{12}Ce_{3}$ amorphous alloy containing nanoscale hcp-Mg particles was found to form either by melt spinning or by heat treatment of melt -spun ribbon. The particle size of the hcp-Mg phase can be controlled in the range of 4 to 20 nm. The mixed phase alloy prepared thus has a good bending ductility and exhibits high ultimate tensile strength($\sigma_{B}$) ranging from 670 to 930 MPa and fracture elongation($\varepsilon_{f}$) of 5.2 to 2.0%. The highest specific strength($\sigma_{B}$/density =$\sigma_{s}$)$3.6 \times 10^5N \cdot m/kg$. It should be noted that the highest values of flB, US and ？1 are considerably higher than those (690MPa,$2.5 \times 10^5N \cdot m/kg$and 2.5%) for amorphous Mg-Zn-Ce alloys. The increase of the mechanical strengths by the formation of the mixed phase structure is presumably due to a dispersion hardening of the hcp supersaturated solution which has the hardness higher than that of the amorphous phase with the same composition.

• Journal of the Korean Society for Heat Treatment
• /
• v.22 no.2
• /
• pp.75-79
• /
• 2009

Precipitate formations and grain size variations in various Mg-Sn-Zn alloys have been investigated and their effects on the tensile properties and sheet metal formability were evaluated. MgSn and MgZn precipitates were observed in the alloy sheets, however any clear difference in morphology or size for the precipitates could not be found even though MgSn precipitates tend to be larger than MgZn. The highest formability in terms of conical cup value was found in the Mg-4 wt%Sn-2 wt%Zn where the high tensile elongation and the reduced grain coarsening at elevated temperatures were observed.

• Journal of Korea Foundry Society
• /
• v.37 no.3
• /
• pp.63-70
• /
• 2017

In the present study, effects of an addition of Sn on the microstructure and corrosion behavior were investigated in Mg-4%Zn-(0-3)%Sn casting alloys. With an increase in the Sn content, the ${\alpha}-(Mg)$ dendritic cell size was reduced, whereas the total amount of precipitates increased due to the formation of the $Mg_2Sn$ phase. It was found in immersion and electrochemical corrosion tests that the addition of Sn has a detrimental effect on the corrosion resistance of the Mg-4%Zn alloy. Microstructural examinations of the corrosion product and the corroded surface indicated that an accelerated micro-galvanic effect by the $Mg_2Sn-phase$ particles and a less protective corrosion product on the surface were responsible for the increased corrosion rate at a higher Sn content.

• Journal of Powder Materials
• /
• v.14 no.2 s.61
• /
• pp.140-144
• /
• 2007

Using Spark Plasma Sintering process (SPS), consolidation behavior of gas atomized $Mg_{97}Zn_1Y_2$ alloys were investigated via examining the microstructure and evaluating the mechanical properties. In the atomized ahoy powders, fine $Mg_{12}YZn$ particles were homogeneously distributed in the ${\alpha}-Mg$ matrix. The phase distribution was maintained even after SPS at 723 K, although $Mg_{24}Y_5$ particles were newly precipitated by consolidating at 748 K. The density of the consolidated bulk Mg-Zn-Y alloy was $1.86g/cm^3$. The ultimate tensile strength (UTS) and elongation were varied with the consolidation temperature.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 1996.11a
• /
• pp.24-25
• /
• 1996

• Journal of Korea Foundry Society
• /
• v.19 no.1
• /
• pp.7-14
• /
• 1999

• Proceedings of the Materials Research Society of Korea Conference
• /
• 1997.05a
• /
• pp.75-75
• /
• 1997

• Journal of Korea Foundry Society
• /
• v.13 no.2
• /
• pp.168-174
• /
• 1993

It has been known that the grain refinement of Cu base alloys greatly improved mechanical properties, castability, workability and hot shortness resistance etc. In this study CuZr50, CuP7, CuFe7, CuMg10 binary alloys were added as grain refiners in CuZn36 alloy. The alloys melted in vacuum and controlled in mixed gas conditions and casted at $1050^{\circ}C$. Zr-P-X compound has significantly grain refined but oxygen has been found detrimental to grain refinement. In the case of Zr /B ratio below 4, B acted as grain growth element in this alloy.

• Korean Journal of Materials Research
• /
• v.30 no.10
• /
• pp.542-549
• /
• 2020

Effects of Sc addition on microstructure, electrical conductivity, thermal conductivity and mechanical properties of the as-cast and as-extruded Al-2Zn-1Cu-0.3Mg-xSc (x = 0, 0.25, 0.5 wt%) alloys are investigated. The average grain size of the as-cast Al-2Zn-1Cu-0.3Mg alloy is 2,334 ㎛; however, this value drops to 914 and 529 ㎛ with addition of Sc element at 0.25 wt% and 0.5 wt%, respectively. This grain refinement is due to primary Al₃Sc phase forming during solidification. The as-extruded Al-2Zn-1Cu-0.3Mg alloy has a recrystallization structure consisting of almost equiaxed grains. However, the as-extruded Sc-containing alloys consist of grains that are extremely elongated in the extrusion direction. In addition, it is found that the proportion of low-angle grain boundaries below 15 degree is dominant. This is because the addition of Sc results in the formation of coherent and nano-scale Al₃Sc phases during hot extrusion, inhibiting the process of recrystallization and improving the strength by pinning of dislocations and the formation of subgrain boundaries. The maximum values of the yield and tensile strength are 126 MPa and 215 MPa for the as-extruded Al-2Zn-1Cu-0.3Mg-0.25Sc alloy, respectively. The increase in strength is probably due to the existence of nano-scale Al₃Sc precipitates and dense Al₂Cu phases. Thermal conductivity of the as-cast Al-2Zn-1Cu-0.3Mg-xSc alloy is reduced to 204, 187 and 183 W/MK by additions of elemental Sc of 0, 0.25 and 0.5 wt%, respectively. On the other hand, the thermal conductivity of the as-extruded Al-2Zn-1Cu-0.3Mg-xSc alloy is about 200 W/Mk regardless of the content of Sc. This is because of the formation of coherent Al₃Sc phase, which decreases Sc content and causes extremely high electrical resistivity.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2015.05a
• /
• pp.126-127
• /
• 2015

주방 상태의 Mg, Mg+5wt%.Ca, Mg+5wt%.Ca+1wt%.Zn 합금의 발화 실험 및 TGA를 통해 $450{\sim}600^{\circ}C$에서 고온산화실험을 실시하였다. Ca의 첨가로 내발화성 및 고온산화특성이 향상되었으며, Zn의 첨가는 내발화성과 고온산화특성 모두에 악영향을 미쳤다. 산화시킨 시편의 SEM/EDS, XRD, 및 TEM 분석을 통하여 고온산화 특성을 조사하였다.