• 한국광학회지
• /
• 제25권5호
• /
• pp.273-278
• /
• 2014

일련의 국부영역으로부터 이차미분값을 획득하여 전체 형상을 복원하는 측정법을 제안하였다. 측정시 기울기가 제거된 국부형상에 대해 곡률과 이차미분이 동일시 되는 점을 이용하여, 3개의 이차미분값으로부터 직교하는 2방향을 따라 3차원형상을 복원할 수 있는 알고리즘을 구현하였다. 임의로 발생시킨 Zernike다항식의 계수로 자유곡면형상을 생성시키고, 구현된 알고리즘을 적용함으로써 검증과정을 수행하였다. 적용한 결과 최대 0.8 mm Sag를 갖는 직경 200 mm영역의 자유곡면형상에 대해 RMS 19 nm 형상복원오차를 갖고 복원됨을 확인하였다. 측정오차에 대한 복원오차 민감도를 진단하기 위해 SNR(Signal-to-Noise Ratio) 16의 가우시언 랜덤 노이즈를 부여한 후, 복원되는 형상의 오차를 진단한 결과, 197 nm의 형상복원오차가 발생함을 확인하였다.

• 치과방사선
• /
• 제28권1호
• /
• pp.215-224
• /
• 1998

The following conclusions were obtained from the non-reconstructed and reconstructed subtraction images of the standard intraoral radiographs which were taken with paralleling technique with Rinn XCP only and with occlusal bite registration for geometric standardization using bilateral mandibular premolar and molar regions of two dry human skulls. 1. The SD of the overall subtraction images of the premolars and molars of the non-reconstructed, that is, the manual superimposition showed statistically significant difference between the non-registered and registered groups. 2. In non-reconstructed and non-registered cases, the quality of the subtraction images were improved when superimposition was focally done and this was more evident in areas where the radiographic images tend to be distorted due to anatomic reasons. 3. In non-reconstructed and registered cases, the subtraction images were consistent regardless of the anatomic site or the focus of superimposition. This means that the geometric standardization with only occlusal bite registration could produce serial radiographs which is suitable for subtraction. 4. The SD of the overall subtraction images of the premolars and molars of the reconstructed, that is, the automatic superimposition showed statistically insignificant difference between the non-registered and registered groups. This means that using reconstruction, subtraction radiography is possible without occlusal bite registration. 5. In reconstructed and non-registered cases, compatible quality of the subtraction images were obtained regardless of the anatomic site or area of the corresponding points. 6. In reconstructed and registered cases, best subtraction images whose quality showed sensitivity to the areas of corresponding points were obtained.

• 전기전자학회논문지
• /
• 제21권4호
• /
• pp.338-347
• /
• 2017

본 논문은 TDL(전술 데이터 링크)의 항공용 단말의 구성품인 고출력증폭기의 설계 및 제작에 관해 기술하였다. 동일한 주파수 대역을 사용하는 레이다 및 다른 통신장비와 한정된 주파수 자원을 효율적 사용이 가능하도록 고속주파수도약기술, 인지무선기술, 수신필터뱅크 기술을 적용하였다. 고출력증폭기는 물리적으로 송신부, 수신부, 기구부, 케이블조립체로 구성되며, 최대 전송 거리, 수신감도 등의 전기적 특성과 온도 특성을 충족하도록 설계되었다. 고출력증폭기의 요구 규격을 만족하기 위해 모델링 및 시뮬레이터를 이용하였다. 송신 출력과 잡음 지수는 각각 50.02dBm 및 2.682dB로 측정되었다. 전기적 특성 시험 및 환경 특성 시험으로 요구 규격을 모두 만족함을 확인하였다.

• 복식문화연구
• /
• 제13권4호
• /
• pp.550-563
• /
• 2005

These days, photoshop and illustrator program can make a fashion illustration express easily and speedily, And they can also express a feeling and sensitivity of fashion illustrator by a tool and effect more than a manual work's media. The purpose of this study was to analyze a visual expression and characteristics in fashion illustration using 2D graphics. The method of this study was to analyze the fashion illustration books using 2D graphics. The visual expressions in fashion illustration using 2D graphics were as follows: Fashion illustration was based on a sketch or photography, and used a composition, drawing, mapping, painting, and manual work's re-touching. Characteristics of visual expression were as follows: First, a image composition was showed discontinuity and heterogeneity of image, new context and composition, and allowance of reality. Second, image transform was showed image overlap, body transformation by image recomposition, and deformed transformation by vector drawing. Third, hyper-real was showed precise touching, mechanical and neutral image, omission of background and focus of an object's characteristic and information. Fourth, following a realistic expression was showed simplified color, shading, dominant view point of fashion illustrator by omission, and daily lift style. Fifth, following a pictorial expression was showed non-fixed and irregular line, natural painting, and drawing and painting by conventional pictorial media. In conclusion, a photoshop and illustrator in 2D graphics will serve as a new media far fashion illustration with a manual work. And they will not only intensify a capacity as a commercial role of fashion illustration but also present a positive motive for students learning a fashion illustration.

• 한국재료학회지
• /
• 제25권10호
• /
• pp.559-565
• /
• 2015

The ductile-brittle transition behavior of two austenitic Fe-18Cr-10Mn-N-C alloys with different grain sizes was investigated in this study. The alloys exhibited a ductile-brittle transition behavior because of an unusual brittle fracture at low temperatures unlike conventional austenitic alloys. The alloy specimens with a smaller grain size had a higher yield and tensile strengths than those with a larger grain size due to grain refinement strengthening. However, a decrease in the grain size deteriorated the low-temperature toughness by increasing the ductile-brittle transition temperature because nitrogen or carbon could enhance the effectiveness of the grain boundaries to overcome the thermal energy. It could be explained by the temperature dependence of the yield stress based on low-temperature tensile tests. In order to improve both the strength and toughness of austenitic Fe-Cr-Mn-N-C alloys with different chemical compositions and grain sizes, more systematic studies are required to understand the effect of the grain size on the mechanical properties in relation to the temperature sensitivity of yield and fracture stresses.

• Journal of Electrical Engineering and Technology
• /
• 제3권2호
• /
• pp.224-234
• /
• 2008

Multi-phase machines can be used in variable speed drives. Their applications include electric ship propulsion, 'more-electric aircraft' and traction applications, electric vehicles, and hybrid electric vehicles. Multi-phase machines enable independent control of a few numbers of machines that are connected in series in a particular manner with their supply being fed from a single voltage source inverter(VSI). The idea was first implemented for a five-phase series-connected two-motor drive system, but is now applicable to any number of phases more than or equal to five-phase. The number of series-connected machines is a function of the phase number of VSI. Theoretical and simulation studies have already been reported for number of multi-phase multi-motor drive configurations of series-connection type. Variable speed induction motor drives without mechanical speed sensors at the motor shaft have the attractions of low cost and high reliability. To replace the sensor, information concerning the rotor speed is extracted from measured stator currents and voltages at motor terminals. Open-loop estimators or closed-loop observers are used for this purpose. They differ with respect to accuracy, robustness, and sensitivity against model parameter variations. This paper analyses operation of an MRAS estimator based sensorless control of a vector controlled series-connected two-motor five-phase drive system with current control in the stationary reference frame. Results, obtained with fixed-voltage, fixed-frequency supply, and hysteresis current control are presented for various operating conditions on the basis of simulation results. The purpose of this paper is to report the first ever simulation results on a sensorless control of a five-phase two-motor series-connected drive system. The operating principle is given followed by a description of the sensorless technique.

• 한국전기전자재료학회논문지
• /
• 제29권1호
• /
• pp.23-29
• /
• 2016

In this paper, in order to quantify the peristalsis occurrence in a guinea pig's large intestine, a miniaturized air-gap capacitive pressure sensor was fabricated through micro-electro-mechanical system (MEMS). The proposed pressure sensor is a two-layered biocompatible polyimide substrate consisting of an air-gap capacitive plates between the substrates. The proposed pressure sensor was designed with a careful consideration of the structure and motility mechanism of the guinea pig's large intestine. Artificial pellets were mounted on a prototype pressure sensor to provide some redundancies in the form of size and shape of the guinea pig feces. Capacitance of a prototype sensor was recorded to be 2.5 ~ 3 pF. This capacitance value was later converted to count value using a lab fabricated data conversion system. Sensitivity of the pressure sensor was recorded to be below 1 mmHg per atmospheric pressure. During in vivo testing, artificial peristalsis caused by drug injection was measured by inserting the prototype pressure sensor into the guinea pig's large intestine and pressure data obtained due to artificial peristalsis was graphed using a labview program. The proposed pressure sensor could measure the pressure changes in the proximal, medial, and distal parts of the large intestine. The results of the experiment confirmed that pressure changes of guinea pig's large intestine was proportional to the degree of drug injection.

• 실천공학교육논문지
• /
• 제6권2호
• /
• pp.105-110
• /
• 2014

본 연구에서는 강한 내구성을 지닌 자동차 타이어용 압력센서를 개발하기 위해 박막 물질로서 적용될 티타늄 멤브레인의 기계적 특성이 연구되었다. 제작공정으로 기존의 마이크로 머시닝공정과 적층 공정기술이 동시에 적용되었으며, 티타늄 멤브레인 기반의 압력 센서가 설계, 제조 및 특성화 되었다. 마이크로 머시닝 공정을 통한 티타늄 멤브레인과 기판의 접합 제조과정은 30분 동안의 20 MPa의 압력과 $200^{\circ}C$의 온도과정 후 $24^{\circ}C$에서의 냉각으로 진행된다. 각각의 압력센서 표면은 니켈 도금된 후방전극이 기판 위에 마이크로 소자로 조립되었다. 제작과정에서 발생한 잔류응력을 예측하기 위해 유한요소 해석이 적용되었다. 또한 티타늄 멤브레인의 외부 압력하에서 변형에 의한 처짐이 계산되었다. 제작된 장치의 민감도는 $10.15ppm\;kPa^{-1}$ 였고 이때의 정전용량 변화량은 0.18 pF, 압력 범위는 0-210 kPa 였다.

• 한국가스학회지
• /
• 제17권5호
• /
• pp.28-36
• /
• 2013

에너지 보안의 위기를 타파하기 위한 가장 많은 관심을 가지고 있는 것 중 하나가 지중 속 매장되어 있는 석탄이다. 본 연구에서는 지중에서 석탄을 직접 채굴을 하지 않고 지중 내 석탄 가스화를 직접 진행할 수 있는 지중 석탄가스화 공정에 대하여 화학 반응 공정 모사를 진행하였다. 본 연구는 1980년대 말에 미국의 Rocky Mountain 1 지중 석탄가스화 프로젝트를 참고로 진행을 하여 기본 모델을 완성하였다. 그리고 산화제 주입조건에 따른 민감도 분석을 통하여 합성가스의 조성 결과를 확인하였다. 반응 모델은 건조, 열분해, 촤 가스화로 나누어 모델이 구현되었고 실제 실험값에서의 생산된 가스량, 가스화 된 탄소량, 가스 수율 등의 값으로 결과를 확인하였다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2005년도 하계학술대회 논문집 Vol.6
• /
• pp.369-370
• /
• 2005

LTCC (Low Temperature Cofired Ceramic) technology is one of technologies which can realize SIP (System-In-a-Package). In this paper realization of gas sensor using LTCC technology was described. In the conventional gas sensor structure, wire bonding method is generally used as an interconnection method whereas in the LTCC sensor structure, via was used for the interconnection. As sensing materials, $SnO_2$ was adopted. The effect of frit glass portion on the adhesion of the sensing material to the LTCC substrate and the electrical conductivity of the sensing material were analyzed. AgPd, PdO, Pt was added to the sensing material as an additive for improving the gas sensitivity and electrical conductivity and the effect of the amount of additives in the sensing material on the electrical conductivity was investigated. The effect of the amount of frit glass in the termination on the sensor performance, especially mechanical integrity, was considered and the crack initiation and propagation in the boundary between the sensing material and the termination was studied.