• 센서학회지
• /
• 제27권6호
• /
• pp.357-361
• /
• 2018

This paper presents an averaging current adjustment technique for reducing the pixel resistance variation in a bolometer-type uncooled infrared image sensor. Each unit pixel was composed of an active pixel, a reference pixel for the averaging current adjustment technique, and a calibration circuit. The reference pixel was integrated with a polysilicon resistor using a standard complementary metal-oxide-semiconductor (CMOS) process, and the active pixel was applied from outside of the chip. The averaging current adjustment technique was designed by using the reference pixel. The entire circuit was implemented on a chip that was composed of a reference pixel array for the averaging current adjustment technique, a calibration circuit, and readout circuits. The proposed reference pixel array for the averaging current adjustment technique, calibration circuit, and readout circuit were designed and fabricated by a $0.35-{\mu}m$ standard CMOS process.

• Journal of Power Electronics
• /
• 제19권1호
• /
• pp.220-233
• /
• 2019

This work aims to study and analyze the various operating modes of universal power converter which is powered by solar and thermoelectric generators. The proposed converter is operated in a DC-DC (buck or boost mode) and DC-AC (single phase) inverter with high efficiency. DC power sources, such as solar photovoltaic (SPV) panels, thermoelectric generators (TEGs), and Li-ion battery, are selected as input to the proposed converter according to the nominal output voltage available/generated by these sources. The mode of selection and output power regulation are achieved via control of the metal-oxide semiconductor field-effect transistor (MOSFET) switches in the converter through the modified stepped perturb and observe (MSPO) algorithm. The MSPO duty cycle control algorithm effectively converts the unregulated DC power from the SPV/TEG into regulated DC for storing energy in a Li-ion battery or directly driving a DC load. In this work, the proposed power sources and converter are mathematically modelled using the Scilab-Xcos Simulink tool. The hardware prototype is designed for 200 W rating with a dsPIC30F4011 digital controller. The various output parameters, such as voltage ripple, current ripple, switching losses, and converter efficiency, are analyzed, and the proposed converter with a control circuit operates the converter closely at 97% efficiency.

• International journal of advanced smart convergence
• /
• 제10권1호
• /
• pp.12-23
• /
• 2021

This paper proposes a low power radio frequency receiver front-end where, in a single stage, single-balanced mixer and voltage-controlled oscillator are stacked on top of low noise amplifier and re-use the dc current to reduce the power consumption. In the proposed topology, the voltage-controlled oscillator itself plays the dual role of oscillator and mixer by exploiting a series inductor-capacitor network. Using a 65 nm complementary metal oxide semiconductor technology, the proposed radio frequency front-end is designed and simulated. Oscillating at around 2.4 GHz frequency band, the voltage-controlled oscillator of the proposed radio frequency front-end achieves the phase noise of -72 dBc/Hz, -93 dBc/Hz, and -113 dBc/Hz at 10KHz, 100KHz, and 1 MHz offset frequency, respectively. The simulated voltage conversion gain is about 25 dB. The double-side band noise figure is -14.2 dB, -8.8 dB, and -7.3 dB at 100 KHz, 1 MHz and 10 MHz offset. The radio frequency front-end consumes only 96 ㎼ dc power from a 1-V supply.

• ETRI Journal
• /
• 제44권5호
• /
• pp.859-874
• /
• 2022

This paper presents a low-power and lightweight human body communication (HBC) receiver with an embedded dummy electrode for improved signal acquisition. The clock data recovery (CDR) circuit in the receiver operates with a low supply voltage and utilizes a clock phase inversion scheme. The receiver is equipped with a main electrode and dummy electrode that strengthen the capacitive-coupled signal at the receiver frontend. The receiver CDR circuit exploits a clock inversion scheme to allow 0.9-V operation while achieving a shorter lock time than at 3.3-V operation. In experiments, a receiver chip fabricated using 130-nm complementary metal-oxide-semiconductor technology was demonstrated to successfully receive the transmitted signal when the transmitter and receiver are placed separately on each hand of the user while consuming only 4.98 mW at a 0.9-V supply voltage.

• 한국정보통신학회:학술대회논문집
• /
• 한국정보통신학회 2022년도 추계학술대회
• /
• pp.115-117
• /
• 2022

피드백 전계 효과 트랜지스터(feedback field-effect transistor; FBFET)로 구성된 모놀리식 3차원 정적 랜덤 액세스 메모리(monolithic 3-dimensional static random access memory; M3D-SRAM)에 대해 TCAD(technology computer-aided design) 프로그램을 사용하여 전기적 특성을 조사하였다. FBFET로 구성된 M3D-SRAM(M3D-SRAM-FBFET)는 FDSOI(fully depleted silicon on insulator) 구조의 N형 FBFET와 N형 MOSFET(metal oxide semiconductor field effect transistor)로 이루어져 있으며 각각 하부와 상부에 위치한다. M3D-SRAM-FBFET의 메모리 동작 시, 공급 전압이 1.9 V에서 감소함에 따라 읽기 전류가 낮아졌으며, 공급 전압이 1.6 V 일 때 읽기 전류가 약 10배 감소하였다.

• 한국재료학회지
• /
• 제33권5호
• /
• pp.195-204
• /
• 2023

Micro-electronic gas sensor devices were developed for the detection of carbon monoxide (CO), nitrogen oxides (NO_x), ammonia (NH₃), and formaldehyde (HCHO), as well as binary mixed-gas systems. Four gas sensing materials for different target gases, Pd-SnO₂ for CO, In₂O₃ for NO_x, Ru-WO₃ for NH₃, and SnO₂-ZnO for HCHO, were synthesized using a sol-gel method, and sensor devices were then fabricated using a micro sensor platform. The gas sensing behavior and sensor response to the gas mixture were examined for six mixed gas systems using the experimental data in MEMS gas sensor arrays in sole gases and their mixtures. The gas sensing behavior with the mixed gas system suggests that specific adsorption and selective activation of the adsorption sites might occur in gas mixtures, and allow selectivity for the adsorption of a particular gas. The careful pattern recognition of sensing data obtained by the sensor array made it possible to distinguish a gas species from a gas mixture and to measure its concentration.

• 한국재료학회지
• /
• 제33권6호
• /
• pp.229-235
• /
• 2023

An all-perovskite oxide heterostructure composed of SrSnO₃/Nb-doped SrTiO₃ was fabricated using the pulsed laser deposition method. In-plane and out-of-plane structural characterization of the fabricated films were analyzed by x-ray diffraction with θ-2θ scans and φ scans. X-ray photoelectron spectroscopy measurement was performed to check the film's composition. The electrical transport characteristic of the heterostructure was determined by applying a pulsed dc bias across the interface. Unusual transport properties of the interface between the SrSnO₃ and Nb-doped SrTiO₃ were investigated at temperatures from 100 to 300 K. A diodelike rectifying behavior was observed in the temperature-dependent current-voltage (IV) measurements. The forward current showed the typical IV characteristics of p-n junctions or Schottky diodes, and were perfectly fitted using the thermionic emission model. Two regions with different transport mechanism were detected, and the boundary curve was expressed by ln I = -1.28V - 13. Under reverse bias, however, the temperature- dependent IV curves revealed an unusual increase in the reverse-bias current with decreasing temperature, indicating tunneling effects at the interface. The Poole-Frenkel emission was used to explain this electrical transport mechanism under the reverse voltages.

• Current Optics and Photonics
• /
• 제7권5호
• /
• pp.485-495
• /
• 2023

The pixel size in high-resolution complementary metal-oxide-semiconductor (CMOS) image sensors continues to shrink due to chip size limitations. However, the pixel pitch's miniaturization causes deterioration of optical performance. As one solution, a quad color filter (CF) array with pixel binning has been developed to enhance sensitivity. For high sensitivity, the microlens structure also needs to be optimized as the CF arrays change. In this paper, the covered microlens, which consist of four microlenses covered by one large microlens, are proposed for the quad CF array in the backside illumination pixel structure. To evaluate the optical performance, the suggested microlens structure was simulated from 0.5 ㎛ to 1.0 ㎛ pixels at the center and edge of the sensors. Moreover, all pixel structures were compared with and without in-pixel deep trench isolation (DTI), which works to distribute incident light uniformly into each photodiode. The suggested structure was evaluated with an optical simulation using the finite-difference time-domain method for numerical analysis of the optical characteristics. Compared to the conventional microlens, the suggested microlens show 29.1% and 33.9% maximum enhancement of sensitivity at the center and edge of the sensor, respectively. Therefore, the covered microlens demonstrated the highly sensitive image sensor with a quad CF array.

• ETRI Journal
• /
• 제46권3호
• /
• pp.550-563
• /
• 2024

A novel inductance simulation circuit employing only two dual-output voltage-differencing buffered amplifiers (DO-VDBAs) and a single capacitance (grounded) is proposed in this paper. The reported configuration is a purely resistor-less realization that provides electronically controllable realized inductance through biasing quantities of DO-VDBAs and does not rely on any constraints related to matched values of parameters. This structure exhibits excellent behavior under the influence of tracking errors in DO-VDBAs and does not exhibit instability at high frequencies. The simple and compact metal-oxide semiconductor (MOS) implementation of the DO-VDBAs (eight MOS per DO-VDBA) and adoption of grounded capacitance make the proposed circuit suitable for on-chip realization from the perspective of chip area consumption. The function of the pure grounded inductance is validated through high pass/bandpass filtering applications. To test the proposed design, simulations were performed in the PSPICE environment. Experimental validation was also conducted using the integrated circuit CA3080 and operational amplifier LF-356.

• 한국재료학회지
• /
• 제34권5호
• /
• pp.235-241
• /
• 2024

Gas identification techniques using pattern recognition methods were developed from four micro-electronic gas sensors for noxious gas mixture analysis. The target gases for the air quality monitoring inside vehicles were two exhaust gases, carbon monoxide (CO) and nitrogen oxides (NO_x), and two odor gases, ammonia (NH₃) and formaldehyde (HCHO). Four MEMS gas sensors with sensing materials of Pd-SnO₂ for CO, In₂O₃ for NO_X, Ru-WO₃ for NH₃, and hybridized SnO₂-ZnO material for HCHO were fabricated. In six binary mixed gas systems with oxidizing and reducing gases, the gas sensing behaviors and the sensor responses of these methods were examined for the discrimination of gas species. The gas sensitivity data was extracted and their patterns were determined using principal component analysis (PCA) techniques. The PCA plot results showed good separation among the mixed gas systems, suggesting that the gas mixture tests for noxious gases and their mixtures could be well classified and discriminated changes.