• Journal of Welding and Joining
• /
• 제33권4호
• /
• pp.37-43
• /
• 2015

Characteristics of dissimilar metal welds between STS 316L and carbon steel ASTM A516 Gr.70 made with GTAW have been evaluated in terms of microstructure, ferrite content, chemical analysis, hardness and corrosion resistance. Three heat inputs of 9.00, 11.25, 13.00kJ/cm were employed to make joints of dissimilar metals with ER309 wire. Based on microstructural examination, the amount of vermicular type of ${\delta}$-ferrite was increased with increasing heat input due to the increase of Creq/Nieq in the second layer of welds. Based on the EDX analysis of weld metals, Cr and Ni content in the 2nd layer increased while those content in the first layer of welds decreased with heat inputs. Cellular solidification mode in the 1st layer and dendritic solidification mode in the 2nd layer due to different cooling rates were prevailed, respectively. Heat affected zone which formed hard microstructure showed higher hardness than the weld metal. The salt spray test of dissimilar metals weld joints showed that the carbon steel surfaces only corroded. The weight loss rate due to corrosion increased up to 100hours but it decreased above 100 hours. There was little difference in the weight loss caused by corrosion regardless of heat inputs.

• 한국재료학회지
• /
• 제12권8호
• /
• pp.600-607
• /
• 2002

The Ni-Zn synthetic ferrite were acquired from thermally decomposing the metal nitrates Fe(NO$_3$)$_3$.$9H_2$O, Zn($NO_3$)$_2$.$6H_2$O, Ni($NO_3$)$_2$. $6H_2$O, and Cu($NO_3$)$_2$. $3H_2$O at $150^{\circ}C$ for 24 hours and was calcined at $500^{\circ}C$. Each of those was pulverized for 3, 6, 9, and 12 hours in a steel ball mill and was sintered between $700^{\circ}C$ and $1,000^{\circ}C$ for 1 hour, and then their microstructures and electromagnetic properties were examined. We could make the initial specimens chemically bonded in liquid at the temperature as low as $150^{\circ}C$, by using the melting points less than $200^{\circ}C$ of the metal nitrates instead of the mechanical ball milling, then narrowed a distance between the particles into a molecular level, and thus lowed sintering temperature by at least $200^{\circ}C$ to$ 300^{\circ}C$. Their initial permeability was 50 to 400 and their saturation magnetic induction density and coercive force 2,400 G and 0.3 Oe to 0.5 Oe each, which were similar to those of Ni- Zn ferrite synthesized in the conventional process. In the graph of initial permeability vs frequencies, we could observe a $180^{\circ}C$rotation of the magnetic domain, which appears in a broad band of microwave near the resonance frequency.

• Journal of Welding and Joining
• /
• 제14권3호
• /
• pp.75-85
• /
• 1996

In this paper the influence of postweld heat treatment on mechanical properties of SMAW and FCAW stainless steel weldments was examined and the obtained results are as follows ; (1) The amount of $\delta$-ferrite formed by SMAW and FCAW process decreased with increasing holding temperature and time in post weld heat treatment(PWHT), and it was found that the reduced ferrite was transformed into sigma phase after $800^{circ}C{\times}50hr$ PWHT. This sigma phase, even though it was very small, resulted in brittleness of dissimilar weldment between carbon steel and stainless steel in bending test, however in similar weldment between stainless steel and stainless steel was not occured. (2) The chemical composition of sigma phase was measured to 28-30%Cr, 7-9%Mo, 4-6Ni in 316L weldment, and also 35-37%Cr, 0.9-1.0Mo, 6-8%Ni in 309L weldment by EDS analysis.

• 한국레이저가공학회지
• /
• 제16권3호
• /
• pp.1-10
• /
• 2013

In this study, Al-Si coated boron steel(1.2 mm) were laser welded by $CO_2$ laser and hot-stamping was applied to the laser joints. Tensile properties and microstructures of the joints were investigated before and after hot-stamping. Tensile and yield strengths of the as welded specimen similar with base metal and fracture occurred base metal of boron steel. Although, in case of heat treated specimen, fracture occurred fusion zone that Al segregated zone near the bond line. These could be explained by the existence of ferrite, in the Al segregated zone near the bond line and base metal of boron steel. Before hot-stamping, hardness of base metal is lower than fusion zone and heat affected zone in spite of exist Al segregation zone($Fe_3$(Al,Si)). So fracture occurred base metal. Although, after hot-stamping, microstructure of base metal and welds zone transformed to martensite and bainite except in Al segregation zone near the bond line that $Fe_3$(Al,Si) transformed to a-ferrite. So fracture occurred Al segregation zone near the bond line.

• 한국주조공학회지
• /
• 제19권1호
• /
• pp.77-83
• /
• 1999

Strip casting process, a new casting technology which makes thin strip of $0.5{\sim}5\;mm$ thickness directly from molten metal, has been dramatically developed for past 10 years and faced commercialization in the case of STS304 strip. In this study, ductile cast iron strip which is 1.1 mm thick and 100 mm wide is manufactured by the twin roll strip caster. Graphite and matrix structure of the strip can be controlled through heat treatments and the mechanical properties are examined. The microstructure of the as-cast strip consists of cementite and pearlite. Especially the equiaxed crystal zone of pearlite exists in the center region of the thickness due to the characteristics of the strip casting process. Matrix structure can be transformed into fully ferrite or ferrite/pearlite mixed structures by the different graphitization heat treatments. The heat-treated strip with ferrite/pearlite matrix structure showed higher hardness and tensile strength than that with full ferrite matrix structure.

• 한국세라믹학회지
• /
• 제39권12호
• /
• pp.1119-1123
• /
• 2002

Nanostructured spinel NiZn ferrites were prepared by the sol-gel method from metal nitrate raw materials. Analyses by X-ray diffraction and scanning electron microscopy showed the average particle size of NiZn ferrite was under 50 nm. The single phase of NiZn ferrites was obtained by firing at 250${\circ}C$, resulting in nanoparticles exhibiting normal ferrimagnetic behavior. The nanostructured $Ni_{1-X}Zn_XFe_2O_4$ (x=0.0∼1.0) were found to have the cubic spinel structure of which the lattice constants ${\alpha}_2$ increases linearly from 8.339 to 8.427 ${\AA}$ with increasing Zn content x, following Vegard's law, approximately. The saturation magnetization $M_s$ was 48 emu/g for x=0.4 and decreased to 8.0 emu/g for higher Zn contents suggesting the typical ferrimagnetism in mixed spinel ferrites. Pure NiZn ferrite phase substituted by Cu was observed before using the additive but hematite phase was partially appeared at $Ni_{0.2}Zn_{0.2}Cu_{0.6}Fe_2O_4$. On the other hand, the hematite phase in this NiZn Cu ferrite was disappeared after using the additive of acethyl aceton with small amount. The saturation magnetization Ms of $Ni_{0.2}Zn_{0.8-y}Cu_yFe_2O_4$(y=0.2∼0.6) as measured was about 51 emu/g at 77K and 19 emu/g at room temperature, respectively.

• Journal of Welding and Joining
• /
• 제34권3호
• /
• pp.69-76
• /
• 2016

Characteristics of dissimilar metal welds between ASTM Type 316L and carbon steel ASTM A516 Gr.70 made with FCAW were evaluated in terms of microstructure, ferrite content, EDS analysis, hardness, tensile strength, impact toughness and corrosion resistance. Three heat inputs of 10.4, 16.9, 23.4kJ/cm were employed to make joints of dissimilar metals with E309LMoT1-1 wire. Microstructure of dissimilar weld metals consisted of mostly vermicular type of ${\delta}$-ferrite and some lathy type of ${\delta}$-ferrite, and ${\delta}$-ferrite was transformed into globular type in reheated zone. In all conditions, weld metals were solidified on FA solidification mode. Based on the EDS analysis of weld metals, All Creq/Nieq values were in the range of FA solidification mode, and it was decreased with increasing heat inputs whereas it was increased with increasing layers. The amount of ${\delta}$-ferrite was decreased with increasing heat input due to the difference of cooling rate, and it was increased with increasing layers. Accordingly, hardness and tensile strength of dissimilar metals weld joints was decreased with increasing heat input while impact energy was increased with increasing heat input. Corrosion test of dissimilar metals weld joints showed that weight gain rate of heat input 10.4kJ/cm was the greatest, and that of three heat inputs became constant after certain time.

• 전자공학회논문지
• /
• 제54권7호
• /
• pp.49-54
• /
• 2017

본 연구에서 페라이트를 이용한 자기장 무선전력전송 안테나를 제안하였다. 기존에 추가접지가 있어야 자기장 무선전력전송이 가능하였던 점을 페라이트의 특성을 이용하여 추가접지 없이 자기장 무선전력전송이 가능하게 하였다. 페라이트는 자기장의 차폐효과가 있고 누설전력을 줄여주어 전송효율을 높여준다. 페라이트를 이용하여 자기장 무선전력전송을 위한 안테나를 제안하였고 실험을 통해 5W 자기장 무선전력전송 되는 것을 확인하였다. 본 논문에서 제안한 무선전력전송은 금속을 매개로하는 자기장 무선전력전송으로 사물인터넷 분야에 다양하게 응용 될 수 있다.

• 자원리싸이클링
• /
• 제12권6호
• /
• pp.13-18
• /
• 2003

Fe($NO_3$)$_3$ㆍ$9H_2$O, Zn($NO_3$)$_2$ㆍ$6H_2$O, Ni($NO_3$3)$_2$ㆍ $6H_2$O, Cu($NO_3$)$_2$ㆍ $3H_2$O와 같은 질산 금속염들을 $150^{\circ}C$로 24시간 동안 열분해하여 최초 NiCuZn ferrite 분체를 얻었으며, 이 분체 시료를 $500^{\circ}C$로 가소한 후 각각 볼밀 분쇄를 행하고 $700∼1000^{\circ}C$까지 각각 1시간씩 소결을 행하여 이에 대한 자기적 특성을 조사하였다. 일반 세라믹스 공정 보다 질산금속염들의 $ 200^{\circ}C$이하의 저 융점인 것을 이용하여 이들 출발 시료를 $150^{\circ}C$의 저온에서 액상의 화학결합이 가능하게 입자간의 거리를 분자적 거리로 좁힐 수 있었으며, 이로 인해 소결반응 점을 최소한 200∼ $300^{\circ}C$ 이상 낮출 수 있었다. 또한 이들의 초투자율은 50∼490, 포화자속밀도 및 보자력은 각각 2,400G와 0.3∼1.2 Oe정도로 보통의 ferrite 소결체의 특성과 유사하게 나타났다.

• 한국자기학회지
• /
• 제5권3호
• /
• pp.216-221
• /
• 1995

자성분말의 보자력$(H_{c})$과 보자력 분포도는 조성 이외의 제조공정인자에 크게 의존하는 값으로 자성분말 제조시 재현성을 결정하는 중요한 물성중의 하나이다. 자성분 말의 자기적 물성을 측정하는 VSM을 이용하여 쉽고 간단하게 보자력 분포도를 측정하는 방법과 그 응용예를 제시하였다. 보자력 분포도 측정은 magnetic hysteresis loop 의 dM/dH 대 H 곡선의 형태와 반치폭에서 얻을 수 있다. dM/dH 곡선 형태가 분리되는 것 없이 반치폭이 작아질수록 보자력 분포도는 더 균일해짐을 나타낸다. 보자력이 다 른 Ba-Ferrite와 ${\gamma}-Fe_{2}O_{3}$ 혼합물 중 Ba-Ferrite의 $H_{c}$가 높아질수록 dM/dH 대 H 곡선 형태는 peak broadening 후 peak splitting으로 나타나며, 이 peak splitting은 혼합자성분말의 $H_{c}$ 차이가 600 Oe 이상일 때 일어난다. 또한 dM/dH 대 H 곡선의 응용으로는 자성분말 보자력 분포도 측정, Ba-Ferrite 구조내로 dopants의 치환 능력 및 ${\alpha}-Fe$의 산화거동을 연구하는데 사용될 수 있다.