• Journal of the Korean Wood Science and Technology
• /
• v.25 no.3
• /
• pp.83-95
• /
• 1997

The degradation mode of lignocellulose by anaerobic ruminal cellulolytic bacterium Ruminococcus albus F-40 was investigated. Birchwood holocellulose and filter paper were incubated as the sole carbohydrate sources with using the Hungate techniques. After 2 or 4 days of incubation, samples were employed for chemical and electron microscopic evaluations. The degradation rate of cellulosic substrates and the adhesion rate of bacteria to the substrates increased proportionally with the decrease of relative crystallinity of cellulose, indicating the preferential breakdown of amorphous cellulose, by this bacterium. X-ray diffraction analyses and polarized light microscopy showed, however, that crystalline cellulose was also degraded by R. albus. FT-IR spectra indicated that not only cellulose but hemicellulose was also degraded by this bacterium. Electron microscopic investigations showed the protuberant structures on the surface of R. albus. These structures were much more significant when bacterial cells were grown in the media containing insoluble substrates, such as cellulose, indicating clearly that bacterial protuberant structures were induced by the substrates. Protuberant structures extended from the bacterial cells adhered tightly to the substrates and numerous vesicles covered the surface of cellulosic substrates affected. Cellulosome-like structures were distributed on the cellulose matrix. Electron microscopic works showed that diverse surface organells of R. albus were involved in the degradation of cellulosic materials. SEM examinations showed the breakdown of cellulose by R. albus was proceeded by severeal routes : short fiber formation, defibrillation and destrafication of cellulose microfibril.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.180-180
• /
• 2010

Thin film transistors (TFTs) based on oxide semiconductors have emerged as a promising technology, particularly for active-matrix TFT-based backplanes. Currently, an amorphous oxide semiconductor, such as InGaZnO, has been adopted as the channel layer due to its higher electron mobility. However, accurate and repeatable control of this complex material in mass production is not easy. Therefore, simpler polycrystalline materials, such as ZnO and $SnO_2$, remain possible candidates as the channel layer. Inparticular, ZnO-based TFTs have attracted considerable attention, because of their superior properties that include wide bandgap (3.37eV), transparency, and high field effect mobility when compared with conventional amorphous silicon and polycrystalline silicon TFTs. There are some technical challenges to overcome to achieve manufacturability of ZnO-based TFTs. One of the problems, the stability of ZnO-based TFTs, is as yet unsolved since ZnO-based TFTs usually contain defects in the ZnO channel layer and deep level defects in the channel/dielectric interface that cause problems in device operation. The quality of the interface between the channel and dielectric plays a crucial role in transistor performance, and several insulators have been reported that reduce the number of defects in the channel and the interfacial charge trap defects. Additionally, ZnO TFTs using a high quality interface fabricated by a two step atomic layer deposition (ALD) process showed improvement in device performance In this study, we report the fabrication of high performance ZnO TFTs with a $Si_3N_4$ gate insulator treated using plasma. The interface treatment using electron cyclotron resonance (ECR) $O_2$ plasma improves the interface quality by lowering the interface trap density. This process can be easily adapted for industrial applications because the device structure and fabrication process in this paper are compatible with those of a-Si TFTs.

• Journal of Korea Water Resources Association
• /
• v.35 no.3
• /
• pp.295-306
• /
• 2002

The modified TOPMODEL of two storage systems has been integrated to the generalized assumptions of decreasing hydraulic conductivity to vertical direction. Three different recharge functions were introduced to explore the impact of the macropore flow to vortical direction, the storage at the surface zone and the relative storage deficit of the soil matrix. Combinations of these approaches provide 30 type of the model structure for the hillslope hydrology. Developed models have been applied to several hydrologic events at the Sulmachun watershed. The performance evaluation with the Monte carlo simulation suggests that the exponential function of transmissivity reduction should be appropriate form for the physically -based hydrologic simulation on the Sulmachun watershed. It has been shown that the recharge function of macropore flow contributes to improve the predictability of the generalized version of modified TOPMODEL.

• Korean Journal of Materials Research
• /
• v.24 no.5
• /
• pp.259-265
• /
• 2014

$ZrO_2$ films were coated on aluminum etching foil by the sol-gel method to apply $ZrO_2$ as a dielectric material in an aluminum(Al) electrolytic capacitor. $ZrO_2$ films annealed above $450^{\circ}C$ appeared to have a tetragonal structure. The withdrawal speed during dip-coating, and the annealing temperature, influenced crack-growth in the films. The $ZrO_2$ films annealed at $500^{\circ}C$ exhibited a dielectric constant of 33 at 1 kHz. Also, uniform $ZrO_2$ tunnels formed in Al etch-pits $1{\mu}m$ in diameter. However, $ZrO_2$ film of 100-200 nm thickness showed the withstanding voltage of 15 V, which was unsuitable for a high-voltage capacitor. In order to improve the withstanding voltage, $ZrO_2$-coated Al etching foils were anodized at 300 V. After being anodized, the $Al_2O_3$ film grew in the directions of both the Al-metal matrix and the $ZrO_2$ film, and the $ZrO_2$-coated Al foil showed a withstanding voltage of 300 V. However, the capacitance of the $ZrO_2$-coated Al foil exhibited only a small increase because the thickness of the $Al_2O_3$ film was 4-5 times thicker than that of $ZrO_2$ film.

• Journal of the Korean Society for Heat Treatment
• /
• v.10 no.1
• /
• pp.1-9
• /
• 1997

The variation of the mechanical properties and the formation of retained austenite with heat treatment conditions in austempered Si bearing carbon steels has been investigated. In the case of a steel containing 0.35C-1.48Si-0.95Mn, it has been found that a feather shape bainite structure of lath are obtained under a isothermal treated condition at just below the Ms temperature, and the martensite, bainitic ferrite and retained austenite of second phase particles on the ferrite matrix for a isothermal treated steels after intercritical annealing are precipitated in a linked shape. The retained austenite with $2{\mu}m$ size induced as TRIP is found to increase with increasing the formation rate of retained austenite for the intercritical annealing and high Si containing steels. The tensile strength is increased as austempering temperature increases in all isothermal treatment temperature, whereas the elongation is shown to roughly decrease as the tensile strength increases. The values of tensile strength-elongation balance have showed a marked dependence upon the elongation rather than the tensile stregth, and their values are increased for high Si containing steels and intercritical annealing condition. The most optimum result has been shown to be the tensile stregth-elongation balance of $2882.4kgf/mm^2.%$ and the elongation of 33.3% for a "B" steel in the heat treating temperature range of $780{\sim}370^{\circ}C$.

• Proceedings of the Korea Institute of Fire Science and Engineering Conference
• /
• 1997.11a
• /
• pp.130-137
• /
• 1997

Intumescent inorganic and organic coatings which dintr one from the other by the type of gas formers and the mechanisms of foam formation have been obtained and investigated. Inorganic intumescent coatings are the compositions based on water glass and mineral additives with different dispersity. Mineral additives contain adsorbed and absorbed water and carbonates which are destructed with the carbon dioxide and water evolution during the flame action on coating. The decreasing of mineral additives particle sizes under the mechanical milling with the fraction precipitation promotes the foam coke formation with less defects. Here the main structure of comparing compositions does not change. In organic coatings based on epoxy-polymers the polyammonium phosphate additive is used. It is the cabonization catalyst and the foam agent. The polyammonium phosphate of various dispersity employed is uniformly distributed on the polymeric matrix. The decreasing of the particle sizes leads to the increasing of the fire resistant properties of the intumescent coa-ting. The fire resistant analysis of the coating during more than an hour: the coating back side the temperature on plastic or wooden materials does not exceed 423K, and on metal-573K.

• Food Science and Biotechnology
• /
• v.15 no.3
• /
• pp.447-452
• /
• 2006

To determine the functions of specific cell wall polysaccharides, polysaccharides of three mutants, mur3-1, mur3-2, and mur3-3, obtained from Arabidopsis wild type, underwent structural characterization. Upon sequential separation of pectins (RG-I and RG-II) and cross-linking glycans (xyloglucan, XG), only XG was affected by the mud mutation. Wild-type XG contained a considerable amount of fucose, whereas the fucose level in mur3 XGs was less than 20% that of wild type. Further analysis of XGs by matrix-assisted laser-induced/ionization time-of-flight (MALDI-TOF) mass spectrometry indicated that mud lines considerably or completely lost the fucosylated XG oligosaccharides such as XXFG and XLFG and the double-galactosylated oligosaccharide XLLG $^1H$-NMR spectroscopic analyses of the XG oligosaccharides from mur3-3 plant revealed the absence of fucose and a galactose level in the galactosylated side chain that was reduced by 40% compared to that of Arabidopsis wild-type plant. In contrast, 85% less fucose and a slight loss of galactose were observed in the mur3-1 and mur3-2 lines which show normal growth habit. Of the three Arabidopsis mur3 lines studied here, mur3-3 is disrupted by a T-DNA insertion in the exon of MUR3 which encodes XG-specific galactosyltransferase, and exhibits slight dwarfism. These results indicated that the T-DNA insertion at the MUR3 locus did not induce the complete loss of galactose in XG, and that galactose, rather than fucose, in the XG side chains made a major contribution to overall wall strength.

• Journal of the Korea Computer Industry Society
• /
• v.3 no.3
• /
• pp.259-270
• /
• 2002

In computer Go, the method evaluating the situation of a face is not generalized. To evaluate the situations all the faces accurately, computer Go must judge owners of 361 positions according the changes of the faces. In this paper, we apply the structure of graph as a method analyzing the rules and characters of Go. The Situation Evaluation System(SES) which can evaluate the situation of a face without DB information oかy using strength of stone(SS), influence power(IP), safety(S), position value(PV), and position-value matrix(PM) is proposed. This system is very effective to evaluate the whole situations of Go because it can show the owner of 361 positions between Black and White. As a result, SES can well compute the situations in the opening game of Go. It makes 70.9% hit-ratio as compared with the practical Go games of professional players. According to the results compared with Nemesis, the commercial program which has the joseki(established stones: hewn sequences of moves near the corner which result in near-equal positions for White and Black), SES is superior to Nemesis by 10% higher in the hit-ratio of situation evaluations of professional players.

• Journal of Radiation Industry
• /
• v.6 no.2
• /
• pp.159-164
• /
• 2012

Bacterial cellulose (BC) is generated from citrus gel by Gluconacetobacter hansenii TL-2C. BC has good properties such as high-burst pressure, high-water contact and the ultrafine highly nanofibrous structure of mimic natural extracellular matrix (ECM) for tissue engineering. In this study, acrylic acid (AAc) was grafted onto BC surfaces under aqueous conditions using gamma-ray irradiation, and then immobilized gelatin onto AAc-g-BC. The characterization of scaffolds was performed by scanning electron microscopy (SEM), attenuated total reflectance-Fourier transform infrared spectroscopy (ATR-FTIR), toluidine blue O (TBO) assay. Morphology of gelatin and AAc incorporation onto BC nanofibers did not changed. Our study suggests that gelatin-immobilized BC nanofibers scaffold has a potentiality to fabricate 3D nanofibrous scaffolds for tissue engineering.

• Korean Journal of Metals and Materials
• /
• v.50 no.11
• /
• pp.829-838
• /
• 2012

The microstructure, chemical composition, and lead isotope ratio of the Buddhist bell of Yongmoon Mountain Sangwonsa temple, which was selected as one of the three great bells of Korea by Japanese historians, were analyzed in order to estimate the origin of the material and the time of casting. The microstructure of the temple bell was composed of a copper matrix phase with ${\alpha}$, a face centered cubit lattice structure, a ${\delta}$ phase with $Cu_{41}$ $(Sn,Ag,Sb)_{11}$ as the chemical structural formula, dispersed lead and $Cu_2S$ particles, and locally agglomerated fine particles. Through analysis of the chemical composition of the bell, a criterion (Pb: 0-3.0 wt%, Sn: 10-15 wt%) for distinguishing the bells of the Shilla dynasty from the bells of the Koryo Chosun dynasty is proposed. Examining the lead isotope ratio of $^{207}Pb/^{206}Pb$ and $^{208}Pb/^{206}Pb$ of the Buddhist bell of Sangwonsa temple proved that the bell was fabricated using raw materials in South Korea, which led to the conclusion that the bell was cast in Korea and the top board of the bell has been damaged by an unknown individual. The criteria of distinguishing the bells from the Shilla dynasty from the bells of the Koryo Chosun dynasty presented for the first time in this research is expected to aid in identifying and estimating the previously unclear production years of other bells.