• Korean Journal of Environmental Agriculture
• /
• v.15 no.3
• /
• pp.275-281
• /
• 1996

When soybean was cultivated in the polluted soil with heavy metals, the content of these heavy metals affected. The results were summarized as follows. 1. The growth of soybean was remarkably poor and the content of heavy metals in polluted soil were higher than in unpolluted soil. 2. In leaves of all surveyed crops, the content of Zn, Cu, Pb, Cd and As was higher in soybean, followed by corn and rice. 3. Except for Pb, the content of heavy metals in the leaves of soybean was higher than in the stem of soybean, and the components of heavy metals in each part of soybean were shown in order of Zn > As > Cd > Cu > Pb. 4. The relationship between the content of Zn, Cu, Pb, Cd, As and the growth of soybean was negatively correlated, respectively. 5. A higher correlation seemed to exist among the content of Zn, Cu, Pb, Cd, As in soil, of Zn, Cu and As in soybean leaves, and of Pb, Cd and As in stems of soybean. The results indicated that heavy metals were absorbed and accumulated by plants grown in the polluted area.

• Analytical Science and Technology
• /
• v.8 no.1
• /
• pp.1-7
• /
• 1995

Spectrophotometric determination of U(VI) and Th(IV) by Flow injection method is described. Chrome Azurol S forms water soluble complexes with U(VI) and Th(IV) in the presence of cethyltrimethylammonium bromide. The maximum adsorption of U(VI) and Th(IV) complexes are at 600nm with molar absorptivity of $2.3{\times}10^5Lmol^{-1}cm^{-1}$ and 611nm with molar absorptivity of $3.8{\times}10^5Lmol^{-1}cm^{-1}$ in acetate buffer medium having pH 5.0 and 5.5. The calibration curves of U(VI) and Th(IV) are linear over the range of 0.1~0.8ppm and the correlation coefficients are ca. 0.9960 and 0.9930 respectively. The detection limits(S/N) are 20ppb for U(VI) and 15ppb for Th(IV). The relative standard deviation are ${\pm}1.8%$ for U(VI) and ${\pm}2.1%$ for Th(IV). The sample throughput was ca. $50hr^{-1}$.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.17 no.4
• /
• pp.36-47
• /
• 2009

Microbial and related biochemical mass of composts are important for optimization of its process and end-products. This study was carried out to assess the specific microbial and related biochemical mass which could be used as an indicator for compost maturity during composting stages. The samples from five compost plants were collected at three stages (Initial, Thermophilic and Mature) and analyzed for total aerobic bacteria (TAB), Coliforms, Escherichia coli, Actinomycetes and fungi. Significantly, the coliforms and E.coli counts decreased during the thermophilic stage and were completely eliminated during mature stage. However, the other microbial mass were completely eliminated during mature stage. Which disclosed that Coliforms and E.coli communities can be used as compost maturity indicator. Interestingly, the microbial biomass carbon and nitrogen ratio (MBC/MBN) were decreased a little during the thermophilic stage due to the decreasing number of coliforms, Ecoli and fungi, while the ratio increased during the mature stage due to increasing fungal and aerobic bacterial counts. In addition the heavy metals were shown strong negative correlation with Actenomycetes. This study provides insight to the evaluation of compost maturity as well as the quality by the metal-microbial interactions.

• Journal of the Korean Magnetics Society
• /
• v.17 no.1
• /
• pp.10-13
• /
• 2007

Single crystalline, $LuFe_2O_4$, was grown by the floating zone method. The crystal structure was a two-dimensional layered-type rhombohedral($R\={3}mh$) structure, with an $a_0=3.440(2)\;{\AA}\;and\;a\;c_0=25.263(2)\;{\AA}$. The magnetic $N\'{e}el$ temperature($T_N$) was determined to be 250 K. The $M\"{o}ssbauer$ spectrum at 12 K was fitted with four sextet sets which was resulted from the crystal structure. The spectrm at room temperature consisted of three singlets and a doublet with the electric quadrupole splitting. The isomer shift($\delta$) value of the singlet was $0.20{\pm}0.01mm/s$ relative to the Fe metal indicating the $Fe^{3+}$ valence state, and the value of the doublet was $0.70{\pm}0.01mm/s$ indicating $Fe^{2+}$. The $M\"{o}ssbauer$ absorption area ratio between $Fe^{3+}$ and $Fe^{2+}$ at room temperature was 1:1. The doublet phase of spectra gradually disappears by up to 360 K. At 360 K, the spectrum shows the singlet phase. We suggested that the spontaneous polarization effect of $LuFe_2O_4$ was caused by the change of iron behavior.

• Journal of the Korean Chemical Society
• /
• v.36 no.1
• /
• pp.3-15
• /
• 1992

Electronic structures and reactivities of the chromium, molybdenum, and tungsten carbene complexes, $(CO)_5Cr=CCHCH_2(XCH_3)\;,\;(CO)_5Mo=CCHCH_2(XCH_3)\;, and\;(CO)_5W=CCHCH_2(XCH_3)$, are studied by means of Extended Huckel calculations. The origin of the M=Ccarbene double bond is clarified from the diagram of the orbital correlation with the fragment orbitals. The ${\sigma}$ bond of the M=Ccarbene double bond is formed by the electron transfer interaction from the HOMO of the carbene to the LUMO of the $(CO)_5M$. The ${\pi}$ bond is formed through the back-transfer of electrons from one of the degenerated d${\pi}$ orbitals to the LUMO of the carbene. The polarization of charge of the M=Ccarbene bond is calculated to be M=Ccarbene for Mo, and W carbenes. The chemical and physical properties of these complexes are resulted from an appreciable positive charge on the carbene carbon. The electrophilic reactivity of the carbene carbon is not charge controlled, but is controlled by the frontier orbital, LUMO.

• Journal of Life Science
• /
• v.26 no.9
• /
• pp.1074-1081
• /
• 2016

Mistletoes are hemi-parasitic plant growing on different host tree and shrubs. They are traditionally used in folkloric medicine for the treatment of diarrhea, cough, diabetes, hypertension, cancer and skin infection. The purpose of this study was to determine the contents of phenolics and antioxidant activity of 70% ethanol, 100% methanol and hot water extracts of Jeju camellia mistletoe (Korthalsella japonica Engl.). Ethanol was most effective in extracting total phenols (7,427 mg gallic acid equivalent (GAE)/100 g) and flavonoid (1,777 mg rutin equivalent (RE)/100 g). The free radical scavenging activity, 1,1-diphenyl-2-picryl hydrazyl (DPPH) (EC₅₀ = 7.8 mg/ml) and hydrogen peroxide (H₂O₂) (EC₅₀ = 1.4 mg/ml), and the capacity for chelating metal ions (EC₅₀ = 8.0 mg/ml) and reducing power (EC₅₀ = 14.9 mg/ml) of the samples also higher in ethanolic extracts. The strong correlation (r² = −0.996～−0.881) between antioxidant capacities and the phenolic contents implied that phenolic compounds are a major contributor to the antioxidant activity of the ethanolic extracts of Jeju camellia mistletoe. As conclusions, Jeju camellia mistletoe contains bioactive substances with a potential for reducing the physiological as well as oxidative stress and this could explain the suggested cancer preventive effect of these plants as well as their protective role on other major diseases.

• Journal of Korea Foundry Society
• /
• v.11 no.6
• /
• pp.475-481
• /
• 1991

In this study the fabrication technology and mechanical properties of AC8A/$Al_2O_3$ Composites by squeeze casting process were investigated to develope for application as the piston materials that require good friction, wear resistance, and thermal stability. AC8A/$Al_2O_3$ composistes without a porosity and the break of preform were fabricated at the melt temperature of $740^{\circ}C$, the preform temperature of $500^{\circ}C$, and mold temperature of $400^{\circ}C$ under the applied pressure of $1200kg/cm^2$ as the results of the observation of microstructures. As the results of this study, the tensile strength of AC8A/$Al_2O_3$ composites was not increased linearly with $Al_2O_3$ volume fraction and so it seemed not to agree with the rule of mixture, which had been used often in metal matrix composite. Also the tensile strength after thermal fatigue test was little different from that before the test. Consequently it was thought that AC8A/$Al_2O_3$ composites fabricated under our experimental conditions had a good thermal stability and subsequently a good interface bonding. Wear rate(i.e., volume loss per unit sliding distance) of AC8A/$Al_2O_3$ composites was decreased with $Al_2O_3$ volume fraction and the sliding speed at both room temperature and $250^{\circ}C$ and so there was a good correlation between wear rate and hardness. Also the wear rate of AC/8A20% $Al_2O_3$ composities was obtained the value of $1.65cm^3/cm$ at sliding speed of 1.14m/sec as compared with about $3.0\;{\times}10^{-8}cm^3/cm$ hyereutectie Al-Si alloy(Al-16%Si-2%Cu-1%Fe-1%Ni), which applied presently for piston materials. The wear behavior of $Al_2O_3$ composites was observed to a type of abrasive wear by the SEM view of wear surface.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.40 no.4
• /
• pp.164-170
• /
• 2017

The CNC machine tool field is showing a growing trend with the recent rapid development of manufacturing industries such as semiconductors, automobiles, medical devices, various inspection and test equipment, mechanical metal processing equipment, aircraft, shipbuilding and electronic equipment. However, small and medium-sized machining companies that use CNC machine tools are experiencing difficulties in increasingly intense competition. Especially, small companies which are receiving orders from 3rd or 4th venders are very difficult in business management. In recent years, company S experienced difficulty to make product quality and delivery time due to the ignorance of the processing method when manufacturing cooling plate jig made of SUS304 material used for cell phone liquid crystal glass processing. In order to solve these problems, we redesigned the process according to the size of our company and tried to manage all processes with quantified data. In the meantime, we have found that there is a need to improve the cutter process, which accounts for most of the machining process. Therefore, we have investigated the correlation between RPM and FEED of three cutters that have been used in the past. As a result, we found that it is the most urgent problem to solve the roughing process during the cutter operation which occupies more than 70% of the total machining. In order to shorten the machining time and improve the quality in machining of SUS304 cooling plate jig, we select the main factors such as price, tool life, maintenance cost, productivity, quality, RPM, and FEED and use AHP to find the most suitable milling cutter. We also tried to solve the problem of delivery, quality and production capacity which was a big problem of S company through experiment operation with selected cutter tool. As a result, the following conclusions were drawn. First, the most efficient of the three cutters currently available in the machining center has proven to be an M-cutter. Second, although one additional facility was required, it was possible to produce the existing facilities without additional investment by supplementing the lack of production capacity due to productivity improvement. Third, the Company's difficulties in delivery and capacity shortfalls have been resolved. Fourth, annual sales increased by KRW 109 million and profits increased by KRW 32 million annually. Fifth, it can confirm the usefulness of AHP method in corporate decision making and it can be utilized in various facility investment and process improvement in the future.

• The Journal of Korean Academy of Prosthodontics
• /
• v.39 no.3
• /
• pp.260-272
• /
• 2001

All-ceramic restorations have had a more limited life expectancy than metal ceramic restorations because of their low strength. Their relatively lower strength and resistance to fracture have restricted the use of all-ceramic crowns to anterior applications where occlusal loads are lower. But there has been increasing interest in all-ceramic restorations because patients are primarily concerned with improved esthetics. Many efforts have been made to in prove the mechanical properties of dental ceramics. This study was designed to elucidate the influence of the luting agent on the strength of the Empress 2 crown (staining technique) cemented on human teeth. Seventy extracted human permanent molar teeth were chosen. Teeth were prepared for Empress 2 crowns with milling machine on a surveyor. A dental bur was placed in the mandrel that was positioned so that the long axis of the bur was perpendicular to the surveyor base. Dimensions of the Empress 2 crown preparation were $6^{\circ}$ taper on each side, $1.5{\pm}0.1mm$ shoulder margin, and 4mm crown height. The luting cements used in this study were as follow: 1. Uncemented 2. Zinc phosphate cements (Confi-Dental) 3. Conventional glass ionomer cement : Fuji 1 (GC) 4. Resin-modified glass ionomer cements : Fuji plus (GC) 5. Adhesive cements : Panavia F (Kuralay), Variolink II (Vivadent), Choice (Bisco). Fracture test using Instron. The crowns were loaded in compressive force to evaluate the effect of these cements on the breaking strength of these all-ceramic crowns. A steel ball with a diameter of 4mm was placed on the occlusal surface and load was applied to the steel ball by a cylindrical bolt with a crosshead speed of 0.5mm per minute until fracture occurred. The fractured surface was examined using Scanning Electron Microscopic Image (SEM) to discover the correlation between fracture strength and bonding capacity. Within the limitation of this in vitro study design, the results were as follows : 1. fomentations significantly increased the fracture resistance of Empress ceramic crowns compared to control. Uncemented (206.9 N): ZPC (812.9 N): Fuji 1 (879.5 N): Fuji Plus (937.7 N): Choice (1105.4 N): Variolink II (1221.1 N): Panavia F (1445.2 N). 2. Resin luting agent, treated by a silane bond enhancing agents, yielded a significant increase in fracture resistance. In some of the Panavia F group, a fracture extended into dentin. 3. According to SEM images of fractured Empress crowns, the stronger the bond at both interfaces(crown and die), the more fracture strength was acquired.

• Journal of the Korean Chemical Society
• /
• v.41 no.4
• /
• pp.180-185
• /
• 1997

Zinc, cadmium, lead and copper were simultaneously determined by depositing metals at - 1.200 V vs. a Ag/AgCl(sat. KCl) reference electrode for 150 seconds on a hanging mercury drop electrode(HMDE) or a thin mercury film electrode(TMFE), followed by scanning towards anodic direction using differential pulse voltammetric(DPASV) and square wave voltammetric(SWASV) techniques. The linear calibration curves were obtained for four metal ions simultaneously determined by DPASV with a HMDE in the concentration range between 20 and 100 ppb. However, the linear calibration plots were obtained only for $Cd^{2+}$ and $Pb^{2+}$ in the simultaneous determinations with a TMFE in the concentration range up to 100 ppb using DPASV and up to 10 ppb using SWASV. DPASV with a TMFE was about 15 times more sensitive than DPASV with a HMDE for simultaneous determinations of $Cd^{2+}$ and $Pb^{2+}$. SWASV was about 5 times more sensitive than DPASV at a TMFE. Concentrations of zinc in seven different sediment samples determined by DPASV with a HMDE and inductively coupled plasma-mass spectrometry were compared, resulting with an excellent correlation coefficient of 0.9993 and with no significant difference between two methods after t-test.