• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.26 no.7
• /
• pp.301-307
• /
• 2014

This paper presents a numerical study on the constrained melting of a phase change material inside various capsule containers, using water and HDPE (High Density Polyethylene) as a PCM and a capsule material, respectively. The computations are based on an iterative, finite-volume numerical procedure that incorporates a single-domain enthalpy formulation for simulation of the phase change phenomenon. Using the enthalpy method, various capsule configurations, such as a capsule from E company, an isochoric cylinder capsule, an equivalent diameter sphere capsule, and an isochoric sphere capsule, are used to investigate the effect of capsule configurations on the charging and discharging performance. A transient three-dimensional model is used for each case. The simulation results show that the capsule from E company results in a higher melting and solidification rate of the PCM, than the other capsule configurations considered in this research.

• Proceedings of the International Microelectronics And Packaging Society Conference
• /
• 2000.04a
• /
• pp.74-79
• /
• 2000

In an attempt to estimate the wetting properties of wettable metal layers by wetting balance method, an analysis of wetting curves of the coating layer was performed. Based on the analysis, wetting properties of UBM-coated Si-plate were estimated by the new wettability indices. The wetting curves of the one and both sides-coated UBM layers have the similar shape and show the similar tendency to the temperature. So the wetting property estimation of one side coating is possible with wetting balance method. For UBM of Si-chip, Cr/Cu/Au UBM is better than Ti/Ni/Au in the point of wetting time. At general reflow temperature, the wettability of high melting point solders(Sn-Sb, Sn-Ag) is better than that of few melting point ones(Sn-Bi, Sn-In).The contact angle of the one side coated plate to the solder can be calculated from the farce balance equation by measuring the static state force and the tilt angle.

• KIEAE Journal
• /
• v.17 no.3
• /
• pp.107-112
• /
• 2017

Purpose: Both silica gel and activated carbon black particles were adopted for use as PCM absorbed porous media applicable as construction materials. To investigate usable methods for absorbing PCM into the media, they were soaked into PCM and also tested for enhancement of PCM absorption into them. Method: To test PCM absorption into some porous media such as both ${\varphi}1{\sim}2mm$ and $10{\mu}m$ silica gels, and $50{\mu}m$ activated carbon black, $43^{\circ}C$ PCM was used as a laten heat material. The method, soaking into PCM was applied to this study, and the media were moderately rotated by centrifuge to have the extra PCM flow out. DSC analysis was conducted to investigate the melting and solidifying of the PCM absorbed into the porous media. Result: It was found that PCM was absorbed into the porous media by over 85 wt% of all particles. In addition, it was noted that the ultrasonic vibrator was accelerating the PCM absorption into the particles to three times higher speed than simple soaking. Centrifuge was adopted to remove extra PCM sticking on the particle surfaces and extra PCM was moderately removed from the surfaces of the particles. DSC analysis indicated that the latent heat of the absorbed PCM particles was 160 J/g, and the melting temperature was approximately $40^{\circ}C{\sim}50^{\circ}C$.

• Resources Recycling
• /
• v.12 no.4
• /
• pp.44-50
• /
• 2003

Separation of mixed plastics is not a simple task due to similarities of specific gravity and limitations of sizes, etc. In this study, a new technique was developed to separate plastics selectively by a thermal adhesion method using the different softening or melting temperatures of various types of plastics. Tests were conducted to investigate softening or melting temperatures and adhesion probabilities of plastics with change in temperature. Tests also were conducted to analyze the operating variables, including contact times, size and color pigment. It was founded that LDPE, HDPE and PVC, PET, etc among mixed plastics could be separated selectively according to the change of temperature.

• Korean Journal of Heritage: History & Science
• /
• v.44 no.3
• /
• pp.112-131
• /
• 2011

This article reports the results of scientific analysis using SEM-EDX, XRD, TG/DTA, performed on 5 green glaze samples of the brick and roofing tile excavated from the Sacheonwang temple site in Gyeongju in order to verify the chemical compositions and melting temperature. The glaze samples on 2 clay statues have similar chemical composition (PbO 74~81%, $SiO_2$ 14~18%) and melting temperature range ($970{\sim}1070^{\circ}C$), whereas the 2 tiles of goblin's face and 1 rhomb brick have different characteristics. Sample SC 003 (made of PbO 63~67%, $SiO_2$ 25~28%), one of the tiles of goblin's face, shows low melting temperature range (below $970^{\circ}C$), and sample SC 004 (composed of PbO 64~70%, $SiO_2$ 19~25% and melting point $970{\sim}1070^{\circ}C$), the other tile of goblin's face, shows different chemical characteristics compared with 2 clay statues. The green glaze on rhomb brick shows different composition compared with all the others from Sacheonwang temple site in that it does not show any impurity elements other than the main components (PbO 87~88%, $SiO_2$ 12~13%) with very low melting temperature range ($750{\sim}770^{\circ}C$). Surprizingly, the chemical and optical characteristics of this green-glaze on rhomb brick are very similar to that on the bricks from Yeongmyo temple site, Gyeongju. The above results indicate that raw material and manufacturing method are not same for 5 green-glaze samples from Sacheonwang temple site and therefore suggests that further study on the provenance of raw material such as lead isotope analysis is necessary. Our work will provide basic data for future reproduction study of green glazed brick of Sacheonwang temple site, Gyeongju and will also serve as a reference data for the study of raw material and manufacturing method of green glaze from other sites of cultural assets.

• Journal of the Korean Ceramic Society
• /
• v.25 no.5
• /
• pp.443-448
• /
• 1988

Colored Cubic Zircona(CCZ) single crystals were grown by the skull melting method. The grown crystals were doped with up to 0.1wt% transition (Cu, Ni, Co, Ti, Fe, Mo, Cr, V, Mn) metal ions on ZrO2-Y2O3(9.5~10mol%) and their Optical transmission spectra(λ=300~800nm)data were obtained. Various colors were pronounced due to dopant effects in the grown Crystals.

• Journal of the Korean Ceramic Society
• /
• v.26 no.5
• /
• pp.661-669
• /
• 1989

The defect structure in LiNbO3 single crystals grown by Czochralski method from the congruently melting composition were investigated. Chemical etching patterns were studied in x-plane, z-plane, and major cleavage plane, respectively, dislocation density was higher at the periphery of crystals than at the center because the thermal stress due to radial temperature gradient had a main effect on it, as compared with dislocations formed from the solid-liquid interface. Many dislocation lineages were arranged along several directions.

• 제어로봇시스템학회:학술대회논문집
• /
• 1987.10b
• /
• pp.597-602
• /
• 1987

This paper proposes a voltage-fed high frequency resonant inverter having variable voltage variable frequency(VVVF) control function. VVVF control is performed by PWM-TRC method in the boost type chopper and PFM-TRC method in the high frequency resonant inverter. This circuit is suitable for induction heating and melting power supply in industry. The operating characteristics of this inverter are discussed from a theoretical point of view. The results of operating characteristic analyses are given leading to complete designing data.

• Proceedings of the Optical Society of Korea Conference
• /
• 1999.08a
• /
• pp.220-221
• /
• 1999

Single crystals of Yttrium Calcium Oxyborate (YCOB) doped with different concentrations of Er3+ and Yb3+ ions were growth by Czochralski method. High qualities of crystals in morphology and transparency were obtained . Analysis on crystal structure and lattice parameters were performed by X-ray diffraction method. It was found that congruent melting composition is YCA4.2O1.2(BO3)3. Absorption and fluorescence properties of grown crystals were also reported.

• YAKHAK HOEJI
• /
• v.13 no.2_3
• /
• pp.80-83
• /
• 1969

Acetylsalicylic acid gives a water-insoluble violet complex with $<\alpha>$-Picolin-Cu(II) reagent. The Complex is extractable well with a mixture of $<\alpha>$-Picolin-tetrachloromethane solution. The Complex salt dissolved in the mixed solution shows a maximum absorption at 620 m$<\mu>$. It has a melting point at $171^{\circ}C-$173^{\circ}C and molar ratio of Acetylsalicylic acid: Cu(II): $<\alpha>$-Picolin was estimated as 2:1:2 by continuous variation method and chelate titration method.