• Journal of Korea Foundry Society
• /
• v.13 no.6
• /
• pp.524-531
• /
• 1993

Dispersion behaviors of SiC particles and microstructures in Al-2%Si/SiCp composite prepared by Rheo-compocasting were studied with change of fabrication conditions(slurry temperature, agitation time) and additions of Mg($0{\sim}3wt.%$). Also, the microhardness change of matrix, interface and total in composites were examined with additions of Mg($0{\sim}3wt.%$). The dispersion of particles in the composites became relatively homogeneous with increase of Mg additions, agitation time and decrease of slurry temperature. Rate of occupied area by particle in matrix was increased as increase of Mg additions due to improvement of wettability between SiC particle and matrix. A favorable composites were obtained by melting under Ar atmospheric SiCp injection and bottom pouring system. According to the analysis of X-ray diffraction, $Mg_2Si$, $Al_4C_3$, $SiO_2$ and MgO, etc, intermetallic compounds were formed by chemical interreaction at interface of matrix and particles. The microhardness of interface is higher than that of matrix due to more strengthening of above intermetallic compounds. It was considered that the total hardness of the composites is improved by dispersing of SiCp and addition of Mg.

• Bulletin of the Korean Chemical Society
• /
• v.34 no.5
• /
• pp.1435-1440
• /
• 2013

To investigate the influence of the carbon matrix on the electrochemical performance of Si/C composites, four types of Si/C composites were prepared using graphite, petroleum coke, pitch and sucrose as carbon precursors. A ball mill was used to prepare Si/C blends from graphite and petroleum coke, whereas a dispersion technique was used to fabricate Si/C composites where Si was embedded in disordered carbon matrix derived from pitch or sucrose. The Si/pitch-based carbon composite showed superior Si utilization (96% in the first cycle) and excellent cycle retention (70% after 40 cycles), which was attributed to the effective encapsulation of Si and the buffering effect of the surrounding carbon matrix on the silicon particles.

• Elastomers and Composites
• /
• v.53 no.3
• /
• pp.175-180
• /
• 2018

Solution-styrene-butadiene rubber (SSBR) composites were manufactured using four kinds of fillers: silica-silane coated carbon black (SC-CB) hybrid, starch-SC-CB hybrid, pure silica, and pure starch. The influence of filler type on the mechanical properties of the rubber matrix was studied in this work. SC-CB was prepared by silane-graft-coating using vinyl triethoxy silane and carbon black, which enhanced the dispersion effect between the rubber matrix and the filler, and improved the mechanical properties of the compounds. The morphology of the composites was observed by field-emission scanning electron microscopy (FE-SEM). The thermal decomposition behavior of the composites was determined by thermogravimetric analysis (TGA), and the crosslinking behavior of the composites was tested using a rubber process analyzer (RPA). The hardness, tensile strength, swelling ratio, and gas transmittance rate of the composites were evaluated according to ASTM. The test results revealed that with the addition of SC-CB, the hybrid fillers, especially those blended with silica, showed a better reinforcement effect, the highest hardness and tensile strength, and stable thermal decomposition behavior. This implies that the silica-SC-CB hybrid filler has a notable mechanical reinforcement effect on the SSBR matrix. Because of self-crosslinking during its synthesis, the starch-SC-CB hybrid filler produced the most dense matrix, which improved the anti-gas transmittance property. The composites with the hybrid fillers had better anti-swelling properties as compared to the neat SSBR composite, which was due to the hydrophilicity of silica and starch.

• Composites Research
• /
• v.32 no.1
• /
• pp.1-5
• /
• 2019

In this study, Al1050 composites reinforced with uniformly dispersed, high volume fraction $TiB_2$ particles were fabricated by liquid pressing process and analyzed to microstructure, mechanical properties. Hardness, ultimate tensile strength and compressive yield strength of the 56 vol.% $TiB_2$-Al1050 composite increased to 10, 4.5 and 9.8 times, respectively, compared with those of the Al1050 due to dispersion hardening effect of uniformly dispersed $TiB_2$ in the Al matrix.

• Journal of the Korean Ceramic Society
• /
• v.51 no.1
• /
• pp.32-36
• /
• 2014

The effects of an amphiphilic agent and the orientation of BN on the microwave dielectric properties of BN / polyvinyl butyral (PVB) composites were investigated as a function of the BN content in volume fractions from 0.1 to 0.5 ($V_f$). The plate-shaped BN samples were oriented in the PVB matrix by physical processes, in this case tape casting and laminate methods. With an increase in the BN content, the dielectric constant (K) increased because the K of BN was higher than that of the PVB. At the same BN content, composites with an in-plane orientation of the BN showed a higher dielectric constant than that of composites with a transverse orientation of the BN because the ceramics were oriented parallel to the electric field. All of the composites showed nearly constant K values ranging from 1 to 9.4 GHz, indicating good frequency stability over a wide frequency range. At the same frequency, the K values of the composites increased with an increase in the BN content.

• Composites Research
• /
• v.34 no.2
• /
• pp.82-87
• /
• 2021

The mechanical properties of carbon fiber-reinforced epoxy composites (CFRPs) are greatly dependent on the interfacial adhesion between the carbon fibers and the epoxy matrix. Introducing nanomaterial reinforcements into the interface is an effective approach to enhance the interfacial adhesion of CFRPs. The main purpose of this work was to introduce graphitic nanofiber (GNFs) between an epoxy matrix and carbon fibers to enhance interfacial properties. The composites were reinforced with various concentrations of GNFs. For all of the fabricated composites, the optimum GNF content was found to be 0.6 wt%, which enhanced the interlaminar shear strength (ILSS) and fracture toughness (KIC) by 101.9% and 33.2%, respectively, compared with those of neat composites. In particular, we observed a direct linear relationship between ILSS and KIC through surface free energy. The related reinforcing mechanisms were also analyzed and the enhancements in mechanical properties are mainly attributed to the interfacial interlocking effect. Such an effort could accelerate the conversion of composites into high performance materials and provide fundamental understanding toward realizing the theoretical limits of interfacial adhesion and mechanical properties.

• Korean Journal of Materials Research
• /
• v.20 no.9
• /
• pp.467-471
• /
• 2010

Composites of ceramic powders and an elastomer-based matrix were prepared by mixing $CaCO_3$ powders with polyethylene and polypropylene elastomers, and their mechanical and sound insulation properties were measured. $CaCO_3$ powders with 0.7 ${\mu}m$ and 35 ${\mu}m$ particle size were added to elastomers up to 80 wt%. Scanning electron microscopy photographs showed uniform distribution of the $CaCO_3$ powders in the matrix. While density and surface hardness increased, melt index, tensile strength and elongation of the composites decreased as the amount of added $CaCO_3$ powders increased. As more $CaCO_3$ powders were added sound transmission loss of the composites increased owing to the increase of density. Addition of 0.7 ${\mu}m$ sized $CaCO_3$ powders resulted in a slightly higher transmission loss than the addition of 35 ${\mu}m$ sized powders because of the increased interface area between the elastomer matrix and the $CaCO_3$ powders. Composites with a polyethylene matrix showed higher transmission loss than those with a polypropylene matrix because the tensile strength and hardness of the polyethylene-based composites were low and their elongation was high.

• Advanced Composite Materials
• /
• v.17 no.2
• /
• pp.157-166
• /
• 2008

In this study, multiwalled carbon nanotubes (MWCNTs) were compounded with the poly($\varepsilon$-caprolactone) (PCL) matrix at the solution state using chloroform. For homogeneous dispersion of MWCNTs in polymer matrix, oxygen-containing groups were introduced on the surface of MWCNTs. The mechanical properties of the PCL/MWCNTs composites were effectively increased due to the incorporation of MWCNTs. The composites were characterized using scanning electron microscopy in order to obtain information on the dispersion of MWCNT in the polymeric matrix. In case of 1.2 wt% of MWCNTs in the matrix, strength and modulus of the composite increased by 12.1% and 164.3%, respectively. In addition, the dispersion of MWCNTs in the PCL matrix resulted in substantial decrease of the electrical resistivity of the composites as the MWCNTs loading was increased from 0 to 2.0 wt%. Furthermore, thermal stability of the PCL and PCL/MWCNTs-COOH composites were investigated using the data acquired from the thermogravimetric analysis. The detailed kinetics of the thermal degradation of the composites was investigated by analyzing their thermal behavior at different heating rates in a nitrogen atmosphere. Activation energy of thermal degradation was determined by using the equations proposed by Kissinger and Flynn-Wall-Ozawa. The apparent activation energy of PCL/MWCNTs-COOH composite was considerably higher than that of neat PCL.

• Carbon letters
• /
• v.2 no.3_4
• /
• pp.192-201
• /
• 2001

The Carbon/Carbon composite was prepared from 3D carbon fiber preform and coal tar pitch as matrix precursor. In order to evaluate of ablative characteristics of the composite, liquid rocket system was employed Kerosene and liquid oxygen was used as propellants, operating at a nominal chamber pressure of 330 psi and a nominal mixture ratio (O/F) of 2.0. The results of an experimental evaluation were that high density composite exhibited high, while low density composites showed low erosion resistance. The erosion rate against heat flux was highly depended on the density of the materials. The morphology of eroded fiber showed differently according to collision angle with heat flux on the composite. The granular matrix which derived from carbonization pressure of 900 bar was more resistance to heat flux than well-developed flow type matrix.

• The Korean Journal of Ceramics
• /
• v.5 no.1
• /
• pp.55-72
• /
• 1999

A cheallenge in the aerospace field is to design new composites satisfying specific and sometimes conflicting properties. The key steps are ⅰ)the understanding and the control of the reaction between the reinforcement and the embedding matrix, ⅱ) the achievement of a coherent and robust matrix. The problems encountered to prepare particulate, 1D, 2D and 3D reinforced composites using polymeric are discussed. Emphasis is given to the control of the micro/nanostructure using Raman microspectrometry and depth-sensing microindentation, in order to get information on the micromechanics and fiber structure simultaneously, within ceramic (CMC's) and metal matrix (MMC's) composites.