• Korean Journal of Computational Design and Engineering
• /
• v.22 no.1
• /
• pp.70-79
• /
• 2017

Weft straightener is an important process to control the final quality of the fabrics. It is needed to calibrate the distorted weft after dyeing process. During various fabric treatment processes, the fabric is almost done with heat treatment through a tenter machine. At this time, weft distortion is occurred with uneven tension distribution. Traditionally, photo sensor is commonly used to detect the weft distortion but it is not applicable for special fabric types such as twill, mesh, combi, etc. In this paper, a new method for detecting the weft distortion using camera is introduced. A new weft straightener simulator is also developed to test the ability of the proposed method. It is shown that the method can be applied for various fabric types.

• Journal of Powder Materials
• /
• v.2 no.2
• /
• pp.135-141
• /
• 1995

As the first step of study on fabrication of ceramic powders from phytoliths in rice, especially in rice husks, pulverization method of rice husks and the properties of milled rice husks were investigated. Impact methods, such as ball milling, were not meaningful for pulverizing elastic and thin fabric structure of rice husks. The most effective one was cutting method. In the present work, a rotating knife cutting method was applied to pulverizing rice husks. A 40-mesh screen was inserted under the rotating knives. The most portion of the milled powder was found in -50/+100 mesh section. Morphology of the milled rice husks revealed that the husks larger than 70 mesh were flake-like shape, at -70/+100 mesh section relatively equi-axed shape, at -170/+325 mesh section rod-like shape, and below 325 mesh section dust-like shape. Tap density of raw rice husks was about 0.1 $g/cm^3$, while those of milled rice husks were over $0.4 g/cm^3$. This meant that, for a given volume of reactor, raw material charge can be increased more that 4 times when using milled rice husks than unmilled one. True densities of unmilled and milled rice husks were higher than $1.4 g/cm^3$, and increased with decreasing milled sizes.

• Journal of IKEEE
• /
• v.23 no.3
• /
• pp.793-799
• /
• 2019

In this study, the diffusion process and the thermal energy distribution gradient of the sensor were confirmed by using the finite element analysis program (COMSOL) of the mesh method to analyze the thermal diffusion in the wearable fabric (Nylon) + MWCNT gas sensor. To analyze the diffusion process of thermal energy, the structure of the gas sensor was modeled in a two dimension plane. The proposed modeling was presented with the characteristic value for the component of the sensor, and the gas sensor designed using the mesh finite element method (FEM) was proposed and analyzed by suggesting the one-way partial differential equation in the governing equation to know the degree of thermal energy diffusion and the thermal energy gradient. In addition, the temperature gradient 10[K/mm] of the anode-cathode electrode layer and the gas detection unit was investigated by suggesting the heat velocity transfer equation.

• Fashion & Textile Research Journal
• /
• v.12 no.5
• /
• pp.676-682
• /
• 2010

Superior hydrophilic properties will allow varieties of polyester(PET) fiber materials, fabrics and industrial materials a broader scope of use. The purpose of this study was to investigate the effect of water-absorbent softener treatment on the end-use properties and the hand of polyester knitted fabrics. Two different fabrics were knitted for the summer ladies' outwear; PET jersey and PET mesh. Variables were softner treatment and stitch type(jersey and mesh). Mechanical properties of the fabric samples were measured by KES-FB system. From these, primary hand values(HV) were evaluated by the conversion equation (KW-403-KTU) and the total hand value(T.H.V.) was calculated according to the KN-304 Summer. Both water-absorbent softner treatment and stitch types affected mechanical properties and hand values of PET fabrics. Mesh were thicker than single jersey stitch. As they became thicker, tensile, shear, and compressional energy increased. It appeared that coefficient of friction of mesh stitch was larger than that of single jersey stitch. The coefficient of friction and the mean deviation of surface roughness were decreased by softener treatment. After softner treatment KOSHI and SHARI of the both PET jersey and PET mesh decreased. However, FUKURAMI values of PET jersey increased and that of PET mesh decreased. The T.H.V. of the treated PET jersey was lower than that of the untreated one, while the T.H.V. of the treated PET mesh was higher than that of the untreated one. Overall T.H.V. of the single jersey was better than that of the mesh before and after softner treatment.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.12 no.4
• /
• pp.611-619
• /
• 2008

2.5D Mapping system that embody in this paper can make new design by doing draping to live various texture and model picture image of fashion clothes by pattern, and can confirm clothes work to simulation without producing direction sample or product directly. Also, the system can support function that can forecast fabric design and state of end article exactly, and the system can bring competitive power elevation of fashion industry and cost-cutting effect by doing draping using database of fabric and model picture image. 2.5D Mapping system composed and embodied by mesh warp algorithm module, light and shade extraction and application module, mapping path extraction module, mesh creation and transformation module, and 2.5D mapping module for more natural draping. Future work plans to study 3D fashion design system that graft together 3D clothes technology and 3D human body embodiment technology to do based on embodiment technology of 2.5D mapping system and overcomes expression limit of 2.5D mapping technology.

• Journal of the Korea Fashion and Costume Design Association
• /
• v.21 no.3
• /
• pp.1-11
• /
• 2019

This study examined the cause of the phenomenon of shrinkage in machine-embroidered fabrics, specifically those made of thin and pliable fabrics. Four woven fabrics and two knitted fabrics were selected as samples for analysis. The fabrics selected were silk organza, flax linen, polyester chiffon, cotton batiste, polyester raschel mesh, and cotton jersey. The thickness and drapability of the fabrics were observed and the shrinkage of the various types of embroidered fabrics produced using satin & step stitch techniques were measured. Moreover, the correlation between the shrinkage of the machine-embroidered fabrics and the drapability of the original fabrics was analyzed. Also, the colorfastness of six embroidery yarns was determined. The results of the study are as follows: first, the shrinkage of machine-embroidered fabrics increased at a greater rate than in embroidered knitted fabrics as compared to rates in embroidered woven fabrics. Moreover, in terms of stitch techniques, there was a greater shrinkage rate when satin stitch was applied compared to step stitch. Second, the shrinkage rate of machine-embroidered fabrics decreased when a stabilizer was fused onto the fabric. The shrinkage rate also decreased for fabrics when fused with paper stabilizer compared to those without it, and the rate decreased at a greater amount with paper stabilizer as compared to alginate film. Third, since there was a strong correlation between the shrinkage rate of the embroidered fabric and the drapability ratio of the original fabric, it was generally the case that the more pliable the fabric was, the greater the shrinkage rate was when the fabric was embroidered. Fourth, while the embroidery yarns mainly used in machine-embroidery presented an overall excellent level of colorfastness, there was slight color migration of level 4 to level 5 when using viscose rayon.

• Journal of The Korean Digital Architecture Interior Association
• /
• v.7 no.2
• /
• pp.19-24
• /
• 2007

This study attempts to examine and to analyze the characteristics of transparent materials and its methods to apply in space. the ability to see through a physical element, whether it is clear glass, sandblasted acrylic, or a delicate fabric, can have a dramatic and sensory effect on the overall perception of a space. The various range of Transparent materials and product in glass, plastic, fabric, and grid now gives us the potential to maximize the flow of light in our enclosed space. This research will explore how transparent, translucent, and semi-opaque elements can be used within the interior with full range of see-through materials. The transparent materials can be divided in two level - as structural elements and as stylish accessories. A glass partition or floor, metal mesh stairs can create divisions or link one space to another while maintaining effective levels of natural light. there is also various level of products from glass chair to basin. With the enthusiasm for using transparent materials, transparent materials will be more decorative and powerful application while still maximize the highest possible flow of light.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.41 no.6
• /
• pp.1050-1059
• /
• 2017

Drying processes often cause knitted fabrics to shrink. This study obtains proper drying conditions for in the dryer use that can minimize knitted fabric shrinkage by investigating changes in shrinkage according to drying conditions. The experiment samples were all machine washable plain, mesh, and lacoste knitted fabrics made of 100% cotton. Samples were first washed in a washing machine on a normal cycle. They were then layered on a flat surface in an artificial climate chamber and dried for 24 hours at $20^{\circ}C$ and $40^{\circ}C$, respectively. Shrinkage was measured for 180 minutes at 30 minute intervals after washing. The comparison results of the shrinkage in the washing and drying process indicate that 80.0% and 23.0% shrinkage of plain knitted and lacoste knitted fabrics occurred during the washing process. As the samples dried, the shrinkage of the plain and lacoste knitted fabrics then rapidly increased after approximately 30.0% moisture content. The highest air drying shrinkage occurred over one cycle with insignificant changes in shrinkage after repeated treatments.

• Journal of Fashion Business
• /
• v.13 no.2
• /
• pp.78-86
• /
• 2009

When scouring and contraction finishing at $90^{\circ}C$ using Relaxer or Rotary Washer contraction and weight loss ratio in warp and weft directions were excellent. Also surface state of fabric after drying or sanding treatment was excellent without crease. Low melting polyester fabric showed a complete melting bond by heat setting(P/S) at above $160^{\circ}C$. The alkali hydrolysis reaction of polyester showed the breakpoint in the weight loss behavior test, polyester yarn showed a breakpoint ranging from 25% to 28%. This is due to the difference of the hydrolysis rate between regular polyester and soluble polyester. Initially the soluble polyester was eluted and micro-fibrillized 5 times faster than a regular polyester. At a later time, a regular polyester was reduced weight to impart a proper flexibility and drape property to the fabric. As a result of surface sanding finishing, the surface of interior fabric showed a surface state most stabilized when using Mesh No. 220 in mono 0.2d after elution finishing. When the rotation direction of sanding roller was pro-, pro-, pro-, and retro-direction, a directional effect of tuft was not shown, a writing effect as suede was exhibited and a surface state was even. Sublimation fastness was 3-4 class for polyester and 2-4 class for nylon. Light fastness 3-4 class after lapse of 100 hours and 2-4 class after lapse of 160 hours. Abrasion fastness was 3-4 class on wet and 4-5 class on dry Laundry fastness was 2-4 class. As such, the abrasion fastness is slightly reduced upon wetting and the use thereof for interior is excellent, whereas laundry fastness is slightly lowered.

• Proceedings of the Korean Fiber Society Conference
• /
• 2003.04a
• /
• pp.130-131
• /
• 2003

산업용 직물은 다른 건축재료에 비해 유연성이 크고 재료무게에 비해 카버하는 면적이 넓어서 장기적인 고정 건축물이 아닌 경우에 그 이용도가 늘어나고 있다. 이러한 산업용 직물의 주 기능은 예정 사용기간 동안 직물 양면사이의 압력을 견디는 일이 주 부하 모드이며 이 이차원구조를 유지하는 부분은 이 구조를 잡고 있는 부분이다. 그러나 직물의 일부가 파손되어 압력차를 유지하지 못하면 공압을 이용한 건축물의 순간적인 파괴로 연결된다. (중략)