• 대한기계학회논문집A
• /
• 제31권11호
• /
• pp.1077-1082
• /
• 2007

We present a micromechanical active amplifier, inspired from the principle of the outer hair cells in cochlea, amplifying both displacement and force. The present micromechanical active amplifier modulates the resonant carrier motion using the variable stiffness spring whose stiffness changes proportionally to the input motion. We design, fabricate, and characterize two types of the amplifiers A and B, each having the variable stiffness spring fur the maximum displacement gain and force gain, respectively. In the experimental study, the amplifier A shows the displacement gain of 5.62, which is 2.15 times larger than that of the amplifier 3. The amplifier B shows the force gain of 10.0, resulting in 1.26 times larger value compared to that of the amplifier A. We experimentally verify that the haircell-inspired micromechanical amplifiers are capable to amplify both displacement and force.

• 한국유체기계학회 논문집
• /
• 제19권2호
• /
• pp.36-42
• /
• 2016

Mass flow amplifier, which is an aerodynamic device, makes air flow increased by ejecting small amount of compressed air with $Coand{\breve{a}}$ effect. In this study, the flow characteristics of a mass flow amplifier were studied with various flow conditions and geometrical configurations. In order to improve the performance of mass flow amplifier, various values of clearance, diffuser angle and the aspect ratio of induced flow inlet to outlet were considered as design parameter. Furthermore, four different pressure conditions of compressed air were also considered. Numerical study was performed using the commercial CFD code, ANSYS CFX 14.5 with shear stress transport(SST) turbulent model. The results of pressure and velocity distributions were graphically depicted with different geometrical configurations and operating conditions.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2008년도 춘계학술대회 논문집
• /
• pp.801-802
• /
• 2008

• 드라이브 ㆍ 컨트롤
• /
• 제10권4호
• /
• pp.22-28
• /
• 2013

Mechanical and electrical properties of a DDV(Direct Drive servo Valve) with electric feedback are analysed via reverse analysis technique in this work. The DDV is disassembled and mechanical parameters, such as spool mass, spring stiffness and port size are identified. The servo amplifier, which is built in the valve, is reversely analysed and the control scheme and gains for several control actions are also identified. The electrical feedback for spool displacement improves much better the valve performance, such as hysteresis and dynamic bandwidth frequency, than an ordinary mechanical feedback valve. Integrating control action with very large gain was adopted in the valve amplifier, and it seemed to give high performance.

• International Journal of Air-Conditioning and Refrigeration
• /
• 제13권3호
• /
• pp.119-127
• /
• 2005

Liquid pressure amplifiers have been proposed as an energy saving technology for vapor compression refrigeration systems configured with direct-expansion evaporators. The technology utilizes a refrigerant pump in the high pressure liquid line as a means of maintaining a suitable pressure differential across the expansion valve while lowering condensing pressure to achieve the reduction of compressor energy consumption. Applications have been proposed on systems ranging from small unitary air-conditioning to large supermarket and commercial refrigeration systems. This paper clarifies the role of such a device in a vapor compression refrigeration system. Limitations are presented and discussed. Finally, results of detailed analyses are presented to quantify the energy consumption both with and without a liquid pressure amplifier in a unitary air conditioning system. The estimated energy savings associated with the installation of a liquid pressure amplifier are minimal.

• 전기학회논문지
• /
• 제67권3호
• /
• pp.383-390
• /
• 2018

Piezoelectric micro-machined ultrasonic transducers for highly directional speaker need DC bias voltage. Most existing power amplifiers are not suitable for use in highly directional transducers because they are based on AC. In addition, since the piezoelectric micro-machined ultrasonic transducer has a large capacitive reactance, the power efficiency of the power amplifier is very low. Thus this paper proposes a new high efficiency power amplifier with DC bias voltage. In addition, by designing a matching circuit to compensate the capacitive reactance of the micro-machined ultrasonic transducer, the power efficiency of the power amplifier increases. The operating characteristics of the proposed power amplifier was verified by an experimental prototype. The proposed power amplifier is expected to be widely used in designing and implementing other related power amplifiers.

• 전기의세계
• /
• 제18권5호
• /
• pp.12-19
• /
• 1969

The sensitivity of transistorized d.c. amplifiers is mainly limited by drift at operating point caused by ambient temperature changes. A chopper-type transistorized amplifier is necessary to obtain a high sensitivity without recourse to drift compensation which requires the adjustment of several balancing controls. A chopper-stabilized system consisting of an electro-mechanical chopper for input and output and a high-gain a.c. amplifier is designed and analyzed. The gain of the a.c. amplifier, expressed as the ratio of voltages, is larger than 80db in the band of 50C/S - 100KC/S. The complete system gives an open-loop gain of 68db at direct current. The offset voltage is 20.mu.V referred in input and the voltage drift at the input is less than 10.mu.V/hr at 25.deg.C. This type of amplifier would be useful for the high-gain transistorized d.c. amplifier for analog computers. Also, due to the high input impedance, it is suitable for amplification of signals from wide range of source impedances.

• 전기학회논문지
• /
• 제66권8호
• /
• pp.1215-1221
• /
• 2017

Parametric array transducers are used for highly directional speaker in an air environments. Piezoelectric micromachined ultrasonic transducers for parametric array transducers need DC-biased voltage driving signals in order to get high-directional quality-sound features. The existing power amplifier such as class A amplifiers has low efficiency and require large volume heatsinks. To overcome the above-mentioned disadvantages of the conventional amplifier, this paper proposes a new power amplifier system. The proposed power amplifier system ensures high linearity of output characteristic by utilizing the push-pull class B type amplifier. Furthermore, the proposed power amplifier system gets high efficiency because it contains the DC-DC converter-type power supply which can perform energy recovery and envelope tracking function. Also the paper suggests the detailed circuit topology. Its characteristics are verified by the detailed experimental results.

• 한국기계기술학회지
• /
• 제13권3호
• /
• pp.1-6
• /
• 2011

In order to find better performance of heat sink, in this research, different cases were analysed by changing number of slots and shape of fins. Round shape fins which have wide surface showed 24% better heat transfer rate than vertical fins. There were not big discrepancies between 1 slot and 2 slots fins. Consequently, for better performance of heat sink, developments for widening surface and better material for high heat transfer rate are needed.

• 대한기계학회논문집A
• /
• 제31권1호
• /
• pp.62-69
• /
• 2007

Micromanipulator is a device that manipulates an object with high precision. Generally, a parallel-type robot has inherently higher precision than a serial-type robot. In most cases, the use of flexure hinge mechanisms is the most appropriate approach to micromanipulators. The micromanipulator is basically required that have high natural frequency and sufficient workspace. However, previous designs are hard to satisfy the required workspace and natural frequency, simultaneously, because the previous micromanipulators are coupled designs. Therefore, this paper suggests a new design parameter as displacement amplifier and new design procedure based on semi-coupled design in axiomatic design. As a consequence the spatial 3-DOF micromanipulator which is chosen as an exemplary device has natural frequency of 500Hz and workspace of $-0.5^{\circ}{\sim}0.5^{\circ}$. To investigate the effectiveness of the displacement amplifier, simulation and experiment are performed.