• Polymer(Korea)
• /
• v.25 no.4
• /
• pp.587-593
• /
• 2001

In this work, red mud (RM) was chemically modified by 0.1, 1, and 5 M H3PO4 solution to prepare epoxy/RM nanocomposites. The effect of chemical treatment on pH, acid-base values, specific surface area, and porosity of RM surface was analyzed. To estimate the mechanical interfacial properties of epoxy/RM nanocomposites, the critical stress intensity factor (K$_{IC}$) was measured. From the experimental results, it was clearly revealed that the porosity, specific surface area, and acid values of RM surface were developed as the increase of the treatment concentration due to the increase of acidic functional group, including hydroxyl group on RM surface. The mechanical interfacial properties of epoxy/treated-RM nanocomposites were higher than those of epoxy/RM as-received due to an improvement of interfacial bonding between basic matrix and RM surface.

• Polymer(Korea)
• /
• v.26 no.1
• /
• pp.1-8
• /
• 2002

In this study, poly(arylene ether sulfone) (PAES) having thermal stability and excellent mechanical properties was synthesized to be useful for the matrix of anion exchange resin. $1^{\circ}$-Aminated poly(arylene ether sulfone) ($1^{\circ}$-APAES) was prepared by reduction reaction after lithiation of PAES. Then $3^{\circ}$-APAES was Prepared by alkylation of the amino group of $1^{\circ}$-APAES. The structures of PAES and APAESs were confirmed with FT-IR and $^1H-NMR$ spectroscopy. Also, thermal properties of the resins were characterized by DSC and TG analysis. The introduction of amine groups in PAES resulted in the increase of glass transition temperature and decrease of initial thermal degradation temperature. The ion exchange capacities of $1^{\circ}$-APAES and $1^{\circ}$-APAES were 1.19 and 1.45 meq/g, respectively.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.25 no.3
• /
• pp.211-217
• /
• 2012

In this paper, experimental tests and theoretical studies were carried out to evaluate the tensile behavior of the sprayed FRP composite with chopped glass fiber. For this, a series of tensile strength tests with various strain rates were conducted on the specimens of the matrix and sprayed FRP composite. Sprayed FRP composite contained chopped glass fibers with fiber length of 15mm and a specific volume fraction of fibers of 25 %. An inverse simulation was conducted to simulate the strain rate sensitivity based on the present experimental data of the epoxy resin. The simulated viscosity value is adapted to the micromechanics-based viscoelastic damage model(Yang et al., 2012), and the overall tensile behavior of sprayed FRP composites is predicted. It was seen from the comparative study between present experimental data and predication results that the proposed methodology can be used to predict the viscoelastic behavior of the sprayed FRP composite.

• Composites Research
• /
• v.28 no.6
• /
• pp.389-394
• /
• 2015

The sound absorption coefficient and sound transmission loss of graphite intercalation compound (GIC) included epoxy composites were investigated. Epoxy resin was infused into the expanded GIC and the impedance tube method was employed to measure the sound absorption coefficient and sound transmission loss. Scanning electron microscopy photographs showed uniform distribution of the GIC in the epoxy matrix. The surface density of epoxy/GIC (20 wt%) composites decreased about 56% compared to that of pure epoxy. The sound absorption coefficient of composites increased about 3 times at the frequency range of 500~1000 Hz compared to the pure epoxy. The sound transmission loss of composites decreased with increasing the GIC content and it is attributed to the increase of pores in the composites.

• Composites Research
• /
• v.33 no.3
• /
• pp.91-100
• /
• 2020

Polyphenylene sulfide (PPS) is a semi-crystalline engineering thermoplastic resin that has outstanding thermal stability, mechanical strength, inherent flame retardancy, chemical resistance, and electrical properties. Due to these outstanding properties, it is preferred as a matrix for composite materials. Many studies have been conducted to produce composites with carbon fibers and glass fibers to improve mechanical properties and provide functionality of PPS. In this review paper, we report a brief introduction to the fabrication and applications of PPS composites with carbon nanotubes, graphene, carbon fibers, and glass fibers.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2004.04a
• /
• pp.182-185
• /
• 2004

In this work, the effect of chemical treatments on surface properties of SiC was investigated in mechanical interfacial properties of carbon fibers-reinforced composites. The surface properties of the SiC were determined by acid/base values and contact angles. The thermal stabilities of carbon fibers-reinforced composites were investigated by thermogravimetric analysis (TGA). Also, the mechanical interfacial properties of the composites were studied in interlaminar shear strength (ILSS) and critical strain energy release rate mode II $(G_{IIC})$ measurements. As a result, tile acidically treated SiC (A-SiC) had higher acid value than that of untreated SiC (V-SiC) or basically treated SiC (B-SiC). According to the contact angle measurements, it was observed that chemical treatments led to an increase of surface free energy of the SiC surfaces, mainly due to the increase of the specific (polar) component. The mechanical interfacial properties of the composites, including ILSS and $(G_{IIC})$, had been improved in the specimens treated by chemical solutions. These results were explained that good wetting played an important role in improving the degree of adhesion at interfaces between SiC and epoxy resin matrix.

• Polymer(Korea)
• /
• v.29 no.5
• /
• pp.481-485
• /
• 2005

In this work, the thermal and mechanical properties of vapor grown carbon nanofibers (VGCNFs)-reinforced difunctional epoxy (EP) composites were investigated in the presence of the 0, 0.1, 0.5, 1.0, and $2wt\%$ VGCNFs. The thermal properties of the VGCNFs/EP composites were studied by thermo-mechanical analysis (TMA) and dynamic mechanical analysis (DMA). The mechanical properties of the VGCNFs/EP composites were also examined by universal testing machine (UTM), falling impact test, and the friction and wear tests. From experimental results, the thermal and mechanical properties of the VGCNFs/EP composites were improved with increasing the VGCNFs contents. This was due to the increase of crosslinking structure of the composites, resulting in improving the mechanical interlockings between VGCNFs and epoxy resins in the present composite system.

• Polymer(Korea)
• /
• v.29 no.1
• /
• pp.102-105
• /
• 2005

Photoinitiated polymeric dental restorative nanocomposites (PDRNC) were designed to be useful for the variety of dental restoration. Hybrid-filler composed of barium silicate (avg. dia.:1 ${\mu}m$) and nano-sized silica (avg. dia: 40 and 7 nm) was adopted as a filler system. To improve the interfacial behavior with the resin matrix of bisphenol A glycerolate methacrylate/triethyleneglycol dimethacrylate (60/40 wt%), the surface of the filler was hydrophobically treated with a silane coupling agent. A visible light system of camphorquinone photo-initiator and 2-(dimethylamino)ethyl methacrylate photo-accelerator was utilized to activate the PDRNC. Esthetic properties of PDRNC was investigated by measuring the Hunter L, a, b values and it was discovered that PDRNC produced in this work showed excellent esthetic properties with an increase in 7 nm nanofiller content.

• Polymer(Korea)
• /
• v.31 no.2
• /
• pp.141-147
• /
• 2007

Dental properties of polymer composite loaded with hybrid filler of barium silicate (BaSi) and hydroxyapatite, which is a principal component of human bone material, were investigated. A visible light system was utilized to activate the acrylic resin matrix of the composite. Based on the experimental results, it was found that mechanical strength of the composite was consistently increased with an increase of BaSi content in the hybrid filler. And those value rose above the dental specification enough to apply for dental materials. However, abrasion resistance was slightly decreased with increasing BaSi content in the filler. Depth of cure value was 6 to 9 mm applicable for dental restoration irrelevant to hybrid filler composition. On the other hand, there was no strict trend between filler composition and polymerization shrinkage as well as degree of conversion.

• Korean Journal of Materials Research
• /
• v.3 no.3
• /
• pp.292-299
• /
• 1993

In this paper the effects of the length of carbon fiber on the wear properties of carboni carbon composites were investigated. Carbon/carbon composites were fabricated by the liquid impregnation method using the resol-type phenolic resin as a matrix precursor and PAN-based, non-surface treated carbon fiber as a reinforcement. The measured values of the friction coefficient of carbon/carbon composites against AlSl 304 stainless steel ranged from 0.2 to 0.3 under the operating condition used in this study. The effect of the length of carbon fiber on the friction coefficient of carbon/carbon composites were not found. But, it was realized that the wear rate of carbon/carbon composites tends to increase, as the length of carbon fiber increases.