• ETRI Journal
• /
• v.30 no.4
• /
• pp.600-602
• /
• 2008

A very small patch-type RFID tag antenna (UHF band) using ceramic material mountable on metallic surfaces is presented. The size of the proposed tag is 25 mm${\times}$25 mm${\times}$3 mm. The impedance of the antenna can be easily matched to the tag chip impedance by adjusting the size of the shorting plate of the patch and the size of the feeding loop. The measured maximum reading distance of the tag at 910 MHz was 5 m when it was mounted on a 400 mm${\times}$400 mm metallic surface. The proposed design is verified by simulation and measurements which show good agreement.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.12 no.2
• /
• pp.21-29
• /
• 1992

Acceleration signal characteristics of a steel plate, impacted by steel balls, were studied in an attempt to apply the experimental results to the impact location and mass estimation of metallic loose parts in the cooling system of nuclear power plants. Experimental results show that the variation of maximum acceleration amplitude and impact contact time due to the change of ball mass and impact velocity can be well explained by the Hertz impact theory. The frequency spectral pattern shifted slightly in spite of the increase of impact velocity and impact location. Ball mass, however, strongly affected the frequency spectral pattern. Hence the frequency spectrum can be used for estimation of the mass of unknown loose parts in the cooling system.

• Solar Energy
• /
• v.6 no.1
• /
• pp.77-86
• /
• 1986

In this study, theoretical & Experiemental Analysis on three different air type solar collectors (One of metallic material: AI, two of non-metallic materials; GIWA & Slate) are performed. The results of three different collectors show the similiar performance in spite of different absorber material. The results of experiment are coincided with the theoretical results, and thus it is possible to estimate the performance of collector for the other experiment measuring variables. As a result, the thermal conductivity has no influence on the collector efficiency, because air, heat transfer medium, flows through over the whole surface of absorber plate.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2012.05a
• /
• pp.181-181
• /
• 2012

• Journal of electromagnetic engineering and science
• /
• v.12 no.1
• /
• pp.26-31
• /
• 2012

We have proposed a metamaterial lens that enables sub-wavelength focusing, which is shorter than an operating wavelength. Our lens is a two dimensional array of a unit cell consisting of a metallic dual-plate printed on a dielectric substrate. The unique dual-plate structure provides negativeness both in permittivity and permeability, with no help from conventional additional structures, which are normally printed on the opposite of metallic patterns. Therefore, we can focus a source (or an image) in a tiny distance shorter than the free space wavelength (${\lambda}$) at the frequencies of interest. Furthermore, since the proposed geometry does not need separate supplementary structures to acquire negative permittivity or permeability, our lens is much simpler than conventional metamaterial lenses, which is a strong point in practical applications. We have validated sub-wavelength focusing ability in a 6 GHz frequency band through an experiment of near field scanning, which provided the width of about 0.19 ${\lambda}$ at a half maximum of a peak value of an measured image. The width of the focused image through the lens is more than 4 times shorter than that without the lens, which confirms the validity of our design approach.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.32 no.1
• /
• pp.41-46
• /
• 2012

As the development of MEMS/NEMS structure and application technology the demand for an assessment of the mechanical properties have increased. The mechanical properties are mainly evaluated by using tensile test or ultrasonic wave measurement. However, the new technology have been developed such as nano-indentation, guided wave method because they have a limitation in case of a thin plate and thin film. In the study, the guided wave velocities are measured by electromagnetic-acoustic transducer(EMAT), the material properties of thin metallic foils are obtained using optimization process of the theoretical and experimental group velocity of guided wave. The Young's modulus obtained by the optimization process(201.6 GPa), nano-indentation(207.0 GPa) and literature value(203.7 GPa) of a $50{\mu}m$ thick nickel thin plate shows good agreement within 3%.

• Korean Journal of Metals and Materials
• /
• v.46 no.4
• /
• pp.257-266
• /
• 2008

AHydrogen induced cracking (HIC) was phenomenologically studied in terms of the effect of nonmetallic inclusions and hot rolling process parameters. By comparing the level of non-metallic inclusions in two different kinds of commercial grade steels having different HIC resistance, the role of non-metallic inclusions in HIC occurrence was investigated. Change in inclusion morphology and distribution during hot rolling was also studied throughout slab, rolling at austenite recrystallization region (roughing mill; RM) and rolling at austenite non-recrystallization region (finish mill; FM). In addition, the contribution of RM and FM parameters to HIC was investigated from the standpoint of change in inclusion morphology during hot rolling processes. As a result, HIC was closely related to the separation of large complex inclusion during hot rolling process. Large complex inclusions originated from the improper Ca treatment, after which equilibrium composition of slag should have resulted in eutectoid composition. By controlling the equilibrium slag composition equivalent to eutectoid one, HIC resistance could be improved due to the reduced size of inclusions. In addition, change in reduction/pass in RM had an effect on HIC resistance of steels while that in FM did not. Increase in the reduction/pass in the latter stage of RM improved HIC resistance of steels by enhancing the void enclosure around inclusions.

• Journal of the Korean institute of surface engineering
• /
• v.42 no.1
• /
• pp.53-57
• /
• 2009

Recovery of heavy-metallic component from a waste solution of factory was undertaken by the solar cell electricity. The solution was obtained from an electrolytic etching process of 316L stainless steel. The electrolysis of the solution for recovery of heavy metallic components was made with platinum plated titanium mesh anode and copper plate cathode. Analysis for the solution and electro-winned materials were made by EDS, XRD and SEM. Iron, chromium, and sulfur components were recovered on the cathode from the solution. Result of EDS analysis for the electro-winned materials revealed that some metal oxide were contained in the recovered material. The recovered materials were expected to have metallic form only by the electrolysis, but metal compounds were contained because of weak solar cell power. Nickel and manganese component in the solution doesn't recovered by this electrolysis process, but they made a sludge with phosphoric acid in the solution.

• Transactions of Materials Processing
• /
• v.21 no.1
• /
• pp.5-12
• /
• 2012

The weight of the bipolar plate is one of the crucial aspects of improving power density in PEMFC stacks. Aluminum alloys have good mechanical properties such as density, electrical resistivity, and thermal conductivity. Furthermore, using aluminum in a bipolar plate instead of graphite reduces the bipolar plate cost and makes machining easier. Therefore in this study, an aluminum alloy was selected as the appropriate material for a bipolar plate. Results from feasibility experiments with the aim of developing fuel cells consisting of Al bipolar plates with multiple channels are presented. Dynamic loading was applied and the formability of micro channels was estimated as a function of punch pressure and die radius. Sheets of Al5052 with a thickness of 0.3mm were used. For a die radius of 0.1mm the formability was optimized with a sine wave dynamic load of 90kN at maximum pressure and 5 cycles of a sine wave punch travel. The experimental results demonstrate the feasibility of the proposed manufacturing technique for producing bipolar plates.

• Korean Chemical Engineering Research
• /
• v.60 no.2
• /
• pp.295-299
• /
• 2022

In this paper, paint-free metallic plastic material, polypropylene (PP) and acrylonitrile styrene acrylate (ASA) materials were investigated on the applications for bumper skid plate and outside mirror housing parts. In order to maximize metallic effect, type, size and content of aluminum pigment were optimized based on flop index. Hybrid aluminum pigments with different aspect ratios were used to conceal weld lines. By controlling the fluidity of the material, the flow mark problem, generated on the surface of the part, was resolved. We also investigated the surface defects of flow and weld lines by using the developed modeling and simulation.