• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.18 no.3
• /
• pp.261-269
• /
• 2009

Micro end-milling process is applied to fabricate precision mechanical parts cost-effectively. It is a complex and time-consuming job to select optimal process conditions with high productivity and quality. To improve the productivity and quality of precision mechanical parts, micro end-mill wear and cutting force characteristics should be studied carefully. In this paper, high speed machining experiments are studied to construct the optimum process design as well as the mathematical modeling of tool wear and cutting force related to cutting parameters in micro ball end-milling processes. Cutting force and wear characteristics under various cutting conditions are investigated through the condition monitoring system and the design of experiment. In order to construct the cutting database, mathematical models for the flank wear and cutting force gradient are derived from the response surface method. Optimal milling conditions are extracted from the developed experimental models.

• Journal of Powder Materials
• /
• v.6 no.1
• /
• pp.103-110
• /
• 1999

Different sizes of Si powder and milling medium materials (steel and partially stabilized zirconia (PSZ)) were used to synthesize $Ti_3Si$ and $TiSi_2$ by mechanical aollying (MA) of Ti-25.0.at.%Si and Ti-66.7at.% Si powder mixtures. the formation of each titanium silicide did not occur even after 360 min of MA of as-re-ceived Si and Ti powder mixtures due to the lack of homogeneity. $Ti_3Si$, however, was synthesized after 240 min of MA of Ti and 60 min-premilled Si powder mixture. ${\alpha}-TiSi_2$ and $TiSi_2$ were produced by jar milling of Ti and 60 min-premilled Si powder mixture for 48 hr and high -energy PSZ ball-milling in a steel vial for 360 min. The formation of each titanium silicide was characterized by a slow reaction rate as the reactants and product(s) coexisted for a certain period of time. The formation of $Ti_3Si$ and $TiSi_2$ and the reaction rates appeared to be influenced by the Si particle size, the homogeneity of the powder mixtures and the milling medium materials.

• Journal of Powder Materials
• /
• v.16 no.1
• /
• pp.9-15
• /
• 2009

Amorphization and crystallization behaviors of $Ti_{50}Cu_{50}Ni_{20}Al_{10}$ powders during high-energy ball milling and subsequent heat treatment were studied. Full amorphization obtained after milling for 30 h was confirmed by X-ray diffraction and transmission electron microscope. The morphology of powders prepared using different milling times was observed by field-emission scanning electron microscope. The powders developed a fine, layered, homogeneous structure with prolonged milling. The crystallization behavior showed that the glass transition, $T_g$, onset crystallization, $T_x$, and super cooled liquid range ${\Delta}T=T_x-T_g$ were 691,771 and 80 K, respectively. The isothermal transformation kinetics was analyzed by the John-Mehn-Avrami equation. The Avrami exponent was close to 2.5, which corresponds to the transformation process with a diffusion-controlled type at nearly constant nucleation rate. The activation energy of crystallization for the alloy in the isothermal annealing process calculated using an Arrhenius plot was 345 kJ/mol.

• Journal of Powder Materials
• /
• v.25 no.4
• /
• pp.291-295
• /
• 2018

A conductive additive is prepared by dispersing multi-walled carbon nanotubes (MWCNTs) on Cu powder by mechanical milling and is distributed in epoxy to enhance its electrical conductivity. During milling, the MWCNTs are dispersed and partially embedded on the surface of the Cu powder to provide electrically conductive pathways within the epoxy-based composite. The degree of dispersion of the MWCNTs is controlled by varying the milling medium and the milling time. The MWCNTs are found to be more homogeneously dispersed when solvents (particularly, non-polar solvent, i.e., NMP) are used. MWCNTs gradually disperse on the surface of Cu powder because of the plastic deformation of the ductile Cu powder. However, long-time milling is found to destroy the molecular structure of MWCNTs, instead of effectively dispersing the MWCNTs more uniformly. Thus, the epoxy composite film fabricated in this study exhibits a higher electrical conductivity than 1.1 S/cm.

• Resources Recycling
• /
• v.23 no.6
• /
• pp.3-11
• /
• 2014

Bottom ash from coal fired power plants is not widely used due to a broad range of particle sizes and a high carbon content for producing geopolymers. The effect of mechanical activation on compressive strength of bottom ash- based geopolymers was examined by rod and planetary-ball milling to encourage full-fledged recycling of bottom ash, the main component of pond ash. The amount of amorphous component in the milled ash samples did not change significantly after the mechanical activation. It is presumably because needle-shaped mullite crystals, which is a major crystalline phase and grown in a glassy matrix, possess high strength and toughness, and therefore, they could endure external shocks and remain almost intact. Milling operation, however, decreased the particle size and improved the homogeneity of ash, thereby leading to increase reactivity of milled ash with alkali activators. Rod milling produced a relatively narrow particle size distribution of the milled ash particles; however, it was less effective in reducing the particle size. Nevertheless, it was interesting to observe that rod milling had equal effect on improving the compressive strength of geopolymers up to about 37%, as that of planetary ball milling. Rod milling is believed to be suitable process for enhancing the reactivity of bottom ash for large-scale recycling of bottom ash and producing geopolymers.

• Journal of Technologic Dentistry
• /
• v.34 no.2
• /
• pp.113-119
• /
• 2012

Purpose: Zirconia blocks for all ceramic dentures are divided into two groups. One is pre-heated block and the other is binder added block. In this study, the possibility of recycling the remained parts of binder added block after CAD/CAM machining with slip casting process was investigated. Methods: Owing to the binder added block contain large amount of organic matter, Binder burn-out was must be carried out before ball milling for preparing the casting slip. Binder burn-out was accomplished at $600^{\circ}C$ for 10 hours. Ball milling was performed with 5mm zirconia ball and 60mm polyethylene bottle. From 0% to 5% at 1% intervals of alumina was added to zirconia powder for preparing slip. Solid casting was achieved with plaster mold. Cast bodies were dried and sintered at $1,500^{\circ}C$ for 1 hour. Linear shrinkage, apparent porosity, water absorption, bulk density, and flexural strength were tested. Microstructures were observed by SEM, EDS and XRD analysis were executed. Results: Optimum slips for casting was prepared with 300g ball, 100g powder, and 180g distilled water. Cast body without alumina showed 26% of linear shrinkage, 6.07 of apparent density, and 470MPa of three point bend strength. On the other hand, as received zirconia block, which was sintered at the same conditions, showed 23% of linear shrinkage, 6.10 of apparent density, and 680MPa of three point bend strength. When 3% of alumina was added to zirconia, sintered body showed 23% of linear shrinkage, 6.10 of apparent density, and 780MPa of three point bend strength. SEM photomicrographs and EDS analysis showed alumina particles uniformly dispersed in zirconia matrix, and XRD analysis showed no phase transformation of tetragonal zirconia particles was occurred when alumina was added. Conclusion: According to the all of this experimental results, 3% of alumina added cast zirconia body showed excellent mechanical properties more than as received binder containing zirconia block.

• Journal of Powder Materials
• /
• v.20 no.4
• /
• pp.275-279
• /
• 2013

Fe-based oxide dispersion strengthened (ODS) powders were produced by high energy ball milling, followed by spark plasma sintering (SPS) for consolidation. The mixed powders of 84Fe-14Cr-$2Y_2O_3$ (wt%) were mechanically milled for 10 and 90 mins, and then consolidated at different temperatures ($900{\sim}1100^{\circ}C$). Mechanically-Alloyed (MAed) particles were examined by means of cross-sectional images using scanning electron microscopy (SEM). Both mechanical alloying and sintering behavior was investigated by X-ray diffraction (XRD) and high resolution transmission electron microscopy (HR-TEM). To confirm the thermal behavior of $Y_2O_3$, a replica method was applied after the SPS process. From the SEM observation, MAed powders milled for 10 min showed a lamella structure consisting of rich regions of Fe and Cr, while both regions were fully alloyed after 90 min. The results of sintering behavior clearly indicate that as the SPS temperature increased, micro-sized defects decreased and the density of consolidated ODS alloys increased. TEM images revealed that precipitates smaller than 50 nm consisted of $YCrO_3$.

• Journal of the Korean Society of Industry Convergence
• /
• v.4 no.1
• /
• pp.27-34
• /
• 2001

Refining of powder particles and their dissolution into the Al matrix during mechanical alloying(MA) were investigated by using X-ray diffraction(XRD) transmission electron microscopy (TEM) functions of alloy composition, milling time and ball to powder ratio(BPR). It is found that Ti particles less than 20nm are observed in a dark field image of mechanically alloyed Al-10wt%Ti whose XHD pattern exhibits no Ti peak. The observed change of lattice constant of AI indicates that about 1 wt%Ti can he solved in Al after MA for a long time, independent of alloy composition, milling time and BPR, suggesting that most of Ti particles arc retained in the Al matrix. It is concluded that the disappearance of XRD peaks in mechanically alloyed Al-10wt%Ti is not simply attributable to the dissolution of Ti into Al, but associated mainly with extreme refining and/or heavy straining of Ti Particles.

• Journal of the Korean Society of Industry Convergence
• /
• v.4 no.4
• /
• pp.365-369
• /
• 2001

This paper presented a new model of virtualized CNC milling machine. The model verifies the over cut, the under cut and the surface roughness using NC file generated from CAM and cutting condition. The model uses Z-map model to verify workpiece. In this paper, the model used the velocities of x, y and z direction and obtained a center point of a hall end mill for modeling Z-map of workpiece. To investigate the performance of the model, simulation study was carried out. As the results, the model gave geometry accuracy of workpiece, the surface roughness and the chip loads in finish cutting that can predict tool chipping. The virtualized CNC machine can he used a flat end mill, a ball end mill and a rounded end mill.

• Journal of the Korean Ceramic Society
• /
• v.42 no.10 s.281
• /
• pp.685-690
• /
• 2005

Pb(Zr,Ti)$O_{3}$Pb($Mn_{1/3}$$Nb_{2/3}$)$O_{3}$ powder was successfully synthesised by high-energy milling method, and the behavior of low­temperature sintering and piezoelectrical properties of Pb(Zr,Ti)$O_{3}$-Pb($Mn_{1/3}$$Nb_{2/3}$)$O_{3}$ ceramics were investigated as a function of mechanical alloying time. In order to confirm whether the Perovskite phase in this composition was formed by mechanical activation technique or not, we performed X-Ray Diffraction pattern analysis (XRD). The microstructure for the sintered samples were characterized using a Scanning Electronic Microscope (SEM). And the piezoelectrical properties ($k_{p}$ and $Q_{m}$) of the sintered samples was measured using HP 4194A impedance analyzer.