• Nuclear Engineering and Technology
• /
• 제47권3호
• /
• pp.227-239
• /
• 2015

The thermal, mechanical, and neutronic performance of the metal alloy fast reactor fuel design complements the safety advantages of the liquid metal cooling and the pool-type primary system. Together, these features provide large safety margins in both normal operating modes and for a wide range of postulated accidents. In particular, they maximize the measures of safety associated with inherent reactor response to unprotected, doublefault accidents, and to minimize risk to the public and plant investment. High thermal conductivity and high gap conductance play the most significant role in safety advantages of the metallic fuel, resulting in a flatter radial temperature profile within the pin and much lower normal operation and transient temperatures in comparison to oxide fuel. Despite the big difference in melting point, both oxide and metal fuels have a relatively similar margin to melting during postulated accidents. When the metal fuel cladding fails, it typically occurs below the coolant boiling point and the damaged fuel pins remain coolable. Metal fuel is compatible with sodium coolant, eliminating the potential of energetic fuel-coolant reactions and flow blockages. All these, and the low retained heat leading to a longer grace period for operator action, are significant contributing factors to the inherently benign response of metallic fuel to postulated accidents. This paper summarizes the past analytical and experimental results obtained in past sodium-cooled fast reactor safety programs in the United States, and presents an overview of fuel safety performance as observed in laboratory and in-pile tests.

• Journal of Welding and Joining
• /
• 제35권3호
• /
• pp.15-20
• /
• 2017

In this paper, two types of assemblies using CNT-filled SACAs (with 0.03 wt% CNTs and without CNT) were prepared to investigate the influence of carbon nanotubes (CNTs) on the reliability properties of solderable anisotropic conductive adhesives (SACAs) with a low-melting-point alloy (LMPA). Two types of reliability test including thermal shock (TS: -55 to $125^{\circ}C$, 1000 cycles) and high-temperature and high-humidity (HTHH: $85^{\circ}C$, 85% RH, 1000 h) tests were conducted. The SACA assemblies with and without CNTs showed stable electrical reliability properties due to the formation of wide and stable metallurgical interconnection between corresponding metallizations by the molten LMPA fillers. Although the mechanical pull strength of CNT-filled SACA assemblies was decreased after thermal aging (because of the excessive layer growth and planarization of the IMCs), the CNT-filled SACA with 0.03wt% CNTs showed enhanced mechanical reliability properties compared with the SACA assemblies no CNTs. This enhancement in mechanical performance was due to the reinforcement effect of the CNTs. These results demonstrate that CNTs within the CNT-filled SACAs can improve the reliability properties of CNT-filled SACAs joints due to their superior physical properties.

• 한국미생물·생명공학회지
• /
• 제18권1호
• /
• pp.35-38
• /
• 1990

정제된 저해물질의 Rf치는 0.12-0.71 사이였으며 melting point는 154.3-155.3$^{\circ}C$로 나타났다. 물, formic acid, ethylene glycol monomethyl ether에는 용해되지만 그외 대부분의 용매에서는 불용성이었고 흡습성이 매우 큰 물질이었다. Phenol-sulfuric acid, ninhydrin, silvernitrate-sodium hydroxide 반응은 양성이었으나, DNS 반응에서는 음성이며 자외선 조사하에서 형광을 나타내었다. 저해물질의 구성성분은 fructose와 aspartic acid로 확인되었으며 분자량이 약 1,050 정도였다.

• Preventive Nutrition and Food Science
• /
• 제2권3호
• /
• pp.202-206
• /
• 1997

To develop mil fat fractions with desirable physico-chemical properties, anhydrous milk fat (AMF) was fractionated by one- and two-stage extractions using supercritical $CO_2$(SC-$CO_2$). Tow-stage extraction of AMF was performed by first producing tow fractions, an extract and a residue at 4$0^{\circ}C$/241bar, which were subsequently used as the feed for an extraction at 6$0^{\circ}C$/241bar and 4$0^{\circ}C$/345bar, and separated into five and four fractions, respectively, based one extraction time. These fractions were quantified and analyzed for fatty acids and physico-chemical properties. SHort-chain (C4~C8) fatty acids in extract fractions from an extract were 200~150% compared with those of the original AF. Long-chain (C14~C18) fatty acids in extract fractions from a residue were 118~141%. The ratio of unsaturated fatty acids in the residue fraction was 131%. Melting point ranged from 22 to 43$^{\circ}C$, iodine value 21.8 to 36.9, and saponification value 255 to 221 in the extract and residue fractions. SC-$CO_2$ fractionation of AMF by two-stage extraction offers the possibility of developing ractions with discrete fatty acid compositions and physico-chemical properties such as melting point, iodine value and saponification value.

• 한국산업융합학회 논문집
• /
• 제24권3호
• /
• pp.289-294
• /
• 2021

Tungsten (W) is used as a facing material for nuclear fusion reactors, and it is used in conjunction with structural materials such as copper alloy (CuCrZr), graphite, or stainless steel. On the other hand, since tungsten is a material with a high melting point, a method that can be manufactured at a lower temperature is important. Therefore, in this study, tungsten, which is a facing material, was attempted to be manufactured using a pressure sintering method. Material properties of sintered tungsten materials were analyzed for each solvent using two types of solvents, acetone and polyethylene glycol. The sintered tungsten material using acetone as a solvent exhibited a hardness value of about 255 Hv, and when polyethylene glycol was used, a hardness value of about 200 Hv was shown. The flexural strength of the sintered tungsten material was 870 MPa and 307 MPa, respectively, when acetone and polyethylene glycol were used as solvents. The sintered tungsten material using acetone as a solvent caused densification between particles, which served as a factor of increasing the strength.

• Nuclear Engineering and Technology
• /
• 제8권3호
• /
• pp.145-150
• /
• 1976

한천 원조인 꼬시레기를 여러 가지 선량의 코발트 60 감마선으로 조사하고 이에서 추출한 한천의 수율 및 특성을 조사하였으며 방사선조사한 한천분말의 품질과 비교하였다. 방사선조사한 원조에서의 한천의 수율은 조사선량이 2 Mrad 까지 상승됨에 따라 증가하였고 그 이상에서는 약간 감소하는 경향이었다. 한천의 젤화능력, 젤화점, 젤견고성 및 비점도는 1 Mrad까지 증가하였고 그이상에서는 감소하였으며 융점, 전질소, 조회분, 전유황 함량은 1 Mrad 까지 감소하였고 그 이상에서는 변화가 완만하였다. 시판용 한천분말의 방사선조사는 젤화능력, 비점도, 젤견고성의 급격한 감소와 젤화점, 융점의 완만한 감소를 가져왔다. 한천시료의 특성의 변화패던의 한천을 유리상태 또는 결합상태(해조중 존재형태)에서 조사하는가에 따라 달리 나타났다.

• Journal of Pharmaceutical Investigation
• /
• 제39권3호
• /
• pp.201-205
• /
• 2009

Triglyceride solid lipid with medium chain fatty acid, tricaprin (TC), was used as a core matrix of lipid nanoparticles (LN) to solubilize water-insoluble paclitaxel and enhance the stability of nanoparticles by immobilization of incorporated drug in the solid core during storage at low temperature. In the present study, TC-LN containing paclitaxel was prepared by hot melt homogenization method using TC as a core lipid and phospholipids as stabilizers. The particle size of TC-LN containing paclitaxel was less than 200 nm and its zeta potential was around -40 mV. Calorimetric analysis showed TC core could be solidified by freezing and thawing in the manufacturing process in which the hot dispersion should be prepared at elevated temperature and subsequently cooled to obtain solid lipid nanoparticles. The melting transition of TC core was observed at $27.5^{\circ}C$, which was lower than melting point of TC bulk. The particle size of TC-LN remained unchanged when kept at $4^{\circ}C$. Paclitaxel containing TC-LN showed comparable anticancer activity to the Cremophore ELbased paclitaxel formulation against human ovarian (OVCAR-3) and breast (MCF-7) cancer cell lines. Thus, lipid nanoparticles with medium chain solid lipid may have a potential as alternative delivery system for parenteral administration of paclitaxel.

• 수산해양기술연구
• /
• 제44권4호
• /
• pp.362-369
• /
• 2008

The snow melting system by electric heating wires which is adopted in this research is a part of road facilities to keep surface temperature of the road higher than freezing point of water for melting the snow accumulated on it. The electric heating wires are buried under paved road at a certain depth and operated automatically and manually. Design theory, amount of heating, and installation standard vary according to economic situation, weather condition, installation place and each country applying the system. A main purpose of this study is figuring out the appropriate range of required heat capacity and installation depth and pitch for solving snowdrifts and freezing problems with minimum electric power consumption. This study was performed under the ambient air temperature($-2^{\circ}C$, $-5^{\circ}C$), the pitches of the electric heating wires(200 mm, 300 mm), heating value($250\;W/m^2$, $300\;W/m^2$, $350\;W/m^2$).

• 한국군사과학기술학회지
• /
• 제14권5호
• /
• pp.897-903
• /
• 2011

The objective of this study is to investigate the thermal behavior on material surface and the variation in the surface morphology of aluminum 6061 alloy by the Nd:YAG pulsed-laser irradiation. First, we predicted the surface temperature variation during pulsed-laser irradiation by using the two dimensional finite element analysis. When the pulsed-laser of 133 mJ energy and 5 ns pulse duration is irradiated on the surface of aluminum alloy, the material surface is thought to be melting because the surface temperature rises steadily up to about $660^{\circ}C$ exceeding the melting point. Also, the experimental results show that the solidification microstructure has been developed clearly after surface melting. Second, the diameter of melted zone was analysed by finite element analysis and measured by OM(Optical Microscopy). It increased logarithmically with increase in the number of laser irradiation. In addition, AFM(Atomic Force Microscopy) measurement showed an increase in the average surface roughness during pulsed-laser irradiation.

• 전기학회논문지
• /
• 제57권1호
• /
• pp.46-51
• /
• 2008

Extra-high voltage(EHV) disconnecting switch(DS) consists of the electrical contacts and mechanical parts which actuate the contacts. When the short-circuit condition occurs, a large amount of current flows through the electrical contact in disconnecting switches and this causes considerable temperature rise due to Joule heating. If the temperature rise is higher than the melting point of contact material, the DS contact becomes melting and cannot be usable anymore. For this reason, the analysis for capability of carrying short-circuit current in DS contacts must be performed at a design stage. Here, we proposed a numerical technique for evaluating the capability of carrying short-circuit current at electrical contacts in EHV DS. In this numerical approach, the mechanical and thermal analyses were simulated to check the capability of carrying short-circuit current. First, the applied pressure at contact parts was analyzed considering the mechanical properties, and then contact resistance was calculated by an empirical equation. Finally, thermal analysis was performed with resistance variation at electrical contacts. To verify these numerical results, the distributions of temperature in DS were experimentally measured and compared with each other. The results from experiments were agreed well with those from the proposed numerical simulations.