• ETRI Journal
• /
• 제30권4호
• /
• pp.600-602
• /
• 2008

A very small patch-type RFID tag antenna (UHF band) using ceramic material mountable on metallic surfaces is presented. The size of the proposed tag is 25 mm${\times}$25 mm${\times}$3 mm. The impedance of the antenna can be easily matched to the tag chip impedance by adjusting the size of the shorting plate of the patch and the size of the feeding loop. The measured maximum reading distance of the tag at 910 MHz was 5 m when it was mounted on a 400 mm${\times}$400 mm metallic surface. The proposed design is verified by simulation and measurements which show good agreement.

• 비파괴검사학회지
• /
• 제12권2호
• /
• pp.21-29
• /
• 1992

Acceleration signal characteristics of a steel plate, impacted by steel balls, were studied in an attempt to apply the experimental results to the impact location and mass estimation of metallic loose parts in the cooling system of nuclear power plants. Experimental results show that the variation of maximum acceleration amplitude and impact contact time due to the change of ball mass and impact velocity can be well explained by the Hertz impact theory. The frequency spectral pattern shifted slightly in spite of the increase of impact velocity and impact location. Ball mass, however, strongly affected the frequency spectral pattern. Hence the frequency spectrum can be used for estimation of the mass of unknown loose parts in the cooling system.

• 태양에너지
• /
• 제6권1호
• /
• pp.77-86
• /
• 1986

In this study, theoretical & Experiemental Analysis on three different air type solar collectors (One of metallic material: AI, two of non-metallic materials; GIWA & Slate) are performed. The results of three different collectors show the similiar performance in spite of different absorber material. The results of experiment are coincided with the theoretical results, and thus it is possible to estimate the performance of collector for the other experiment measuring variables. As a result, the thermal conductivity has no influence on the collector efficiency, because air, heat transfer medium, flows through over the whole surface of absorber plate.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2012년도 춘계학술발표회 논문집
• /
• pp.181-181
• /
• 2012

• Journal of electromagnetic engineering and science
• /
• 제12권1호
• /
• pp.26-31
• /
• 2012

We have proposed a metamaterial lens that enables sub-wavelength focusing, which is shorter than an operating wavelength. Our lens is a two dimensional array of a unit cell consisting of a metallic dual-plate printed on a dielectric substrate. The unique dual-plate structure provides negativeness both in permittivity and permeability, with no help from conventional additional structures, which are normally printed on the opposite of metallic patterns. Therefore, we can focus a source (or an image) in a tiny distance shorter than the free space wavelength (${\lambda}$) at the frequencies of interest. Furthermore, since the proposed geometry does not need separate supplementary structures to acquire negative permittivity or permeability, our lens is much simpler than conventional metamaterial lenses, which is a strong point in practical applications. We have validated sub-wavelength focusing ability in a 6 GHz frequency band through an experiment of near field scanning, which provided the width of about 0.19 ${\lambda}$ at a half maximum of a peak value of an measured image. The width of the focused image through the lens is more than 4 times shorter than that without the lens, which confirms the validity of our design approach.

• 비파괴검사학회지
• /
• 제32권1호
• /
• pp.41-46
• /
• 2012

MEMS/NEMS 구조체의 개발과 응용기술의 발달로 박판 및 박막의 기계적 물성 평가에 대한 요구가 점차 늘어나고 있다. 기계적 물성은 주로 인장시험이나 초음파의 속도 측정으로 평가되어 왔으나, 박판/박막 구조의 경우 기존의 기술로는 측정에 한계가 있어 나노압입시험법, 유도초음파법 등의 새로운 기술이 개발되고 있다. 본 연구에서는 박판 구조의 금속재료의 탄성계수를 평가하기 위하여 EMAT으로 송수신된 박판내에서의 유도초음파 진행 속도를 측정하였으며, 이론적으로 계산된 유도초음파 군속도와 실험적인 군속도의 최적화 과정을 통해 최종적으로 박판의 탄성계수를 평가하였다. 두께 $50{\mu}m$의 니켈 박판에서 측정된 영률은 201.6 GPa이었으며, 나노압입시험법으로 측정된 207 GPa, 참고문헌의 203.7 GPa과 비교하면 약 3% 내에서 일치하는 결과이다.

• 대한금속재료학회지
• /
• 제46권4호
• /
• pp.257-266
• /
• 2008

AHydrogen induced cracking (HIC) was phenomenologically studied in terms of the effect of nonmetallic inclusions and hot rolling process parameters. By comparing the level of non-metallic inclusions in two different kinds of commercial grade steels having different HIC resistance, the role of non-metallic inclusions in HIC occurrence was investigated. Change in inclusion morphology and distribution during hot rolling was also studied throughout slab, rolling at austenite recrystallization region (roughing mill; RM) and rolling at austenite non-recrystallization region (finish mill; FM). In addition, the contribution of RM and FM parameters to HIC was investigated from the standpoint of change in inclusion morphology during hot rolling processes. As a result, HIC was closely related to the separation of large complex inclusion during hot rolling process. Large complex inclusions originated from the improper Ca treatment, after which equilibrium composition of slag should have resulted in eutectoid composition. By controlling the equilibrium slag composition equivalent to eutectoid one, HIC resistance could be improved due to the reduced size of inclusions. In addition, change in reduction/pass in RM had an effect on HIC resistance of steels while that in FM did not. Increase in the reduction/pass in the latter stage of RM improved HIC resistance of steels by enhancing the void enclosure around inclusions.

• 한국표면공학회지
• /
• 제42권1호
• /
• pp.53-57
• /
• 2009

Recovery of heavy-metallic component from a waste solution of factory was undertaken by the solar cell electricity. The solution was obtained from an electrolytic etching process of 316L stainless steel. The electrolysis of the solution for recovery of heavy metallic components was made with platinum plated titanium mesh anode and copper plate cathode. Analysis for the solution and electro-winned materials were made by EDS, XRD and SEM. Iron, chromium, and sulfur components were recovered on the cathode from the solution. Result of EDS analysis for the electro-winned materials revealed that some metal oxide were contained in the recovered material. The recovered materials were expected to have metallic form only by the electrolysis, but metal compounds were contained because of weak solar cell power. Nickel and manganese component in the solution doesn't recovered by this electrolysis process, but they made a sludge with phosphoric acid in the solution.

• 소성∙가공
• /
• 제21권1호
• /
• pp.5-12
• /
• 2012

The weight of the bipolar plate is one of the crucial aspects of improving power density in PEMFC stacks. Aluminum alloys have good mechanical properties such as density, electrical resistivity, and thermal conductivity. Furthermore, using aluminum in a bipolar plate instead of graphite reduces the bipolar plate cost and makes machining easier. Therefore in this study, an aluminum alloy was selected as the appropriate material for a bipolar plate. Results from feasibility experiments with the aim of developing fuel cells consisting of Al bipolar plates with multiple channels are presented. Dynamic loading was applied and the formability of micro channels was estimated as a function of punch pressure and die radius. Sheets of Al5052 with a thickness of 0.3mm were used. For a die radius of 0.1mm the formability was optimized with a sine wave dynamic load of 90kN at maximum pressure and 5 cycles of a sine wave punch travel. The experimental results demonstrate the feasibility of the proposed manufacturing technique for producing bipolar plates.

• Korean Chemical Engineering Research
• /
• 제60권2호
• /
• pp.295-299
• /
• 2022

본 논문에서는 범퍼 스키드 플레이트 및 아웃사이드미러 하우징 부품에 적용되는 polypropylene (PP)와 acrylonitrile styrene acrylate (ASA) 소재를 활용하여 무도장 메탈릭 소재 구현에 대해 연구하였다. 금속 효과를 극대화하기 위해 알루미늄 입자의 종류, 크기, 함량을 최적화하였고 웰드 라인을 은폐하기 위해 종횡비가 상이한 하이브리드 알루미늄 입자를 사용하였다. 또한 부품 표면에 발생되는 플로우 마크를 개선하기 위해 유동성을 제어하였으며 사출 해석을 수행하였다.