• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1998년도 추계학술대회 논문집 학회본부A
• /
• pp.25-27
• /
• 1998

In this paper electromagnetic force and its distribution are analyzed on the nonlinear magnetic materials by Finite Element Method. Most of magnetic materials have the nonlinear characteristic, which considerably effects on the magnetic system. And it is necessary to know its distribution at the every Part of the magnetic material in order to design the, magnetic system considering noise, vibration and strain characteristic. The results are obtained by Maxwell stress. virtual work and magnetic charge method and compared with one another.

• Journal of the Korean Society for Industrial and Applied Mathematics
• /
• 제16권3호
• /
• pp.181-192
• /
• 2012

Here in this paper, the steady paint film flow on a vertical wall of a non-Newtonian pseudo plastic fluid for drainage problem has been investigated. The exact solution of the nonlinear problem is obtained for the velocity profile. Also the average velocity, volume flux, shear stress on the wall, force to hold the wall in position and normal stress difference have been derived. We retrieve Newtonian case, when material constant ${\mu}_1$ and relaxation time ${\lambda}_1$ equal zero. The results for co-rotational Maxwell fluid is also obtained by taking material constant ${\mu}_1$ = 0. The effect of the zero shear viscosity ${\eta}_0$, the material constant ${\mu}_1$, the relaxation time ${\lambda}_1$ and gravitational force on the velocity profile for drainage problem are discussed and plotted.

• 농업과학연구
• /
• 제13권2호
• /
• pp.255-264
• /
• 1986

수확시기(收穫時期)의 벼줄기에 대(對)한 역학적(力學的), 점탄성적(粘彈性的) 특성(特性)을 구명(究明)하기 위(爲)해 압축시(壓縮時) 최대압축하중(最大壓縮荷重), 이력현상(履歷現象), 가공경화현상(加工硬化現象) 및 점탄성(粘彈性) 거동(粘彈性)에 대(對)한 변형속도(變形速度), 초기하중(初期荷重)이 영향을 분석(分析)하며, 도해법(圖解法) 및 computer에 의(依)한 수치해법(數値解法)으로 하중이완(荷重弛緩)의 rheological model 을 제시(提示)코져 시험(試驗)한 결과(結果)는 다음과 같다. 1. 압축시험시(壓縮試驗時) 벼줄기의 최대압축하중(最大壓縮荷重)은 다수계(多收系) 품종(品種)보다 일반계(一般系)에서 큰 경향(傾向)이었다. 2. 동진벼의 부위별(部位別) 최대압축하중(最大壓縮荷重)은 4절간이 가장 컷고, 3절간, 1절간 하부(下部), 2절간, 1절간 상부(上部)의 순(順)으로 작았다. 3. 비례한도내(比例限度內)의 하중(荷重)으로 loading-unloading 할 때 일부의 잔유변형이 발생(發生)하여 탄소성(彈塑性) 변형(變形)을 일으켜 이력손실(履歷損失)을 가져왔다. 4. Loading-unloading cycle을 반부(反復)하면 소성변형(塑性變形)이 감소(減少)하여 가공경화현상(加工硬化現象)을 보였다. 5. 하중이완거동(荷重弛緩擧動)은 변형속도(變形速度)의 증가(增加)에 따라 이완속도(弛緩速度)가 빨라졌다. 6. Computer에 의(依)한 수치해법(數値解法)과 도해법(圖解法)으로 이완거동(弛緩擧動)을 분석(分析)한 결과(結果) 3개지수항(個指數項)으로 표시(表示)되고 일반화(一般化) Maxwell model로 나타내었다. 이 model의 rheology 방정식(方程式)은 다음과 같다. $$F(t)=C_1e^{{-t/{\tau}}_1}+C_2e^{{-t/{\tau}}_2}+C_3e^{{-t/{\tau}}_3}$$ 동진벼줄기의 함수율(含水率) 71.9%(w.b.), 초기하중(初期荷重) 45.5 N, 변형속도(變形速度) 38mm/min 일 때 하중이완(荷重弛緩) 방정식(方程式)은 다음과 같았다. $$F(t)=24.3e^{-t/1006}+7.6e^{-t/12.7}+13.6e^{-t/1.8}$$ 7. 초기변형(初期變形)이 클수록 하중이완(荷重弛緩)은 크게 일어났다.

• 한국가시화정보학회:학술대회논문집
• /
• 한국가시화정보학회 2007년도 추계학술대회
• /
• pp.128-133
• /
• 2007

An electrostatic inkjet head can be used for manufacturing processes of large display systems and printed circuit boards (PCB) as well as inkjet printers because an electrostatic field provides an external force which can be manipulated to control sizes of droplets. The existing printing methods such as thermal bubble and piezo inkjet heads have shown difficulties to control the ejection of the droplets for printing applications. Thus, the new inkjet head has been proposed using the electrostatic force. A numerical analysis has been performed to calculate the intensity of the electrostatic field using the Maxwell's equation. Also, experiments have been carried out to investigate the droplet movement using a downward capillary with outside diameter of $500{\mu}m$. Gravity, surface tension, and electrostatic force have been analyzed with high voltages for a drop-on-demand ejection. It has been observed that the droplet size decreases and the frequency of the droplet formation and the velocity of the droplet ejection increase with increasing the intensity of the electrostatic field using high-speed camera.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2007년도 추계학술대회 논문집
• /
• pp.1605-1609
• /
• 2007

In the case of Linear induction motor(LIM), numerical analysis method like Finite Element Method(FEM) has been mainly used to analyze the travelling magnetic field problem which includes the velocity-induced electromotive force. If the problem including the velocity-induced electromotive force is analyzed by FEM using Galerkin method, the solution can be oscillated according to Peclet Number, which is determined by conductivity, permeability, moving velocity and size of mesh. Consequently, the accuracy of the solution can be low and the Loops of flux can be occurred at the secondary back-iron. These loops of flux occurred at the secondary back-iron does not exist physically, but it can be occurred in the analysis. In this case, the loops of flux can be generally removed by using Up-Wind method which is impossible to apply a conventional S/W tool(Maxwell 2D). Therefore, in this paper, authors examined the Loops of flux occurred at the secondary back-iron of LIM according to variations of Peclet Number, and analyzed whether these loops of flux affect on the thrust force characteristics of LIM or not.

• Journal of international Conference on Electrical Machines and Systems
• /
• 제3권3호
• /
• pp.317-324
• /
• 2014

The forces involved in the firing of the electromagnetic rail gun may be analyzed from Amperian, Maxwellian and Einsteinian approaches. This paper discusses these different paradigms with regard to rail gun performance modeling relating to the generation and balance of the forces caused by the currents and their induced magnetic fields. Recent experimental work on model rail guns, where the armature is held static, shows very little recoil upon the rails, thereby indicating a possible violation of Newton's Third Law of Motion. Dynamic testing to show this violation, as suggested by the authors in an earlier paper, has inherent technical difficulties. A purpose-built finite element C/C++ simulator that models that suspended rail gun firing action shows a net force acting upon the entire rail gun system. A new effect in physics, universal in scope, is thus indicated: a current circulating in an asymmetric and rigid circuit causes a net force to act upon the circuit for the duration of the current. This conclusion following from computer simulation based upon Maxwellian electrodynamics as opposed to the more modern relativistic quantum electrodynamics needs to be supported by unambiguous experimental validation.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 하계학술대회 논문집 Vol.4 No.1
• /
• pp.227-232
• /
• 2003

Usually, the thrust of a Linear Pulse Motor(LPM) is calculated by magnetic equivalent circuit modelling method. Analytical thrust deviation exists to calculating magnetic flux density by using Permeance Modelling Method, Finite Element Method, and Velocity Electric Motive Force Method. For calculating accuracy thrust by using these every method, the thrust is calculated and compared by Lorentz Force Method, Magnetic Coenergy Method, and Maxwell correspondence force Method. And that becomes important factor at the comparison of each capacity and parameter of motor. So this study wants to compare and analyze measurement data and calculating data of the static thrust of LPM. and then we can get more accuracy method, calculating the static thrust of LPM.

• Journal of Electrical Engineering and Technology
• /
• 제7권2호
• /
• pp.184-192
• /
• 2012

The torque and unbalanced magnetic forces in permanent magnet machines are resultants of the tangential, axial and normal magnetic forces, respectively. Those are in general influenced by pole-teeth-winding configuration. A study of the torque and unbalanced magnetic forces of a small flux concentrating permanent magnet transverse flux machine (FCPM-TFM) in segmented compact structure is presented in this paper. By using FLUX3D software from Cedrat, Maxwell stress tensor has been solved. Finite element (FE-) magneto static study followed by transient analysis has been conducted to investigate the influence of unsymmetrical winding pattern, in respect to the rotor, on the performance of the FCPM-TFM. Calculating the magnetic field components in the air gap has required an introduction of a 2D grid in the middle of the air gap, whereby good estimations of the forces are obtained. In this machine, the axial magnetic forces reveal relatively higher amplitudes compared to the normal forces. Practical results of a prototype motor are demonstrated through the analysis.

• Structural Engineering and Mechanics
• /
• 제11권1호
• /
• pp.71-87
• /
• 2001

A frequency domain response analysis is presented for building frames passively controlled by viscoelastic dampers, under harmonic ground excitation. Three different models are used to represent the linear dynamic force-deformation characteristics of viscoelastic dampers namely, Kelvin model, Linear hysteretic model and Maxwell model. The frequency domain solution is obtained by (i) an iterative pseudo-force method, which uses undamped mode shapes and frequencies of the system, (ii) an approximate modal strain energy method, which uses an equivalent modal damping of the system in each mode of vibration, and (iii) an exact method which uses complex frequency response function of the system. The responses obtained by three different methods are compared for different combinations of viscoelastic dampers giving rise to both classically and non-classically damped cases. In addition, the effect of the modelling of viscoelastic dampers on the response is investigated for a certain frequency range of interest. The results of the study are useful in appropriate modelling of viscoelastic dampers and in understanding the implication of using modal analysis procedure for building frames which are passively controlled by viscoelastic dampers against base excitation.

• 대한화학회지
• /
• 제21권5호
• /
• pp.330-338
• /
• 1977

고체의 소성변형을 설명하기 위하여 다음과 같은 가정을 하였다. (1) 고체의 소성변형은 크게 두 가지 기구 즉 dislocation 운동과 grain boundary 운동에 의하여 일어난다. (2) Dislocation 운동에 있어서 유동 단위들은 역학적 모형으로 나타내면 다종의 Maxwell 단위들의 평행연결형으로 되고 grain boundary 유동단위들도 다종의 Maxwell 단위들의 평행연결로 표현된다. 이를 물리적으로 설명하면 같은 부류의 유동단위들은 모두 같은 shear plane에서 같은 shear rate로 흐름을 의미한다. (3) Grain boundary 유동단위들과 dislocation 유동단위들 같은 서로 직렬 연결되어 있다. 이는 물리적으로 고체내에서 stress는 균일하게 작용하나 shear rate는 shear plane 의 종류(dislocation 운동면과 grain boundary 운동면)에 따라 달리 나타남을 의미한다. (4) Dislocation 유동단위들과 grain boundary 운동단위들의 운동은 그들의 흐름을 방해하는 장애물 근방의 원자 또는 분자들이 확산해 나가므로써 가능하게 된다. 이러한 가정하에 반응속도론을 적용하여 shear rate와 shear stress를 구하는 일반식을 도출하였다. 본 연구에서는 실제로 중요한 네가지 경우에 대하여 상기 도출한 일반식을 고찰하였다.