• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.23 no.2
• /
• pp.143-147
• /
• 2010

We have fabricated simple triple-layer blue-emitting phosphorescent organic light emitting diodes (OLEDs) using different thicknesses of N,N'-dicarbazolyl-3,5-benzene (mCP) host layers doped with bis[(4,6-di-fluorophenyl)-pyridinate-N,$C^{2'}$]picolmate (FIrpic) guest materials. The thicknesses of mCP:FIrpic layers were 5, 10, and 30 nm. Driving voltage, current and power efficiencies were investigated. The current efficiency was higher in the 10 nm thick mCP:FIrpic device, resulting from the better electron-hole balance. The device with 10 nm mCP:FIrpic layer exhibited the maximum current efficiency of 22.5 cd/A and power efficiency of 7.4 lm/W at a luminance of 1000 cd/$m^2$.

• Journal of Power Electronics
• /
• v.11 no.3
• /
• pp.285-293
• /
• 2011

This paper proposes two SRM driving systems using a variable dc-link voltage controlled by a single-phase inverter. Two SRM converter topologies of a half bridge type and a full bridge type are proposed according to the power circuits of an inverter. The phase current can be controlled by means of a PWM controller at the inverter, and the turn-on/off angle at the phase switches can be controlled by a position sensor at the converter in the drive system. The inverter acts as a peak-current limiter if the transient current exceeds its maximum value. SRMs using the proposed topologies maintain high efficiency due to energy regeneration after the turn-off of power switches. The operational modes of the proposed topologies are verified by simulation and experimental results.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.13 no.3
• /
• pp.35-40
• /
• 2005

In the present study, the influence of operating conditions on fuel economy for hybrid electric vehicle was analyzed. In order to accomplish this, vehicle speed, engine speed, battery current and voltage, SOC (state of charge),motor speed and torque, generator speed and torque, engine coolant temperature etc. were measured in real time. The tests were carried out under different driving cycles which are urban and highway cycles, KOREA CITY cycle and on-road driving, and also under various operating conditions such as different initial SOC, with or without regenerative braking etc.. Generally, conventional gasoline engines show a poor fuel economy at stop and go driving, because braking energy is wasted and the engine is operated in low thermal efficiency regions. However, in case of hybrid vehicles, higher fuel economy can be obtained because of utilizing the maximum thermal efficiency regions of engine, idling stop of engine, and regenerative braking etc..

• Journal of Biomedical Engineering Research
• /
• v.43 no.5
• /
• pp.319-330
• /
• 2022

In this study, the optimal driving frequency was derived through finite element analysis (FEA) to optimize the developed piezoelectric ultrasonic medical devices(PUMD) for bone surgery. The core of the PUMD is the piezoelectric ceramic (PZT), which is a vibrator that generates vibration energy. The piezoelectric ceramic shows the maximum current value with respect to the input voltage at the resonance frequency, which generates the maximum mechanical vibration. In the past, various studies have been conducted related to the analysis of PUMD, but most of the research so far has been limited to free vibration analysis. However, in order to derive the accurate resonant frequency, the initial stress generated by bolt tightening in the bolt-clamped Langevin type transducer (BLT) must be considered. In this study, after designing a PUMD, the driving performance according to the bolt tightening value was analyzed through FEA, and this was experimentally verified. First, the resonance mode and frequency response were confirmed through modal and harmonic analysis at 20-40 kHz, which is known as the optimal driving frequency band of PUMD for bone surgery. In addition, the design of the PUMD was confirmed by checking the mechanical behavior of the tip and the piezoelectric ceramic at the resonant frequency. Consequentially, the characteristic evaluation was performed, and it was confirmed that the resonant frequency result derived through the FEA was reasonable. Through this study, we presented a more rational FEA method than before for BLT transducers. We expect that this will shorten the time and cost of developing a PUMD, and will enable the development of more stable and high-quality products.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.28 no.9
• /
• pp.1245-1254
• /
• 2004

In this paper, we deal with a precise position synchronous control of four-axes system which is working under various load disturbances. Each axis driving system is consisted of a speed controller and an acceleration controller as an inner loop instead of conventional current control scheme. The acceleration control plays an important roll to suppress load disturbances quickly. Also, each axis is coupled by a maximum position synchronous error comparison to minimize position synchronous errors according to integration of speed differency. As a result, the proposed system enables precise synchronous control with good robustness against load disturbances during transient as well as steady state. The stability and robustness of the proposed system are investigated through its frequency characteristic and numerical simulations. Finally, experimental results under load disturbances demonstrate the effectiveness of the proposed control system fur four-axes position synchronous control.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.8 no.2
• /
• pp.207-212
• /
• 2013

A novel pixel circuit that uses only n-type low-temperature polycrystalline silicon (poly-Si) thin-film transistors (LTPS-TFTs) to compensate the threshold voltage variation of a OLED driving TFT is proposed. The proposed 6T1C pixel circuit consists of 5 switching TFTs, 1 OLED driving TFT and 1 capacitor. When the threshold voltage of driving TFT varies by ${\pm}0.33$ V, Smartspice simulation results show that the maximum error rate of OLED current is 7.05 % and the error rate of anode voltage of OLED is 0.07 % at Vdata = 5.75 V. Thus, the proposed 6T1C pixel circuit can realize uniform output current with high immunity to the threshold voltage variation of poly-Si TFT.

• Journal of the Korea Convergence Society
• /
• v.8 no.3
• /
• pp.31-40
• /
• 2017

The rise of eco-friendly personal electric mobility is a worldwide trend and the first Korean-made IT convergence electric skateboard, Youth Board, is developed to lead the trend. Youth Board is remotely controllable using either Youth Wearable Controller or Youth App through Bluetooth v4.0 communication, can speed up to 25 km/hr, and operating time is approximately 1.5 hr. A LED display located in the front side of Youth Board deck shows three different states to a rider for user convenience: remaining battery SOC, current driving speed, and braking amount. Indoor EMC test results between Youth Board and Youth Wearable Controller and outdoor Youth Board driving test results are analyzed. In particular, driving test results show the maximum current output is about 15% lowered compared to the other competitor electric skateboard and it lessens the power burden of the motor ESC. These results show Youth Board's usefulness as a personal mobility in the sense of small, light, and inexpensive aspects.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2009.10a
• /
• pp.847-849
• /
• 2009

Usually, after the decisions of the performance and range in the commercial vehicle, it is designed the ratings of the electric and mechanical elements for the vehicles. In this paper, the given performance and driving conditions, which are the maximum velocity, mileage, total weight of the normal gasoline scooter, battery type and size, and so on, are analysed for the design of the electric scooter. The maximum rotational speed and needed torque values of the electric motor which is substituted for the gasoline engine are calculated. These values can help to calculate the rating of the electric motor. In the calculation to obtain the torque and speed values, battery discharge and the running resistances are considered. We can decide the electric motor current value from the torque and speed values. The electric motor current values, which are significant parameter to decide the motor type and dimensions and characteristics of the electric motor, are decided by numerical simulation by the above conditions.

• Journal of Magnetics
• /
• v.16 no.1
• /
• pp.71-73
• /
• 2011

Hybrid electric vehicles have attracted much attention of late, emphasizing the necessity of developing traction motors with a high input current and a wide speed range. Among such traction motors, various researches have been conducted on interior permanent-magnet synchronous motors (IPMSMs) with high power density and mechanical solidity. Due to the complexity of its parameters, however, with nonlinear motor characteristics and current vector control, it is actually difficult to accurately estimate the base speed within an actual operating speed range or a voltage limit. Moreover, it is impossible to construct an efficiency map as the efficiency differs according to the control mode. In this study, a simulation method for operation performance considering the nonlinearity of IPMSM was proposed. For this, datasets of various nonlinear parameters were made via the finite-element method and interpolation. Maximum torque-per-ampere and flux-weakening control were accurately simulated using the datasets, and an IPMSM efficiency map was accurately constructed based on the simulation. Lastly, the validity of the simulation was verified through tests.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2007.11a
• /
• pp.279-285
• /
• 2007

Since the residential load is an AC load and the output of solar cell is a DC power, the photovoltaic system needs the DC/AC converter to utilize solar cell. In case of driving to interact with utility line, in order to operate at unity power factor, converter must provide the sinusoidal wave current and voltage with same phase of utility line. Since output of solar cell is greatly fluctuated by insolation, it is necessary that the operation of solar cell output in the range of the vicinity of maximum power point. In this paper, DC/AC converter is three phase PWM converter with smoothing reactor. And then, feedforward control used to obtain a superior characteristic for current control and digital PLL circuit used to detect the phase of utility line.