• Plant Journal
• /
• v.9 no.1
• /
• pp.50-57
• /
• 2013

This study investigates the risks that can occur during the development stage of IPP project in developing countries. In case that ECA and MLA cannot participate due to poor credit rating of the country, the diversification of power purchaser in marginal states can be a great help to reduce both market risk and country risk at the same time. In case of thermal power plants and combined cycle power plants, the effect of performance degradation as time passed will be considered and expected profit of sponsors should be maintained. Recently, developing countries are expanding IPP projects to reduce the financing cost and Korean power companies are positively participating in IPP projects. Accordingly, the loss of Korean companies should be minimized by risk management through the risk mitigation methods of this study.

• Nuclear Engineering and Technology
• /
• v.43 no.3
• /
• pp.279-286
• /
• 2011

The aging degradation and lifetime assessment of a domestic class 1E Ethylene-Propylene-Diene-Monomer (EPDM), which is a popular insulating elastomer for electrical cables in the nuclear power plants, were studied for equipment qualification verification under the Loss of Coolant Accident (LOCA) conditions. The specimens were acceleratively aged, underwent a LOCA environment, as well as tested mechanically, thermo-gravimetrically, and spectroscopically according to the American Society of the Testing of Materials (ASTM) procedures. The tensile test results revealed that the elongation at break gradually decreased with an increasing aging temperature. The lifetime of EPDM aged isothermally at $140^{\circ}C$ was 1,316 hours and reduced to 1,120 hours after experiencing the severe accident test. The activation energies of the elongation reduction were $1.10{\pm}0.196$ eV and $0.93{\pm}0.191$ eV before and after the LOCA condition, respectively. The TGA test results also showed that the activation energy of the aging decomposition decreased from 1.35 eV to 1.02 eV after undergoing the LOCA environment. Although the mechanical property changes were discernibly observed during the aging process, along with the LOCA simulation, the FT-IR analysis showed that the spectroscopic peaks and their intensities did not alter significantly. Therefore, it can be concluded that the degradation of the domestic class 1E EPDM due to aging can be tolerable, even in severe accident conditions such as LOCA, and thus it qualifies as a suitable insulating material for electrical cables in the nuclear power plants.

• Korean Journal of Optics and Photonics
• /
• v.4 no.4
• /
• pp.420-427
• /
• 1993

Dielectric thin film mirrors are embedded in multimode and single-mode fibers by a fusion splicing technique. The fibers with $45{\circ}$ angled embedded mirrors serve as ultra-compact directional couplers with low excess optical loss of 0.2 dB for multimode and 0.5 dB for single mode at 1.3 ${\mu}m$ and excellent mechanical properties. The reflectance is wavelength dependent and strongly polarization depencient. Far-field scans of the reflected output power measured with a white-light source show a pattern which is almost circularly symmetric with aspect ratio of 1.09 at 5% of the peak power. The splitting ratio in a multimode coupler measured with a diode laser source is much less dependent on input coupling conditions than in conventional fused biconical-taper couplers, indicating that these couplers are less susceptible to modal noise occuring in optical fiber communication systems. Spectral properties of multilayer internal mirrors normal to the fiber axis have been investigated experimentally, and a matrix analysis has been used to explain the results.

• Clean Technology
• /
• v.5 no.2
• /
• pp.45-52
• /
• 1999

Recycling of red mud from the aluminium manufacturing process was investigated to be utilized as plastic fillers. High density polyethylene(HDPE), low density polyethylene(LDPE) and polypropylene(PP) were found to be the suitable plastic material for which red mud can be used as fillers. With the addition of red mud the plastic showed red brown color. As the ratio of amount of red mud to plastic increased, the tensile strength increased while the Izod impact strength decreased. About five percent of ethylene vinyl alcohol(EVA) was needed as an additive to prevent the lowering of impact strength. Maleic anhydride modified polypropylene was effective for reduction of impact strength lowering of PP. Mixed waste plastics containing LDPE, HDPE, PP, polystyrene and ABS could also accommodate red mud as fillers. In this case, significant loss in mechanical properties were observed due to immiscibility between the components. Ethylene propylene rubber(EPR) and styrene butadiene styrene block copolymer (SBS) could be used to improve the impact properties of the commingled waste plastics.

• Clean Technology
• /
• v.12 no.4
• /
• pp.198-204
• /
• 2006

The modification of biodegradable polycaprolactone was accomplished by reactive extrusion with various contents of free radical initiator. Reaction conditions were in the temperature range of $130^{\circ}C$ to $180^{\circ}C$ with initiator contents of 0.1, 0.3, 0.5 and 1.0 wt%. To characterize the modified polycaprolactone (PCL), molecular weight was measured by gel permeation chromatography(GPC) and thermal, mechanical and rheological properties as well as biodegradability were measured. The modified PCL (MPCL) with 1% of initiator showed ca. 20% increase in crystallinity and ca. 50% increase in tensile modulus. Also, a large increase in rheological properties such as complex viscosity, storage and loss modulus was observed. The biodegradability of most MPCL was higher than that of virgin PCL.

• Journal of Welding and Joining
• /
• v.26 no.4
• /
• pp.50-54
• /
• 2008

In this research, anode for SOFC has been manufactured from two different kinds of feedstock materials through thermal spraying process and the properties of the coatings were characterized and compared. One kind of feedstock was manufactured from spray drying method which includes nano-components of NiO, YSZ (300 nm) and graphite. And the other is manufactured by blending the micron size NiO coated graphite, YSZ and graphite powders as feedstock materials. Microstructure, mechanical properties and electrical conductivity of the coatings as-sprayed, after oxidation and after hydrogen reduction containing nano composite which is prepared from spray-dried powders were evaluated and compared with the same properties of the coatings prepared from blended powder feedstock. The coatings prepared from the spray dried powders has better properties as they provide larger triple phase boundaries for hydrogen oxidation reaction and is expected to have lower polarization loss for SOFC anode applications than that of the coatings prepared from blended feedstock. A maximum electrical conductivity of 651 S/cm at $800^{\circ}C$ was achieved for the coatings from spray dried powders which much more than that of the average value.

• Korean Journal of Medicinal Crop Science
• /
• v.7 no.1
• /
• pp.27-30
• /
• 1999

This experiment was carried out to determine the adequate machine peeling and retting time of peony roots, which are used as medicinal resources in Korea. When the roots were peeled for $10{\sim}30$ minitues in the peeling machine, the epidermis of root was removed, and higher yield was obtained and paeoniflorin content as compared with roots which were peeled for longer time. The paeoniflorin content of root varied with the different parts of root. The highest content was recorded in the upper part and the lowest in the middle part. The loss of paeoniflorin increased in the roots processed for expanded peeling and retting time. Lightness of peeled root was higher and ${\Delta}\;E$ was lower in the roots which were peeled by machine for longer time.

• Journal of Power Electronics
• /
• v.16 no.6
• /
• pp.2119-2128
• /
• 2016

Due to detection and control errors, some high-frequency harmonics with voltage-source characteristics cause circulating currents in modular inverters. Moreover, the circulating currents are usually affected by the output filters (OF) of each module due to their filter and resonance properties. The interaction among the circulating currents in the modules increase the power loss and reduce system stability and control precision. Therefore, this paper reports the results of a study on the SPWM high-frequency harmonics circulating currents for a double-module VSI. In the paper, an analysis of the circulating-current circuits is briefly described. Next, a mathematic model of the single-module output voltage based on the carrier frequency of SPWM is built. On this basis, through mathematic modeling of high-frequency harmonic circulating currents, the formation mechanism and distribution characteristics of circular currents and their influences are studied in detail. Finally, the influences of the OF on the circulating currents are studied by mainly taking an LC-type filter as an example. A theoretical analysis and experimental results demonstrate some important characteristics. First, the carrier phase shifting of the SPWM for each module is the major cause of the SPWM harmonic circulating currents, and the circulating currents are in an odd distribution around n-times the carrier frequency $n{\omega}_s$, where n = 1, 2, 3, ${\ldots}$. Second, the harmonic circular currents do not flow into the parallel system. Third, the OF can effectively suppress the non-circulating part of the high-frequency harmonic currents but is ineffective for the circulation part, and actually reduces system stability.

• Journal of Powder Materials
• /
• v.18 no.5
• /
• pp.449-455
• /
• 2011

In this study, p-type $(AgSbTe_2)_{15}(GeTe)_{85}$: TAGS-85 compound powders were prepared by gas atomization process, and then their microstructures and mechanical properties were investigated. The fabricated powders were of spherical shape, had clean surface, and illustrated fine microstructure and homogeneous $AgSbTe_2$ + GeTe solid solution. Powder X-ray diffraction results revealed that the crystal structure of the TAGS-85 sample was single rhombohedral GeTe phase, which with a space group $R_{3m}$. The grain size of the powder particles increased while the micro Vickers hardness decreased with increasing annealing temperature within the range of 573 K and 723 K due to grain growth and loss of Te. In addition, the crystal structure of the powder went through a phase transformation from rhombohedral ($R_{3m}$) at low-temperature to cubic ($F_{m-3m}$) at high-temperature with increasing annealing temperature. The micro Vickers hardness of the as-atomized powder was around 165 Hv, while it decreased gradually to 130 Hv after annealing at 673K, which is still higher than most other fabrication processes.

• Proceedings of the International Microelectronics And Packaging Society Conference
• /
• 2001.04a
• /
• pp.35-43
• /
• 2001

Flip chip assembly on organic substrates using ACAs have received much attentions due to many advantages such as easier processing, good electrical performance, lower cost, and low temperature processing compatible with organic substrates. ACAs are generally composed of epoxy polymer resin and small amount of conductive fillers (less than 10 wt.%). As a result, ACAs have almost the same CTE values as an epoxy material itself which are higher than conventional underfill materials which contains lots of fillers. Therefore, it is necessary to lower the CTE value of ACAs to obtain more reliable flip chip assembly on organic substrates using ACAs. To modify the ACA composite materials with some amount of conductive fillers, non-conductive fillers were incorporated into ACAs. In this paper, we investigated the effect of fillers on the thermo-mechanical properties of modified ACA composite materials and the reliability of flip chip assembly on organic substrates using modified ACA composite materials. Contact resistance changes were measured during reliability tests such as thermal cycling, high humidity and temperature, and high temperature at dry condition. It was observed that reliability results were significantly affected by CTEs of ACA materials especially at the thermal cycling test. Results showed that flip chip assembly using modified ACA composites with lower CTEs and higher modulus by loading non-conducting fillers exhibited better contact resistance behavior than conventional ACAs without non-conducting fillers. Microwave model and high-frequency measurement of the ACF flip-chip interconnection was investigated using a microwave network analysis. ACF flip chip interconnection has only below 0.1nH, and very stable up to 13 GHz. Over the 13 GHz, there was significant loss because of epoxy capacitance of ACF. However, the addition of $SiO_2filler$ to the ACF lowered the dielectric constant of the ACF materials resulting in an increase of resonance frequency up to 15 GHz. Our results indicate that the electrical performance of ACF combined with electroless Wi/Au bump interconnection is comparable to that of solder joint.