• Journal of Electrical Engineering and Technology
• /
• v.6 no.6
• /
• pp.817-823
• /
• 2011

This paper introduces an efficient voltage multiplier circuit for improved voltage gain and power efficiency of radio frequency identification (RFID) tags. The multiplier is fully integratable and takes advantage of both passive and active circuits to reduce the required input power while yielding the desired DC voltage. A six-stage voltage multiplier and an ultralow power voltage regulator are designed in a 0.13 ${\mu}m$ complementary metal-oxide semiconductor process for 2.45 GHz RFID applications. The minimum required input power for a 1.2 V supply voltage in the case of a 50 ${\Omega}$ antenna is -20.45 dBm. The efficiency is 15.95% for a 1 $M{\Omega}$ load. The regulator consumes 129 nW DC power and maintains the reference voltage in a 1.1% range with $V_{dd}$ varying from 0.8 to 2 V. The power supply noise rejection of the regulator is 42 dB near a 2.45 GHz frequency and performs better than -32 dB from 100 Hz to 10 GHz frequencies.

• Proceedings of the KIEE Conference
• /
• 2001.07c
• /
• pp.1724-1726
• /
• 2001

This paper deals with the characteristics of the potential rises of down-conductor due to lightning surge currents. Direct lightning strikes can cause high impulse currents to the lightning protection system(LPS) of a building. These high impulse currents have the front time as short as 1[${\mu}s$]. In this case, the induced voltages caused in a closed circuit inside the building can be very high and cause damage or submit people to electric hazard. So, the LPS has to be designed to ensure safety condition to person and acceptable levels of induced voltages to the electrical and electronic equipments. The results of the potential rises related to the bonding conditions between the grounding conductor and metal raceway and the type of down-conductors are introduced.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.11 no.6
• /
• pp.953-962
• /
• 1987

Domestic dissimilar structural steels, SM 45 C and SUS304 were friction welded under optimal welding condition and the micro-artificial holes were drilled at SM 45 C base metal, SM 45 C HAZ, welded zone, SUS 304 HAZ, and SUS 304 base metal for fatigue behavior tests. In this study, the fatigue limit and the behavior of micro-crack propagation, crack propagation rate, and its dependency on stress intensity factor under the low stress level and high stress level of bending stress have been investigated. The results obtained are as follows. (1) The fatgiue strength of the portion of SM45C B.M., SM45C HAZ, welded zune, SUS304 HAZ and SUS304 B.M. on notched friction welded specimens are 20 kgf/mm$^{2}$, 32 kgf/mm$^{2}$, 27kgf/mm$^{2}$, 29kgf/mm$^{2}$, and 29kgf/mm$^{2}$, respectively. (2) The fatigue strength of welded zone of unnotched and notched specimens are 32.5kgf/mm$^{2}$, and 27kgf/mm$^{2}$, respectively. (3) Micro-crack initiation in the welded zone, HAZ, and each base metals occurrs simultaneously in front and rear of micro-hole tips in the view of the rotational directions. (4) Fatigue crack propagates more slowly in the welded zone than in another protions of specimen, regardless of the magnitude of the stress level. (5) Fatigue crack propagation rates were plotted as a function of stress intensity range. The value of m in the equation da/dN=C(.DELTA.K)$^{m}$ was found to range from 2.09-2.55 in this study.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.33 no.2
• /
• pp.160-164
• /
• 2013

A laser ultrasonic inspection system is a non-contact inspection device which generates and measures ultrasonics by using laser beam. A laser ultrasonic inspection system provides a high measurement resolution because the ultrasonic signal generated by a pulse laser beam has a wide-band spectrum and the ultrasonic signal is measured from a small focused spot of a measuring laser beam. In this study, galvanic corrosion phenomenon was measured by non-destructive and non-contact method using the laser. The case of mixed foreign material on the part of corrosion was assumed and laser ultrasonic experiment was conducted. Ultrasonic was generated by pulse laser from the back side of the specimen and ultrasonic signal was acquired from the same location of the front side using continuous wave laser and Confocal Fabry-Perot Interferometer(CFPI). The characteristic of the ultrasonic signal of exist foreign material part was analyzed and the location and size of foreign material was measured.

• KOMUNHWA
• /
• no.70
• /
• pp.63-88
• /
• 2007

The purpose of this writing is to examine the places and instruments of the dissection for deformed animal carcasses excavated in shellfish stacks of the period of the Proto-Three Kingdoms(삼한) and the Three Kingdoms(삼국). The remains were chosen, which had been excavated and finished in the analysis of the animal carcasses, and the main objects are all shells and deer, especially among Mammalia. As the result, the dissection of shells was not taken place in the habitats of the animals, but inside or around of the residence of the people. For deer, too, it was done in the public place or specific area around and inside the residence. As concerns the method of dissection for shells, for Pelecypoda(부족류), represented by Meretrix lusoria(백합), the inner meat was taken out by wrenching the shell with a kind of small knives, or by boiling, and sometimes by cracking the middle of the shell in the case of big Meretrix lusoria and Dosinorbis japonicus(떡조개). For Rapana venosa(피뿔고둥), representative of Gastropoad(배발류), the people broke the top or some parts of the body to get the inner meat or used some kind of needles and stylus to pick the inner meat out after boiling. Abalones‘ meat was attached firmly to the shell, so very sharp and proper metal instruments were used to take the meat out Relatively small-sized Reishia clavigera(대수리),Top shell(밤고둥) meats were taken out by breaking the top parts after boiling, then sucking the meats, or by picking them out by using needles and stylus in the original shape. In the case of large Mammalia like deer, in the full consideration of the point that deer itself are used in various ways, they were dissected in the order of skinning, taking out the internal organs, cutting front and rear legs, separating joint parts and meats, extracting bone-marrow by 철정, 철부, ironed hand knife in very delicate ways. It seems that skinning, and front and rear legs' cutting were taken place in the place around the residence, on the other hand joint parts' separating and bone-marrow extracting in the residence. The tools for the dissection were confirmed to be hand-knife, honed ax, hammer stone, bondstone, needles and stylus, and some other sharp instrument. They were used properly according to objects.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.13 no.11
• /
• pp.4956-4962
• /
• 2012

Among the various parts of automobile, automotive seat is the most fundamental item that ride comfort can be evaluated as the direct contact part with human body. Automotive seat must have the sufficient rigidity and strength at the same time with ride comfort. In this study, cushion frame and back frame at car seat are modelled with 3D. There are structural simulation analyses about 3 kinds of tests on torsion strength, vertical load strength and back frame strength. In the analysis result, the initial total deformation and the permanent total deformation has the maximum values of 5.4821 mm and 0.02539mm respectively at the torsion strength test of cushion frame. Total deformations at front and rear end parts of cushion frame become the values of 2.1159mm and 0.0606mm respectively at the test of vertical load strength of cushion frame. In case of more than this load, the maximum value of total deformation also becomes 3.1739mm. The maximum value of total deformation becomes 0.18634mm at 3 kinds of the strength tests on back frame. By the study result of no excessive deformation and no fracture cushion frame and back frame at automotive seat, the sufficient rigidity and strength to guarantee the safety of passenger can be verified.

• Proceedings of the Korean Society of Soil and Groundwater Environment Conference
• /
• 2006.04a
• /
• pp.247-252
• /
• 2006

오염 퇴적물내 중금속의 방출과 이에 따른 생이용성(bioavalability)은 기존의 가역 평형관계로써 설명하기에 불충분한 것으로 알려져 있다. 최근 연구결과에 의하면 이러한 탈착 저항성을 설명하기 위한 비가역적 모델에 의해 퇴적물내 중금속의 탈착저항성 부분이 존재함이 밝혀졌다. 탈착저항성에 대해서는 아직 충분한 규명이 이루어지지 않았으나, 오염물질의 노화(aging)에 의해 일단 탈착저항성을 띠게 되면 생이용성(bioavailability)이 감소되는 것으로 알려져 있다. 본 연구에서는 노화(aging)가 연안 퇴적물 내 납과 카드뮴의 흡/탈착 특성에 미치는 영향을 알아보기 위해 연속 탈착실험과 biphasic 탈착모델을 적용함으로써 납과 카드뮴의 탈착저항성을 규명하고자 하였다. 그리고 연속 추출 실험을 통해서 노화(aging)에 따른 퇴적물 내 납과 카드뮴의 흡착 기작을 규명하고자 하였다. 연속탈착 실험 결과 시간이 경과함에 따라 탈착저항성부분의 크기가 증가하였으며, 연속추출 실험 결과 납의 경우 carbonate fraction에서 추출된 납이 가장 많았으며, 노화(aging) 따라 exchangeable fraction에서 추출된 납이 감소하는 반면 reducible, organic material, residual fraction에서 추출된 납의 양이 증가하였다. 카드뮴의 경우 가장 많은 양이 추출된 단계는 exchangeable fraction이였으며, organic material fraction에서는 카드뮴이 추출되지 않았다. 노화(aging) 따라 reducible fraction과 residual fraction에서의 추출량이 증가하는 경향을 보였으나 그 양은 매우 적은 것으로 나타났으며, 노화(aging)에 따른 exchangeable fraction과 carbonate fraction에서의 추출량은 큰 변화가 없었다. 대해서는 북한지역의 분포상황을 밝혔다.것을 알 수 있었으며, 크롬과 비소의 경우는 초기에 많이 용출되고, 구리의 경우는 꾸준히 용출되는 것을 알 수 있었다. 3년 된 통나무집이 8년 된 통나무집보다. 용출양이 더 컸으며, 이는 CCA성분이 초기에 많이 용출된다는 것을 의미한다. 억제 효과를 나타내었고 Hep3B에서는 부탄을 분획물 (1 mg/mL)에서 82%의 비교적 높은 성장억제효과를 나타내었다.as a "front" and "back". Thus, Germany′s private space may face a genuine public space and street, which is rare in the Korean housing. Although the layout of indoor space in the korean housing tends to be open, such an openness may be outstanding in living and dining spaces, kitchen and various accesses to rooms. In the case of Germany, such indoor spaces are usually closed to each other. Thus corridors act to separate these spaces. Such differences are analysed to be due to the different perceptions of interpersonal and socio-cultural attributes as intra-family and inter-neighbor relationships or communications. 알 수 있었다.도 질소와 인산처럼 토양지지대가 있는 경우가 낮은 함량을 유지하였다.pe from the daily life, to fantasize and daydre