• 한국기계가공학회지
• /
• 제14권5호
• /
• pp.81-87
• /
• 2015

In this paper, the finite element method was used for the flow and strength analysis of aluminum alloy under friction stir welding. The simulations were carried out using Sysweld s/w, and the modeling of the sheet was executed using Unigraphics NX6 s/w. The welding variables for the analysis were the shoulder diameter, rotating speed, and welding speed of the tool. Additionally, a three-way factorial design method was applied to confirm the effect of the welding variables on the flow and strength analysis with variance analysis. From these results, the rotating speed had the greatest influence on the maximum temperature, and the maximum temperature was $578.84{\pm}12.72$ at a confidence interval of 99%. The greater the rotating speed and shoulder diameter, the greater the difference between maximum and minimum temperature. Furthermore, the shoulder diameter had the largest influence on von Mises stress, and the von Mises stress was $184.54{\pm}12.62$ at a confidence interval of 99%. In addition to the increased shoulder diameter, welding speed, and rotating speed of the tool increased the von Mises stress.

• 한국해양공학회지
• /
• 제23권4호
• /
• pp.47-51
• /
• 2009

Thrust is one of the important performance characteristics of an AUV. At the design stage, the resistance of an AUV at its maximum speed is estimated and then the thrust system is designed, including the propeller diameter, propeller rpm, driving system, and required power. However, it is not possible to be certain that the thrust system has been correctly designed until the AUV is launched and its speed is measured. If data from a propeller open-water test is available, the thrust and torque of the propeller at a certain speed can be estimated. In addition, if the motor's torque characteristics are available, the maximum speed saturated by the induced propeller torque can be estimated. In this paper, an easy technique for estimating the maximum speed of an AUV will be shown, even in a case where additional resistance is gained from appendages not considered at the design stage. Furthermore, the thrust performance changes by adjusting the diameter of the propeller can be easily investigated.

• 한국조명전기설비학회:학술대회논문집
• /
• 한국조명전기설비학회 2009년도 추계학술대회 논문집
• /
• pp.363-366
• /
• 2009

The maximum output torque developed by the machine is dependent on the allowable current rating and maximum voltage that the inverter can supply to the machine. Therefore, to use the inverter capacity fully, it is desirable to use the control scheme considering the voltage and current limit condition, which can yield the maximum torque per ampere over the entire speed range. This controller is controlled speed and current using hybrid PI(HBPI) controller and estimation of speed using ANN. Also, this paper is proposed control of maximum torque per ampere(MTPA) of induction motor. This strategy is proposed which is simple in structure and has the honest goal of minimizing the stator current magnitude for given load torque. The performance of the proposed induction motor drive with maximum torque control using HBPI controller is verified by analysis results at dynamic operation conditions.

• 한국운동역학회지
• /
• 제15권2호
• /
• pp.93-102
• /
• 2005

The purpose of this study was to examine the effect of step length on the joint moment. The subjects were 4 undergraduate and graduate students in their 20s with normal legs. The subjects were individually tested by the running timer at the walking speed of 0.67m/s, 134m/s, and 2.46m/s. The step length was regulated to -10% of normal, normal and +10% of normal step length using foot print. The walking performances of each subjects were filmed using a high speed video camera. The raw data were analyzed by LabVIEW Graphical Program and these data were analyzed by ANOVAs and Scheffe. The results of this study were as follows: The maximum dorsiflexion moment of the ankle joint increased as the step length increased only at the fast walking speed. Although there wasn't significant difference shown in the plantar flexion moment, regular pattern in the plantar flexion moment which increased as the step length increased was found. The first maximum extension moment of the knee joint increased only at the normal walking speed, but there appeared no significant difference in the maximum flexion and second extension moment. The maximum extension moment of the hip joint increased at the normal and fast walking speed. Although there wasn't significant difference, regular pattern in flexion moment which increased as the step length increased was found.

• Wind and Structures
• /
• 제26권3호
• /
• pp.129-146
• /
• 2018

Extreme wind speed analysis has been carried out conventionally by assuming the extreme series data is stationary. However, time-varying trends of the extreme wind speed series could be detected at many surface meteorological stations in China. Two main reasons, exposure change and climate change, were provided to explain the temporal trends of daily maximum wind speed and annual maximum wind speed series data, recorded at Hangzhou (China) meteorological station. After making a correction on wind speed series for time varying exposure, it is necessary to perform non-stationary statistical modeling on the corrected extreme wind speed data series in addition to the classical extreme value analysis. The generalized extreme value (GEV) distribution with time-dependent location and scale parameters was selected as a non-stationary model to describe the corrected extreme wind speed series. The obtained non-stationary extreme value models were then used to estimate the non-stationary extreme wind speed quantiles with various mean recurrence intervals (MRIs) considering changing climate, and compared to the corresponding stationary ones with various MRIs for the Hangzhou area in China. The results indicate that the non-stationary property or dependence of extreme wind speed data should be carefully evaluated and reflected in the determination of design wind speeds.

• 한국지능시스템학회논문지
• /
• 제25권4호
• /
• pp.327-333
• /
• 2015

풍력 터빈은 정격 풍속 미만일 때는 최대 출력을 내기위한 제어를 한다. MPC(Maximun Power Control)제어방법은 발전기의 회전속도를 제어하여 최대 출력을 내는 방법인데 풍속을 알아야한다. 하지만 여러 가지 이유로 풍속을 실측하기보다는 풍속을 예측하여 사용하는 방법들이 제안되고 있다. 풍속예측은 TSR(Tip Speed Ratio)을 알아야 하는 데, TSR은 복잡한 관계식을 풀어야 한다. 그래서 TSR을 구하기 위해 다양한 방법들이 소개되고 있다. 본 논문에서는 TSR을 쉽고 빠르게 구하기 위하여 복잡한 관계식을 리그레션을 이용하여 간단한 방정식으로 근사화하는 방법을 제안하였다. 제안된 방법은 Matlab/Simulink 시뮬레이션을 통하여 제대로 작동하는 것을 확인하였다.

• Tribology and Lubricants
• /
• 제17권4호
• /
• pp.297-306
• /
• 2001

Under the condition of variable density and specific heat, maximum pressure, maximum temperature, bearing load, friction and side leakage in high-speed journal bearing operation are examined within some degree of Journal misalignment. The results are compared with the calculation results under the conditions of constant density and specific heat, and variable density and constant specific heat. It is found that the condition of variable density and specific heat play important roles in determining friction and load of Journal bearing at high speed operation.

• 한국산학기술학회논문지
• /
• 제17권4호
• /
• pp.92-99
• /
• 2016

풍력터빈은 정격풍속미만에서 최대출력을 내기위한 제어를 한다. 최대출력을 얻기 위한 방법 중에는 최적 TSR(Tip Speed Ratio)제어와 P&O(Perturbation and Observation) 제어가 대표적이라 할 수 있다. P&O 제어는 출력과 회전속도만을 이용하여 간단한 알고리즘으로 제어되지만 반응속도가 느린 것이 단점이라 할 수 있다. 최적 TSR 제어는 반응속도가 빠르지만 정확한 풍속을 알아야만 된다. 정확한 풍속을 구하기 위하여 측정을 하거나 예측하는 방법을 사용한다. 풍속을 측정하기 위하여 풍속계를 풍력터빈에 가까이 설치하게 되는 데, 이 때 블레이드의 간섭으로 정확한 풍속 측정이 쉽지 않다. 그래서 풍속을 예측하는 방법들이 사용하게 되었다. 풍속을 예측하기 위하여 신경망을 비롯한 다양한 수치해석 방법들이 사용되고 있으나 풍속예측 문제는 역문제와 관련이 있어 그리 간단치가 않다. 본 논문에서는 기존의 방법들과 다르게 역문제로 풀지 않고 바람의 출력그래프에서 터빈의 출력과 회전속도만을 이용하여 풍속을 예측할 수 있는 새로운 방법을 제안하였다. Matlab/Simulink을 사용하여 제안된 방법으로 풍속이 제대로 예측되며 최대 출력제어가 되는 것을 확인하였다.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2011년도 추계학술대회
• /
• pp.285-286
• /
• 2011

Maximum Power Point Tracker (MPPT) is the big issue in generating power based on Wind Energy Conversion System. In case of unknown turbine characteristic, it is useful to implement MPPT based on fuzzy logic control. This kind of control is able to find the value of duty cycle to meet maximum power point at particular wind speed. There are many methods to develop MPPT based fuzzy logic controls. In this paper, two of the methods are compared both at low and high fluctuating wind speed.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2011년도 정기총회 및 추계학술대회 논문집
• /
• pp.1497-1502
• /
• 2011

Increasing tensions of contact wire and messenger wire are essential to construct a test-bed for catenary system in the 400km/h speed on Honam high-speed railway. Because heavy load is applied to a mast due to the increased the tensions of both wires it is required to investigate the strength of the foundation. Therefore, in this study the maximum moment of an electric pole under the worst condition was calculated to investigate the strength of the pole foundation on the bridges. The maximum moment database table used in the construction of Kyungbu high-speed railway was referenced to derive the worst conditions and to review the composition of catenary system in the test-bed section. From the results of this study regarding assumptions and calculation process it will be possible to estimate the optimized strength of the pole foundations on the bridges which will be constructed in the future.