• Journal of the Korean Institute of Gas
• /
• v.24 no.5
• /
• pp.29-38
• /
• 2020

It is practically difficult to accurately measure the temperature and concentration of a large combustion systems at industrial sites in real time. Temperature measurement using thermocouple, which are mainly used, is a point-measuring method that is less accurate and less reliable to analyze the wide area range of inner combustion system, and has limitations to internal accessibility. In terms of concentration analysis, most measurement methods use sampling method, which are limited by the difficulty of real-time measurement. As a way to overcome these limitations, laser-based measurement methods have been developed continuously. Laser-based measurement are line-average measurement methods with high representation and precision, which are beneficial for the application of large combustion systems. In this study the temperature and concentration were measured in real time by water vapor and oxygen generated during combustion using Tunable Diode Laser Absorption Spectroscopy (TDLAS). The results showed that the average temperature inside the combustion system was 1330℃ and the mean oxygen concentration was 3.3 %, which showed similar tendency with plant monitoring data.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.21 no.2
• /
• pp.189-196
• /
• 2001

Photoelasticity is one of the most widely used methods for whole field stress analysis. In photoelasticity, the difference and the directions of the principal stresses we given isochromatic and isoclinic fringe patterns. Conventionally, principal stress directions are measured manually by relating the polarizer and analyzer of a plane polariscope at the same time. This is known to be the Tardy compensation method. This measurement can be very tedious and time consuming in whole field analysis. It is not possible to separate isoclincs from photoelastic fringes by conventional photoelastic technique. In this study, photoelastic theory is represented by Jones matrices and 4-steps and 8-steps phase shifting methods are described A feasibility study using computer simulation is done to separate isoclincs and isochomatics from photoelastic fringes of a circular disk under diametrical compression. Fringe patterns of the disk are generated using stress optic law. The magnitudes of isoclincs and isochromatics obtained from 8-step phase shifting method are compared with those of theories. From computer simulation, it is verified to separate isoclincs and isochomatics from photoelastic fringes.

• Journal of the Korean Wood Science and Technology
• /
• v.41 no.4
• /
• pp.346-357
• /
• 2013

In this study, it was conducted to produce wood pellets using domestic forest thinning residues and examine their quality according to Korean pellet quality standard. Raw materials were composed of larch and mixed broad leaves species. Based on the small-end diameter (6 cm), they were classified into four different types of raw materials such as LM (larch with middle diameter), LS (larch with small diameter), MM (mixed broadleaf with middle diameter), and MS (mixed broadleaf with small diameter). After crushing and drying process, wood pellets were produced by a ring-die type pelletizer using each raw material. Wood pellets made from four different types of raw materials were tested for their quality such as calorific value, moisture content, ash content, inorganic matters and so on. As results of quality analysis, the calorific values of all wood pellets were higher than 198 kcal/kg, and satisfied with the first grade of Korea wood pellet standard. The ash content was slightly increased after pelletizing. Mechanical durability of wood pellets was highly dependent on the types of raw materials. The quality differences among wood pellets were turned out due to different physical and chemical characteristics of raw materials even though the same pelletizing condition was applied.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.642-642
• /
• 2013

Graphene, two dimensional single layer of carbon atoms, has tremendous attention due to its superior property such as high electron mobility, high thermal conductivity and optical transparency. Especially, chemical vapor deposition (CVD) grown graphene has been used as a promising material for high quality and large-scale graphene film. Unfortunately, although CVD-grown graphene has strong advantages, application of the CVD-grown graphene is limited due to ineffective transfer process that delivers the graphene onto a desired substrate by using polymer support layer such as PMMA(polymethyl methacrylate). The transferred CVD-grown graphene has serious drawback due to remaining polymeric residues generated during transfer process, which induces the poor physical and electrical characteristics by a p-doping effect and impurity scattering. To solve such issue incurred during polymer transfer process of CVD-grown graphene, various approaches including thermal annealing, chemical cleaning, mechanical cleaning have been tried but were not successful in getting rid of polymeric residues. On the other hand, lithographical patterning of graphene is an essential step in any form of microelectronic processing and most of conventional lithographic techniques employ photoresist for the definition of graphene patterns on substrates. But, application of photoresist is undesirable because of the presence of residual polymers that contaminate the graphene surface consistent with the effects generated during transfer process. Therefore, in order to fully utilize the excellent properties of CVD-grown graphene, new approach of transfer and patterning techniques which can avoid polymeric residue problem needs to be developed. In this work, we carried out transfer and patterning process simultaneously with no polymeric residue by using a metal etch mask. The patterned thin gold layer was deposited on CVD-grown graphene instead of photoresists in order to make much cleaner and smoother surface and then transferred onto a desired substrate with PMMA, which does not directly contact with graphene surface. We compare the surface properties and patterning morphology of graphene by scanning electron microscopy (SEM), atomic force microscopy(AFM) and Raman spectroscopy. Comparison with the effect of residual polymer and metal on performance of graphene FET will be discussed.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.4 no.1
• /
• pp.41-50
• /
• 2006

In this paper, sets of engineering analyses were conducted to renew the overall dimensions and configurations of a disposal container proposed as a prototype in the previous study. Such efforts and calculation results can provide new design variables such as the inner basket array type and thickness of the outer shell and the lid & bottom of a spent nuclear fuel disposal container. These efforts include radiation shielding and nuclear criticality analyses to check to see whether the dimensions of the container proposed from the mechanical structural analyses can provide a nuclear safety or not. According to the results of the structural analysis of a PWR disposal container by varying the diameter of the container insert, the Maximum Von Mises stress from the 102 cm-container meets the safety factor of 2.0 for both extreme and normal load conditions. This container also satisfies the nuclear criticality and radiation safety limits. This decrease in the diameter results in a weight loss of a container by $\sim20$ tons.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.9 no.1
• /
• pp.23-32
• /
• 2011

An engineering scale test, which is called KENTEX, was carried out to understand and to analyze the coupled thermal, hydrological and mechanical phenomena in the engineered barrier system(EBS) of Korean reference disposal system. Using the experimental data obtained from KENTEX, the water saturation processes in bentonite could be analyzed. From the comparison between the model calculation using ABAQUS and the experimental results, the difference of the water content between them in the unsaturating part was large because the drying phenomena due to moisture redistribution by the temperature gradient could not be included in the model. In the saturating part, the difference of the water content between them was decreased gradually and showed to be small in the full saturation. And the time of about 95% saturation could be estimated about 500 days from the model calculation and experimental results. Also it could be known that the moisture redistribution in the unsaturated part could not be affected on the saturation time of bentonite in the repository. Therefore, it is considered that this model could be used to quantitatively predict the water saturation time in bentonite as EBS for the disposal system.

• Applied Biological Chemistry
• /
• v.46 no.2
• /
• pp.113-116
• /
• 2003

Color value, total color difference $({\triangle}E)$, puncture strength (PS), tensile strength (TS), percent elongation(%E) at break values, and water vapor permeability (WVP) were determined for water-soluble chitosan films added with soy protein isolate (SPI) and $CaCl_2$. Mechanical and water vapor barrier properties of the chitosan films were affected by SPI and $CaCl_2$ concentrations. PS value $(174.5-448.8\;g_f)$ of the chitosan films increased with increasing concentration of $CaCl_2$ TS value of 0.05% $CaCl_2$-added chitosan films significantly increased to 1.58 MPa compared to 0.06 MPa of the control. %E values ranged from 12.25 to 44.80% and increased with increasing concentration of $CaCl_2$. WVP of $CaCl_2$-added films was lower than that of SPI-added films.

• Journal of the Korean Society of Environmental Restoration Technology
• /
• v.19 no.6
• /
• pp.77-86
• /
• 2016

Due to aging of the rural and mountain populations the labor force is reduced. However work intensity continues to increase, thus, there is a need to improve the current effectiveness of forest operations. This study compared and analyzed the Operation productivity and efficiency of planting containerized seedlings using a battery-powered planting auger and a mattock. Growth was also investigated by looking into the initial growth increments in the planted seedlings. Tasks were investigated by analyzing the process and operation time needed to plant 1 containerized seedling using a planting auger and a mattock. The time spent on the various elements of the planting process was measured with a stopwatch but observations were done continuously. Result of the study shows that with the use of a lightweight planting auger the average time spent to plant a containerized seedling is 18.61 seconds while with the use of a mattock it took an average of 26.96 seconds which clearly demonstrates that the planting auger is more efficient in terms of working hours. Working intensity was also analyzed with the use of a portable heart rate monitor (Polar V800). The average increase in heart rate and work intensity index were analyzed for one planting cycle. It was observed that when using the lightweight planting auger, there was a 46.51% increase in the average heart rate while a 74.67% increase in heart rate when the mattock was used which shows that there is a significant increase in heart rate when mattock is used. In addition, work intensity index was observed to be 29.95% and 47.83% when the planting auger and mattock were used respectively. With the continuous use, work intensity index is significantly higher with the use of the mattock as compared to that of the lightweight planting auger. There were no significant differences on the growth increment of seedlings planted using the different tools until a year after planting, however differences in growth increment were observed after a year. A difference of 15.1 cm in height and 3.41 mm in diameter was observed which shows that the use of lightweight planting auger is excellent for planting containerized seedlings.

• Science of Emotion and Sensibility
• /
• v.14 no.4
• /
• pp.531-536
• /
• 2011

The precise measurement of human emotion is of pivotal importance in the field of emotion science. Based on the perspective of psychoneuroimmunoendocrinology, human emotion is now considered to be measurable by body fluid. The biological molecule cortisol, which is known for the stress hormone, has been widely investigated to help researchers to estimate the stress loaded on human body. Until now, several measurement techniques such as High Performance Liquid Chromatography (HPLC), fluorometric assay, and reverse phase chromatography have been developed. However, since these measurements are expensive, take relatively long time for an operation, and they are not portable, they are not appropriate for POCT (point of care testing). In this paper we demonstrate the performance of a miniaturized-microwave resonant device in the measurement of cortisol. Our method has many advantages in that it requires a small volume of sample, has fast response time, is easy to operate and needs no labeling process. Besides, it will shed a light on the measurement techniques for emotion science.

• Science of Emotion and Sensibility
• /
• v.14 no.4
• /
• pp.525-530
• /
• 2011

Emotion is composed of various feelings such as pleasure, sorrow, comfortability, and so on. The complicated process of the measurement has long been recognized as a major hindrance for the studies of emotion. Previously, individuals' emotion has mainly been measured by means of self-report, interview, EEG (electroencephalogram), ECG (electrocardiogram), EOG (electroculography), and body temperature. With thanks to nano/micro technologies, the possibility in the development of emotion-on-a-chip (EOC) has begun to be proposed. EOC will make it possible to analyze one's psychological status by taking a drop of blood. Discovery of emotional biomarkers in body fluids, understanding of the correlation between those biomarkers and the results from brain science are prerequisites to validate the EOC technology. In this paper, paper microfluidics are introduced as a good candidate for the EOC. As paper microfluidics is cost-effective and easy to use it is expected to be a useful device for the emotion measurement. We present the design and fabrication process for the simple paper-based microfluidic device and discuss the possible application in the field of measuring the human emotion.