• 대한기계학회논문집A
• /
• 제31권10호
• /
• pp.981-985
• /
• 2007

We present a MEMS-based portable Direct Methanol Fuel Cell (micro-DFMC), featured by a platinum sputtered microcolumn electrode and a built-in fuel chamber containing a limited amount of methanol fuel. Also presented is a micro-DMFC stack structure having a common electrolyte sandwiched by the microcolumn electrodes. The single cells with ME16 and PE16 electrodes show the maximum power densities of $31.04{\pm}0.29{\mu}W/cm^2$ and $9.75{\pm}0.29{\mu}W/cm^2$, respectively; thus indicating the microcolumn electrode (ME16) generates the power density (3.2 times) higher than the planar electrode (PE16). The single cell tests of ME16 and ME4 electrodes (Fig.8) show the maximum power of $31.04{\pm}0.29{\mu}W/cm^2$, and $25.23{\pm}2.7{\mu}W/cm^2$, respectively; thus demonstrating the increased window frame reduces the normalized standard power deviation (standard deviation over the average power). The normalized deviation of 0.11 in ME4 cell has been reduced to 0.01 in ME16 cell due to the increased window frames. The maximum power density of 4-cell stack is 15.7 times higher than that of the single cell. 4-cell stack produces the power capacity of 20.3mWh/g during 980min operation at the voltage of 450mV with the load resistance of $800{\Omega}$.

• 조명전기설비학회논문지
• /
• 제23권6호
• /
• pp.85-88
• /
• 2009

업무용 건축물 분야에서의 초에너지절약형 시스템으로의 개선이 절실하다. 사무소용/병원/호텔 건물을 중심으로 시간대별 및 연간 전력사용량 등의 전력소비 특성을 조사하였고, 건물연면적, 계약전력, 최대수요진력 등을 조사 분석하였다. 조사된 자료의 전체 특징과 중심적인 경향을 알아 보기 위해서 평균값, 표준편차, 최대값, 최소값, 부하율 등의 특징파라메터를 분석하였다 이를 토대로 연간 전기에너지 사용 총량과 에너지절약 성능의 관리기준을 나타내는 전력원단위를 분석하였고, 전기에너지 연간 사용총량 산정에 필요한 자료를 데이터베이스화하였다.

• 대한전기학회논문지:전력기술부문A
• /
• 제53권1호
• /
• pp.38-42
• /
• 2004

In this paper we analyzed the electromagnetic behavior of a superconducting fault current limiter (SFCL) under the quench state using FEM. The analysis model used in this work is 5.5 KVA meander-line type SFCLs which are currently developed by Superconductor Power System Lab in Korea Electric Power Research Institute. Meshes of 3,650 triangular elements were used in the analysis of this SFCL. Analysis results showed that the distribution of current density was concentrated to inner curved line in meander-line type SFCL and the maximum current density was 14.61 A/$m^2$ and also the maximum Joule heat was 2,030 W/$m^2$ in this region. We think that the new and the modified structure must be considered for an uniform distribution of the electromagnetic field.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2008년도 추계학술대회 논문집
• /
• pp.59-62
• /
• 2008

The performance behavior of solid oxide fuel cell using reformate gas as fuels was investigated. When the pre-reformate gas was used without steam, the maximum power density was 50% lower than that using H2. This may be due to carbon deposition caused by the pyrolysis of remaining hydrocarbons. However, when the steam was added, the maximum power density showed a relatively small variation according to reformate gas. When pre-reformate gas with steam was fed into anode, the SOFC showed the stable performance without sharp voltage drop during 10h operation.

• 한국조명전기설비학회:학술대회논문집
• /
• 한국조명전기설비학회 2006년도 춘계학술대회 논문집
• /
• pp.254-259
• /
• 2006

It is increased electrical energy consumption with the development of intelligence society in the subway station and thus an energy conservation through efficient use of electricity became more important. This paper shows a reasonable design load density in subway stations, that was made by the systematic and statistical way considering actual conditions, such as investigated electric equipment capacity, peak power consumption, demand factor, etc., for 34 subway stations and 10 electrical design offices. In this dissertation, it is necessary to analyse the key features and general trend from the investigated data. It made an analysis of the feature parameters, such as average, standard deviation, median, maximum, maximum and thus it was carried linear and nonlinear regression analysis.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2007년도 추계학술대회 논문집
• /
• pp.151-153
• /
• 2007

Recently study on components for a electric golf car and a utility car driven by a electric motor has been performed actively, and the study on a drive motor, a inverter and a battery focuses on a small, light weight and high power density source to improve fuel efficiency using limited electric energy. Especially, since a utility car such as a golf car performance depends on initial acceleration and maximum speed capability, a drive system requires high power and large and wide operation area, This study therefore investigates on the interior permanent magnet synchronous motor with high power density and wide operation, and is verified with the test result after design and characteristic analysis is performed.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 춘계학술대회 논문집
• /
• pp.998-1002
• /
• 1997

This study has been performed to predict beam absorption with analysis of temperature field by using a FEM in co /sab 2/ laser hardening and to invesrigate into some effects of power density and travel speed of laser beam on the microstructure and hardness of ductile cast iron treated by laser surface hardening technique. Optical micrograph has shown that large martensite and small amount of retained austenite appear in inside hardened zone. Hardness measurement has revealed that the range of maximum hardness value is Hv=415 .+-. 10. The power density increases and the travel speed decreases, the depth of hardened zone increases due to increase of input power density.

• 한국분말재료학회지
• /
• 제8권4호
• /
• pp.239-244
• /
• 2001

To investigate the effect of process parameters on selective laser sintering of Cu/polyamide mixed powder, Cu/polyamide mixed powder was sintered by selective laser with changing laser power and scanning speed. The properties of sintered body were evaluated by measuring the density and tensile strength, and analysis of XRD, FT-Raman and microstructure. With an increase in the laser power, the density and ultimate tensile strength of sintered Cu/polyamide body increase and then decrease. The maximum values of the density and ultimate tensile strength were decreased with increasing laser scanning speed. These changes were concerned with the difference of irradiation energy of laser into the powder layer. It was considered that the change of the mechanical property of the sintered body with irradiation energy of laser is due to the changes of amount of copper particle and property of polyamide.

• Environmental Engineering Research
• /
• 제23권4호
• /
• pp.383-389
• /
• 2018

Microbial fuel cell (MFC) is an innovative environmental and energy system that converts organic wastewater into electrical energy. For practical implementation of MFC as a wastewater treatment process, a number of limitations need to be overcome. Improving cathodic performance is one of major challenges, and introduction of a current collector can be an easy and practical solution. In this study, three types of current collectors made of stainless steel (SS) were tested in a single-chamber cubic MFC. The three current collectors had different contact areas to the cathode (P $1.0cm^2$; PC $4.3cm^2$; PM $6.5cm^2$) and increasing the contacting area enhanced the power and current generations and coulombic and energy recoveries by mainly decreasing cathodic charge transfer impedance. Application of the SS mesh to the cathode (PM) improved maximum power density, optimum current density and maximum current density by 8.8%, 3.6% and 6.7%, respectively, comparing with P of no SS mesh. The SS mesh decreased cathodic polarization resistance by up to 16%, and cathodic charge transfer impedance by up to 39%, possibly because the SS mesh enhanced electron transport and oxygen reduction reaction. However, application of the SS mesh had little effect on ohmic impedance.

• Nuclear Engineering and Technology
• /
• 제16권4호
• /
• pp.181-194
• /
• 1984

변분법을 사용하여 원자로의 핵연료 관리문제를 연구하였다. 원자력 발전소에 영향을 미치는 두 함수 즉 이윤함수와 가격함수는 원자로의 연소도방정식과 최대허용출력 밀도에 대한 부등 제약조건이며, 이들은 임계성의 제약조건이 된다. 초기이윤의 변분해는 원자로에 뚜렷한 두 영역이 있음을 보여 주었다. 즉 일정 출력 영역과 최소 재고량 또는 평활 중성자속 영역이 그것이다. 이들 든 영역의 변이점은 전력에 대한 이윤과 연료에 대한 이자 지급에 상당히 중요하다. 그러므로 각 영역에서 동일 농축도의 핵연료를 가질 동일 부피의 세 영역으로 된 원자로를 최적화 하기 위하여 핵연료 주기 가격 함수가 사용 되었다. 최대 허용 출력 밀도에 대한 부등 제약조건들은 이들 부등 제약 조건이 원자로심의 어느 특정 점이나 로심주기를 통하여 항상 동일 제약조건이 되어야 한다. 원자로의 임계성과 출력밀도에 대한 동일 제약조건에 관계된 핵연료의 연소도에 대한 계차 방정식의 해를 구하였으며 최적 농축도의 위치를 구하기-위하여 구배법을 사용하였다. 이들 계산결과는 부동 제약 조건들을 적절히 적용하면 원자로를 최적화하기 위하여 비선형 최적 기술이 사용될 수 있음을 보여 주었다.