• Journal of Advanced Marine Engineering and Technology
• /
• 제31권4호
• /
• pp.394-400
• /
• 2007

The properties and weldability of lap joints by PFSW with 1050 Al sheet was investigated according to tool shape. dimension and welding condition. Tensile shear test was carried out for lap jointed specimen, and the hardness in the joint regions was examined. Moreover interfacial joining length, metallograph and failure location of the lap-jointed cross section were discussed. Two tool types were a simple cylindrical type and a notched cylindrical type. Under joining conditions such as plunging depth of 2.2mm. rotating speed of 1600rpm and dwelling time of 3s, the tensile shear strength of lap-jointed specimen by the notched type tool was superior to that by simple cylindrical type tool. The maximum tensile shear load of lap jointed specimen was 5807N. Optimal dimensions of the notched type tool were as follows : diameters of the shoulder and pin were $18{\phi}mm$ and $10{\phi}mm$, and pin length was 2.2mm.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 하계학술대회 논문집
• /
• pp.398-401
• /
• 2002

When the current flows over the allowable current due to the overload, it causes electric disaster such as an electrical fire and an electric shock by short current or leakage of electricity because the covering is deteriorated according to the heating action. In this paper, for the wire(IV 1.6mm) used as interior wiring, we analyzed a variation of the surroundings temperature, the form and the structure of a covering, and the crystal structure of a conductor. In the result of this experiment, the surroundings temperature at the allowable current of 300% rose to about 47$^{\circ}C$, and it rose up to the maximum allowable temperature of the wire at 400%. Consequently, it was broken within one minute at 500%. In the analysis of a metallograph, the conductor broken by the over current showed the dendrite. These analyses result will be applied to judging the electrical fire.

• 전기학회논문지P
• /
• 제57권3호
• /
• pp.332-337
• /
• 2008

We analyzed carbonization pattern and crystal structure of polyvinyl chloride wire by thermal stress. Copper that is oxidized at normal temperature is a reddish brown. If under the thermal stress range of 500 to 700 [$^{\circ}C$], carbonization and exfoliation occurrence. Section structure of electric wire is same as arrangement of particle in metallograph analysis. But, as thermal stress increases, size of particle is enlarged. Electric wire displays elongation structure in SEM image analysis and elongation structure collapses when receive thermal stress at 300 [$^{\circ}C$]. In EDX analysis, we get the spectra of CuL, CuK, OK, and ClK. FT-IR analysis was shown new spectra with in range of $1,440{\sim}1,430\;[cm^{-1}]$, 1,340 [$cm^{-1}$], 1,240 [$cm^{-1}$].

• 대한소아치과학회지
• /
• 제6권1호
• /
• pp.7-13
• /
• 1979

To evaluate the surface roughness of subgingival area of S. P. crown margins subjected to various polishing procedures, the study was performed by use of metallograph and surface roughness tester. The following results were obtained; 1) Abrasive stone wheel produced the roughest surface ($16.0{\mu}m$). 2) Final polish with rouge after polishing with rubber wheel, subsequent to abrasive stone wheel, produced the smoothest surface ($0.3{\mu}m$). 3) Both polish with rubber wheel after polshing with abrasive stone wheel, and polish with pumice (coarse$\rightarrow$medium$\rightarrow$fine) produced same surface roughness ($0.8{\mu}m$).

• 한국결정성장학회지
• /
• 제4권2호
• /
• pp.148-156
• /
• 1994

$YBa_2Cu_3O_X$상 부근의 3가지 조성을 skull melting 방법으로 4MHz에서 녹인 후 방향적 결정성장을 시켰다. 일반적인 무기재료 공정방법으로 처리된 분말을 skull에 넣은 후 $1200^{\circ}C$부근에서 용융시켰다. 사용한 성장속도는 4~0.25 cm/hr이었으며, 금속현미경, X-선 회절기, EDX 등을 이용해서 제조된 시편을 조사하여 사용한 분말의 조성에 따른 시편의 미세조직의 변화를 관찰하였다. $YBa_2Cu_7O_X$와 $YBa_5Cu_{11}O_X$ 시편의 대표적인 미세조직은 성장방향으로 자라난 침상형태의 $YBa_2Cu_3O_X$와 $Y_2BaCuO_5$ 상이 $CuO-BaCuO_2$의 공융 조직상 사이에 생성된 것으로 나타났다.