• Journal of Advanced Marine Engineering and Technology
• /
• v.31 no.4
• /
• pp.394-400
• /
• 2007

The properties and weldability of lap joints by PFSW with 1050 Al sheet was investigated according to tool shape. dimension and welding condition. Tensile shear test was carried out for lap jointed specimen, and the hardness in the joint regions was examined. Moreover interfacial joining length, metallograph and failure location of the lap-jointed cross section were discussed. Two tool types were a simple cylindrical type and a notched cylindrical type. Under joining conditions such as plunging depth of 2.2mm. rotating speed of 1600rpm and dwelling time of 3s, the tensile shear strength of lap-jointed specimen by the notched type tool was superior to that by simple cylindrical type tool. The maximum tensile shear load of lap jointed specimen was 5807N. Optimal dimensions of the notched type tool were as follows : diameters of the shoulder and pin were $18{\phi}mm$ and $10{\phi}mm$, and pin length was 2.2mm.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.07a
• /
• pp.398-401
• /
• 2002

When the current flows over the allowable current due to the overload, it causes electric disaster such as an electrical fire and an electric shock by short current or leakage of electricity because the covering is deteriorated according to the heating action. In this paper, for the wire(IV 1.6mm) used as interior wiring, we analyzed a variation of the surroundings temperature, the form and the structure of a covering, and the crystal structure of a conductor. In the result of this experiment, the surroundings temperature at the allowable current of 300% rose to about 47$^{\circ}C$, and it rose up to the maximum allowable temperature of the wire at 400%. Consequently, it was broken within one minute at 500%. In the analysis of a metallograph, the conductor broken by the over current showed the dendrite. These analyses result will be applied to judging the electrical fire.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.57 no.3
• /
• pp.332-337
• /
• 2008

We analyzed carbonization pattern and crystal structure of polyvinyl chloride wire by thermal stress. Copper that is oxidized at normal temperature is a reddish brown. If under the thermal stress range of 500 to 700 [$^{\circ}C$], carbonization and exfoliation occurrence. Section structure of electric wire is same as arrangement of particle in metallograph analysis. But, as thermal stress increases, size of particle is enlarged. Electric wire displays elongation structure in SEM image analysis and elongation structure collapses when receive thermal stress at 300 [$^{\circ}C$]. In EDX analysis, we get the spectra of CuL, CuK, OK, and ClK. FT-IR analysis was shown new spectra with in range of $1,440{\sim}1,430\;[cm^{-1}]$, 1,340 [$cm^{-1}$], 1,240 [$cm^{-1}$].

• Journal of the korean academy of Pediatric Dentistry
• /
• v.6 no.1
• /
• pp.7-13
• /
• 1979

To evaluate the surface roughness of subgingival area of S. P. crown margins subjected to various polishing procedures, the study was performed by use of metallograph and surface roughness tester. The following results were obtained; 1) Abrasive stone wheel produced the roughest surface ($16.0{\mu}m$). 2) Final polish with rouge after polishing with rubber wheel, subsequent to abrasive stone wheel, produced the smoothest surface ($0.3{\mu}m$). 3) Both polish with rubber wheel after polshing with abrasive stone wheel, and polish with pumice (coarse$\rightarrow$medium$\rightarrow$fine) produced same surface roughness ($0.8{\mu}m$).

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.4 no.2
• /
• pp.148-156
• /
• 1994

Three composition in the system of $YO_{1.5}-BaO-CuO$ were grown using a cold crucible (skull) melting technique with a 50 kW R.F. induction generator operating at 4 MHz as the power source. The starting materials were prepared by conventional ceramic powder processing methods, loaded into the skull, and melted at about $1200^{\circ}C$. For this study, compositions near the $YBa_2Cu_3O_X$ region were selected. The growth rates used ranged from 4 cm/hr to 0.25 cm/hr. The relation between the microstructures and the starting composition of each ingot was determined using metallograph, X-ray diffraction, and energy dispersive X-ray analysis. Both $YBa_2Cu_3O_X$ and $Y_2BaCuO_5$ needle-shaped crystals, aligned with the growth direction, were formed in the $CuO-BaCuO_2$ eutectic matrix of the $YBa_2Cu_7O_x and YBa_5Cu_{11}O_x$ ingot.