• Journal of the Korean Electrochemical Society
• /
• v.11 no.4
• /
• pp.262-267
• /
• 2008

Effective dispersion of noble metal Pt-Ru catalysts was conducted for the application of direct formic acid fuel cell(DFAFC) electrodes by electrospray method. The amount of catalysts deposited on the electrodes increased with increasing deposition time. However, the performance of cell test decreased with the deposition time after 80 min. because of agglomeration of catalysts. With the conventional hand-spray method, the density of the anode catalysts deposited was $3.0\;mg/cm^2$ and the maximum power density of the MEA was $74\;mW/cm^2$. On the other hand, the MEA prepared by the electrospray method, showed a similar power density of $72\;mW/cm^2$. However, the density of the anode catalysts deposited was much lower than the case of the hand-spray and the density the anode catalysts in this case was $1.85\;mg/cm^2$.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.24 no.2
• /
• pp.1-13
• /
• 2020

The characterization of aging of the pyrotechnic device is conducted thermally, chemically, and spectroscopically. The device is comprised of two parts: (i) igniter composed of Zr and (ii) pyrotechnic delay composed of ZrNi alloy. The thermally induced chemical reaction is identified through Differential Scanning Calorimetry (DSC) and Thermogravimetry Analysis (TGA). The peak deconvolution of the themo-chemical data is used to estimate the enthalpy change of each metallic fuel component. Laser Induced Breakdown Spectroscopy (LIBS) and X-ray Photoelectron Spectroscopy (XPS) are used for chemical species analysis. The decomposition of oxidants by moisture significantly affected the fuel aging, and the formation of oxide film and metal oxide on the fuel surface gave rise to the thermal energy decrease.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.9 no.1
• /
• pp.89-94
• /
• 2003

As ship's fuel oil recently becomes viscous and the amount of sludge increases, many researches and studies are underway to process the sludge onboard the ship and to recycle it as a fuel for ship's boiler. Of many researches, especially ultrasonic emulsifier to break the particle of sludge into fine pieces is recognized as a most possible recycling device. In this regards, the author investigates the property change of sludge's temperature and pressure at the early stage of the study of ultrasonic emulsifier. This study can be used as a useful dora to determine the proper temperature and pressure to inject the processed sludge in the boiler injector and the results can also be comparable dora with the experimental data by ultrasonic emulsifier. In addition, the results will be a fundamental data to study the filtering efficiency of the sludge particle broken by temperature and pressure. It is expected that this study ultimately play a role to prevent marine oil pollution as the sludge is recycled onboard the ship and used as a fuel for boiler.

• Korean Journal of Materials Research
• /
• v.12 no.4
• /
• pp.259-263
• /
• 2002

Three different ribbons of amorphous $Til_{1-x}Be_x$ alloys such as $Ti_{0.59}Be_{0.41},\;Ti_{0.61}Be_{0.39}\;and\;Ti_{0.63}Be_{0.37}$ were made by melt-spinning method to be used as brazing filler metals for joining Zircaloy-4 nuclear fuel cladding tubes, and their crystallization behavior as well as microstructure of the brazed zone were examined. The crystallization behavior was investigated in teams of thermal stability, crystallization temperature and activation energy. The crystallization of the $Ti_{1-x}Be_x$ alloys proceeded in two steps by the formation of ${\alpha}$-Ti at a lower temperature and of TiBe at a higher temperature. The crystallization temperature and activation energy of $Ti_{1-x}Be_x$ alloys were higher and larger than those of $Zr_{1-x}Be_x$ alloys and PVD Be. Those resulted thinner joining layer with $Ti_{1-x}Be_x$ alloys, which kept sound thickness of Zircaloy-4 nuclear fuel cladding tubes after brazing. But in the brazed zones made by $Ti_{1-x}Be_x$ filler metals, a little solid-solution layers composed of Zr and Ti were formed toward the Zr cladding tube and Zr was detected in the brazed zones. Microstructure of brazed zone was changed from globular to dentrite with decreasing Be content in the $Ti_{1-x}Be_x$ filler metal.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.44 no.7
• /
• pp.576-584
• /
• 2016

In this study, AP added propellant has been proposed as a method of enhancing the low specific impulse performance found for staged hybrid rocket engine. Experimental tests were carried out to analyze and evaluate the effect of AP added propellant on specific impulse performance as well as fuel-rich combustion characteristics in a staged hybrid rocket engine. Upper limit of AP content in propellant was set to be 15 wt% to maintain the hybrid rocket engine advantages. As a result, 15 wt% AP added propellant showed 3% higher specific impulse performance compared to 0 wt% AP added propellant. Moreover, AP addition proved to offer less injected oxidizer mass flow, less O/F variation, and less combustion pressure while producing fuel-rich gas of the same combustion temperature. Future studies will carry out more combustion tests with metal additives to further enhance specific impulse.

• Elastomers and Composites
• /
• v.42 no.4
• /
• pp.232-237
• /
• 2007

We examined the properties of compound and made compound of the optimum state using the properties of each material to evaluate suitability of FKM, VMQ, EPDM, NBR with gasket for fuel cell which is in general use with the material of gasket. It could be found from the compound made with setting the optimum state that NBR is worse than FKM in the chemical property of matter for a long term, and VMQ is worse than FKM in the elution of a metal ion, and EPDM is worse than FKM in the permeability of gas. As a result of leak evaluation of gasket for fuel cell with using FKM, it appeared leak in short time when contracting pressure is getting lower and sealing pressure is getting higher. And as a result of the life prediction with using Arrhenius model, we could predict that it is possible to continuously drive for 60,000 hours.

• Resources Recycling
• /
• v.20 no.4
• /
• pp.52-57
• /
• 2011

Present paper reports a new method to separate the electrolyte membranes and carbon paper without using ultrasonic waves and stirring. In this method, these were separated from fuel cell membrane-electrode assembly(MEA) using the distilled water, butanol and surfactant by dipping method without the dispersion of catalyst particles. Separated carbon paper catalysts and fuel cell Pt/C catalysts were heated in aqua regia at $80{\sim}85^{\circ}C$ and added to precipitant. After calcination, Pt metal was recovered which might be used in fabricating new fuel cells.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.18 no.5
• /
• pp.95-100
• /
• 2014

In hypersonic aircraft, increase of aerodynamic heat and engine heat leads heat loads in airframe. It could lead structural change of aircraft's component and malfunctioning. Endothermic fuels are liquid hydrocarbon fuels which are able to absorb the heat load by undergoing endothermic reactions. In this study, exo-tetrahydrodicyclopentadiene was selected as a model endothermic fuel and experiments on endothermic properties were investigated with pore structure controlled zeolite catalyst using metal deposition. We secured the catalyst that had better endothermic performance than commercial catalyst. The object of this study is inspect catalyst properties which have effect on heat absorption improvement. Synthetic catalyst could be applied to system that use exo-THDCP as endothermic fuel instead of other commercial catalyst.

• Korean Chemical Engineering Research
• /
• v.60 no.1
• /
• pp.70-79
• /
• 2022

Biodiesel production has attracted attention as a sustainable source of fuel and is a competitive alternate to diesel engines. The glycerol that is produced as a by-product is generally discarded as waste and can be converted to green chemicals such as acetins to increase bio-diesel profitability. Acetins find application in fuel, food, pharmaceutical and leather industries. Batch experiments and analysis have been previously conducted for synthesis of acetins using glycerol esterification reaction aided by sulfated metal oxide catalysts (SO₄^2-/CeO₂-ZrO₂). The aim of this study was to optimize process parameters: effects of mole ratio of reactants (glycerol and acetic acid), catalyst concentration and reaction temperature to maximize glycerol conversion/acetin selectivity. The optimum conditions for this reaction were determined using response surface methodology (RSM) designed as per a five-level-three-factor central composite design (CCD). Statistica software 10 was used to analyze the experimental data obtained. The optimized conditions obtained were molar ratio - 1:12, catalyst concentration - 6 wt.% and temperature -90 ℃. A packed bed reactor was fabricated and column studies were performed using the optimized conditions. The breakthrough curve was analyzed.

• Composites Research
• /
• v.34 no.6
• /
• pp.406-411
• /
• 2021

PEM (proton exchange membrane) fuel cells generate only water as a by-product, and thus are in the spotlight as an eco-friendly energy source. Among the various components composing the stack of the fuel cell, research on the bipolar plate that determines the efficiency of the fuel cell is being actively conducted. The composite bipolar plate has high strength, rigidity and corrosion resistance, but has the disadvantage of having a relatively low electrical conductivity. In this study, to overcome these shortcomings, a gas diffusion layer (GDL)-composite bipolar plate assembly was developed and its performance was experimentally verified. The graphite foil coating method developed in the previous study was applied to reduce the contact resistance between the bipolar plate and the GDL. In addition, in order to improve electron path in the stack and minimize the contact resistance between the GDL and the bipolar plate, a GDL-bipolar plate assembly was fabricated using a thin metal foil. As a result of the experiment, it was confirmed that the developed GDL-bipolar plate assembly had 98% lower electrical resistance compared to the conventional composite bipolar plate.