• Economic and Environmental Geology
• /
• v.29 no.3
• /
• pp.315-323
• /
• 1996

An apatite drain was constructed on September 30, 1994 at the Green Valley Abandoned Coal Mine site near Terre Haute in west central Indiana. The primary objective of this experiment is to evaluate the long-term ability of the apatite drain to mitigate acid mine drainage (AMD) under field conditions. The drain 9 m long, 3.3 m wide, and 0.75 m deep, contain 95 rum to No. 30 mesh-size apatite ore (francolite) and receive AMD seepage from reclaimed gob piles, and designed according to the laboratory testing. The apatite drain was covered with limestone riprap and filter fabric to protect the drainage system from stormwater and siltation. The drain consists of about 50 metric tons of apatite ore obtained from a phosphate mine in Florida. A gabion structure was constructed downstream of the apatite drain to create a settling pond to collect precipitates. Apatite effectively removed iron up to 4,200 mg/l, aluminum up to 830 mg/l and sulfate up to 13,430 mg/l. The pH was nearly constant for the influent and effluent, ranging between 3.1 and 4.3. Flow rate measured at the gabion structure ranged from 3 to 4.5 l/m. Precipitates of iron and aluminum phosphate (yellow and white suspendid solids) continued to accumulate in the settling pond.

• Journal of the Korean Wood Science and Technology
• /
• v.13 no.3
• /
• pp.49-53
• /
• 1985

The effects of pre-treatments, the hot water extraction of wood meal and the addition of chemical ($CaCl_2$) to wood-cement water system on the properties of wood-cement composite such as modulus of rupture (MOR), modulus of elasticity (MOE), water sorption ratio and swelling ratio of resulting boards were studied in this experiment. The wood meals through 0.83mm(20 mesh) and retained on 0.42mm(35 mesh) screen were prepared from Pinus densiflora S. at Z. and Larix leptolepsis G. For hot water extraction, 500 grams of wood meal for each species were heated to boiling with 1,500ml of distilled water in 2-liter beaker for 6 hours. Every 2 hours, the wood meals were washed with boiling distil1ed water and reheated to boiling again. After 6 hours boiling, the boiled wood particles were collected by pouring this particles on 200 mesh screen. The collected particles then washed twice with hot distilled water and dried for 24 hours in an oven at $109{\pm}20^{\circ}C$. A mixture of 663.4 grams of cement with 331.7 grams of wood meal based on oven-dry weight were dry-mixed in a plastic vessel. The mixture was kneaded with 497.6ml of distilled water in the ratio of 1.5ml of water to a gram of wood meal. To add calcium chloride to the mixture as an accelerator, $CaCl_2$ 4% solution by weight per volume, was added to pine-or larch-cement board in the ratio of 3% to cement weight. To set wood-cement board, this mixture was clamped at 30cm ${\times}$ 30cm, in thickness of 1.5cm for 3 days at room temperature, declamped and then placed at open condition for 17 days. The target density was 1.0. The four specimens sized to 5cm in width and 28cm in length were used for MOR and MOE test for each treatment. After MOR test, the tested specimens were cut to the size of 5cm ${\times}$ 5cm for water sorption and swelling test. The twenty specimens used to measure the water sorption ratio (soaking 24 hours) and ten of these were used for swelling ratio measurement The results obtained were as follows: 1) Larch was not suitable for wood-cement boards because larch-cement board developed no strength, but pine showed 97.9kg/$cm^2$ by hot water extraction. 2) To increase MOR, hot water extraction was more effective than the addition of $CaCl_2$ in pine and larch because the $CaCl_2$ addition was seemed to speed up the ratio of cement hydration without reacting with the wood substances. 3) The water sorption ratio was lowered by the addition of $CaCl_2$ to wood-cement system because the chemical additive accelerated the rate of cement hydration. 4) In pine-cement board, the swelling ratio from 0.37 to 0.42 percent was observed in length and the swelling ratio from 0.88 to 2.0 percent in thickness. As a rule, the swelling ratio of wood-cement board was very low and the swelling ratio in thickness was higher than in length.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.8 no.1
• /
• pp.9-17
• /
• 2010

The LCC (Liquid Cadmium Cathode) structure to be developed for inhibiting the formation and growth of the uranium dendrite has been known as a key part in the electrowinning process for the simultaneous recovering of uranium and TRU (TRans Uranium) elements from spent fuels. A zinc-gallium (Zn-Ga) experimental system which is able to be functional in aqueous condition and normal temperature has been set up to observe the formation and growth phenomena of the metal dendrites on liquid cathode. The growth of the zinc dendrites on the gallium cathode and the performance of the existing stirrer type and pounder type cathode structure were observed. Although the mechanical strength of the dendrites appeared to be weak in the electrolyte and easily crashed by the various cathode structures, it was difficult to effectively submerge the dendrite into the bottom of the liquid cathode. Based on the results of the aqueous phase experiments, a lab-scale electrowinning experimental apparatus which are applicable to the development of LCC srtucture for the electrowinning process was established and the performance tests of the different types of LCC structure were conducted to prohibit the uranium dendrite growth on LCC surface. The experimental results of the stirrer type LCC structures have shown that they could not effectively remove the uranium dendrites growing at the inner side of the LCC crucible and the performances of the paddle and harrow type LCC structure were similar. Therefore a mesh type LCC structure was developed to push down the uranium dendrites to the bottom of the LCC crucible growing on the LCC surface and at the inner side of the crucible. From the experimental results for the performance test of the mesh type LCC structure, the uranium was recovered over 5 wt% in cadmium without the growth of uranium dendrites. After completion of the experiments, solid precipitates of the bottom of the LCC crucible were identified as an intermetallic compound (UCd11) by the chemical analysis.

• Applied Microscopy
• /
• v.10 no.1_2
• /
• pp.7-17
• /
• 1980

Electron microscope radioautography introduced by Liquier-Milward (1956) is now used routinely in many laboratories. Most of the technical difficulties in specimen preparation have been overcome. This method is modified from loop method for improvement of EM radioautographic techniques. The advantages of this method are: 1. the use of single specimens on small corks and of a large wire loop, allows the experimenter to avoid the blemishes in the membrane; 2. the surfactant dioctyl sodium sulphosuccinate is added to diluted ILford L4, thus greatly prolonging the period of time over which good emulsion layers can be made; 3. corks can be handled in perspex holder which allows about 20 specimens to be developed simultaneously. The steps of the method comprise: 1. Cut ribbons of ultrathin sections of silver interference colour 2. Pick them up on formvar-coated 200 mesh grids 3. Prestaining of tissues 4. Coat the specimens with a thin layer of carbon by evaporation (30-60A) 5. Mount the specimens on corks (about 1cm apical diameter) using double-sided scotch tape 6. Emulsion coating; a. Take a 250m1 beaker, place it on the pan of a sliding weight balance and weigh it. Add 10 grams extra to the beam. Add pieces of ILford L4 emulsion to the beaker until the balance is swinging freely. Add the 20ml of distilled water that was previously measured out. b. Surfactant dioctyl sodium sulphosuccinate is added to diluted ILford L4. 7. Prepare a series of membranes of gelled emulsion with the wire loop and apply one to each cork-borne specimen. 8. Put the specimens away to expose by pushing the corks into short length of PVC tubing, each tube having a small hole in the side 9. Place the tubes in small boxes together with silica gel. 10. Exposure 11. Developer - Kodak Microdol X for 3 minutes 12. Fixer - A perspex holder can be manufactured which allows 20 specimens to be developed simultaneously. 12. Fixer - 30% sodium thiosulfate for 10 minutes 13. Examination with Siemens Elmiskop 1A electron microscope

• Toxicological Research
• /
• v.16 no.2
• /
• pp.125-131
• /
• 2000

The ethanol extract of Rhus verniciflua Stokes (RVS), the Korean Lacquer tree, was subsequentely isolated and fractioned into two portions using distilled water (SED) and 99% ethanol (SEE) as elution buffers through silica gel column (4x28 em, 22 $\AA$. 28~200 mesh). To know the antioxidative effect of the RVS extracts, primary hepatocytes were exposed to hydroxyl radical generated by 20 mU/$m\ell$ glucose oxidase with SED or SEE for 4 hr. The addition of 100$\mu\textrm{g}$/$m\ell$ SED in culture medium showed good protection from glucose oxidase (GO)-mediated cytotoxicity of hepatocytes, showing approximately equivalent to control. When the hepatocytes were incubated with 100 $\mu\textrm{g}$/$m\ell$ SED or SEE only for 4 hr. the activities of cell-associated superoxide dismutase (SOD) and catalase were elevated up to 1.22 fold and 1.4 fold, respectively, compared to control. Further increase, 1.88fold in SOD activity or 1.64fold in catalase activity, was also observed when the hepatocytes were incubated with 100 units/$m\ell$ of commercial SOD or catalase for 4 hr. Moreover. the glucose oxidase-mediated cytotoxicity in cultured hepatocytes was generally reduced upon addition of lysate obtained from SED or SEE-stimulated hepatocytes in a dose-dependent manner. From these results, we suggest that, in cultured hepatocytes, RVS ethanol extract can efficiently reduce cytotoxicity induced by glucose oxidase and may increase the activity of cell-associated SOD and/or catalase, thereby preventing and/or scavenging superoxides and hydroxyl radicals in this experiment.

• Journal of Fisheries and Marine Sciences Education
• /
• v.26 no.2
• /
• pp.421-429
• /
• 2014

We investigated the feeding ecology of juvenile chum salmon (Oncorhynchus keta) during the critical early life stage prey selectivity of juvenile chum salmon during early marine migration in Korean waters at spring 2011. Salmon juveniles and zooplanktons were collected to draw with $20m{\times}5m$ gill net and $300{\mu}m$ mesh zooplankton net at each station on 11th-13th April n 2011. Collected zooplanktons were classified to 5 Phylum, 6 Class, 9 Order 17 Species in this study. Almost 76.4-100% species were classified to Phylum Arthropoda, dominant species was a species out of Hyperia galba of Order Amphipoda, Acartia spp and Paracalanus parvus of Order Calanoida. Collected salmon juveniles were grew up to average 4.7-5.4 cm fork length and average 1.0-1.5 g wet weight in whole station. Fish stomach content (mg/salmon) was heaver to 97.4, 82.4 and 63.2 mg wet weight/salmon in ST 2, 3, 4 than 20.4, 18.9 mg/salmon of ST 1, 5, because there are fish (sand eel, Hypoptychus dybowskii) and Krill (Euphausia) as prey in salmon stomach in ST 2, 3, 4. And ST 2, 3, 4 and 5 were dominated by Amphipoda as Hyperia galba, Themisto japonica and Gammarus sp., but ST 1 was dominated by copepod, because of absence of Amphipoda in the station. Therefore small Amphipoda as Hyperia galba was good prey for just released salmon juvenile in nature.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.14 no.2
• /
• pp.269-279
• /
• 1994

This paper concentrates on the finite element analysis of concrete structures considering the material nonlinearity and time-dependent structural behavior. Using the rotating crack model among the smeared cracking model, the structural behavior up to ultimate load is simulated, and concrete is assumed to be an orthotropic material. Especially to include the tension stiffening effect in bending behavior, a criterion based on the fracture mechanics concept is introduced and the numerical error according to the finite element mesh size can be minimized through the application of the proposed criterion. Besides, the governing equation for steel is systematized by embeded model to cope with the difficulty in modeling of complex geometry. Finally, to trace the structural behavior with time under cracked and/or uncracked section, an algorithm for the purpose of time-dependent analysis is formulated in plane stress-strain condition by the age-adjusted effective modulus method.

• Journal of the Korean Society for Precision Engineering
• /
• v.29 no.12
• /
• pp.1285-1289
• /
• 2012

This study has been focused on application of ELID lapping process for mirror-surface machining of sapphire wafer. Sapphire wafer is a superior material with optic properties of high performance as light transmission, thermal conductivity, hardness and so on. High effective surface machining technology is necessary to use sapphire as various usages. The interval ELID lapping process has been set up for lapping of the sapphire material. According to the ELID lapping experimental results, it shows that 12.5 kg of load for lapping is most pertinent to ELID lapping. the surface of sapphire can be eliminated by metal bonded wheel with micron abrasives and the surface roughness of 60 nmRa can be gotten using grinding wheel of 2,000 mesh in 4.5 um, depth of cut. In this study, the chemical experiments after ELID grinding also has been conducted to check chemical reaction between workpiece and grinding wheel on ELID grinding process. It shows that the chemical reaction has not happened as the results of the chemical experiments.

• Spatial Information Research
• /
• v.15 no.4
• /
• pp.363-370
• /
• 2007

This study has been carried for the development of the basic algorithm of helicopter navigation system based on TRN (Terrain Referenced Navigation) with information input from the GPS. The helicopter determines flight path due to Origination-Destination analysis on the Cartesian coordinate system of 3-D DTM. This system shows 3-D mesh map and the O-D flight path profile for the pilot's acknowledgement of the terrain, at first. The system builds TCF (terrain clearance floor) far the buffer zone upon the surface of ground relief to avid the ground collision. If the helicopter enters to the buffer zone during navigation, the real-time warning message which commands to raise the body pops up using Matlab menu. While departing or landing, control of the height of the body is possible. At present, the information (x, y, z coordinates) from the GPS is assumed to be input into the system every 92.8 m of horizontal distance while navigating along flight path. DTM of 3" interval has been adopted from that which was provided by ChumSungDae Co., Ltd..

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.11 no.5
• /
• pp.56-61
• /
• 2012

Several Visualization techniques have been applied in traffic information area. This work is the basic research for applying of interactive visualization techniques when the traffic information is provided to users. Design of interactive visualization techniques were applied to traffic information services. Previous studies for information visualization with interactive visualization techniques were investigated, and the traffic information services currently provided were analyzed. There are many types of interactive visualization techniques, but this study is mainly focused on selecting, querying, linking, filtering and rearranging techniques. The users can obtain the proper and more suitable information for theie needs, because each interactive visualization techniques support interaction between information and users. The traffic information which has one of interactive techniques can be more effective for decision making and utilization. More attention is given to interactive visualization of data and information techniques in transportation field. By this research, it is expected that traffic information services is more effective and can be a foundation work for various interactive visualization techniques in traffice inforamtion.