• 제어로봇시스템학회:학술대회논문집
• /
• 1997.10a
• /
• pp.1512-1515
• /
• 1997

One of the advantages of master-slave teleoperation is scaling concept such as position scaling, force scaling Meanuhile, lots of quantization effects are generated from position and force sensors in the master and slave manipulator. In this paper, to show the output error caused by the quantizaion effects from the position sensor and position scaling factor, simulation is done for free motion without contact in slave side. Transfer functiion model in which the quantization effect is assumed to be a disturbance input to the system is derived. Model shows that Jacobian, scaling factors, and controller affect the output by quantization effects form esnsors. One dof master and slave are used for simulation. In our study, the higher sensor resolution decreases the output error form quantization. Scaling factors can amplify the quantizatiion effects form the sensors in master and slave manipulators.

• Proceedings of the KIEE Conference
• /
• 2000.07d
• /
• pp.2760-2762
• /
• 2000

The objective of this paper is to design a force feedback controller for bilateral control of a master-slave manipulator system. In a bilateral control system. the motion of the master device is followed by the save one. while the force applied to the slave is reflected on the master. In this paper, a proposed controller applied to the system. Adding a switching control term to control input. robustness is improved. Also the knowledge of the system dynamics is not needed. The computer simulation results show the performance of the proposed controller.

• 제어로봇시스템학회:학술대회논문집
• /
• 2002.10a
• /
• pp.108.5-108
• /
• 2002

Recently, the more advanced control technologies are required to deal with the fast and accurate motion in manipulators. For these requirements, many manipulator control methods have been developed such as a computed torque method. This paper proposes a design method, a two-degrees-of-freedom internal model control (TDOF IMC), of the manipulator position control based on combination of the one-degree-of-freedom internal model control (ODOF IMC) system and the disturbance observer. The proposed control scheme is implemented for the position control, which leads the slave manipulator to the desired location by the master arm. The experimental results are presented and discussed through the imp...

• Journal of Institute of Control, Robotics and Systems
• /
• v.6 no.7
• /
• pp.578-585
• /
• 2000

This paper presents a robust and systematic bilateral controller design method for a teleoperation of an underwater manipulator. Disturbance observer is used as a local controller of the master and underwater slave manipulator to set up the teleoperation system as a nominal model by compensating coupled nonlinear terms model uncertainties and external disturbances in the water. Using the linearized master/slave model a $H_{\infty}$ optimal control scheme is applied to systematically construct a force reflecting bilateral controller.

• Journal of Institute of Control, Robotics and Systems
• /
• v.8 no.9
• /
• pp.788-794
• /
• 2002

To improve surgical result of total hip arthroplasty (THA), there has been some approaches using a robotic milling system, which can make a precise cavity in the femur. Usually, to carve a femur, the surgical robot is controlled by a pre-programmed tool-path regardless of a surgeon's experience and Judgment. This paper presents a control method of a surgical robot for THA, which can be used as an advanced surgical tool. With a master/slave combined surgical robot, surgeon can directly control the motion and velocity of a surgical robot. The master/slave-combined robot is controlled to display a specific admittance for a surgeon's force to the surgical robot velocity. To prevent the over-carving of a femur, virtual hard wall is displayed on the surgical boundary. To evaluate the proposed control method of the master/slave-combined surgical robot, 2-DOF master/slave-combined manipulator is used in experiment.

• 제어로봇시스템학회:학술대회논문집
• /
• 2003.10a
• /
• pp.1571-1574
• /
• 2003

A shared compliant control scheme based on IMC is proposed for the position-force force reflecting control system. The controller of the slave manipulator is designed by IMC method for the open loop unstable plant. The compliant control is implemented by first order low pass filter. In the proposed scheme, the slave manipulator well tracks the position of the master manipulator in free space and the compliance of the slave manipulator is autonomously controlled in contact condition. The simulation results show that the excellence of the proposed controller.

• Journal of Institute of Control, Robotics and Systems
• /
• v.13 no.1
• /
• pp.33-38
• /
• 2007

In this paper, hardware implementation of interface and control between two robots, the master and the slave robot, are designed. The master robot is the motion capturing device that captures motions of the human operator who wears it. The slave robot is the corresponding humanoid robot arms. Captured motions from the master robot are transferred to the slave robot to follow after the master. All hardware designs such as PID controllers, communications between the master robot, encoder counters, and PWM generators are embedded on a single FPGA chip. Experimental studies are conducted to demonstrate the performance of the FPGA controller design.

• Journal of Institute of Control, Robotics and Systems
• /
• v.13 no.10
• /
• pp.940-948
• /
• 2007

The Advanced Spent Fuel Conditioning Process(ACP), which is the process of the reduction of uranium oxide by lithium metal in a high temperature molten salt bath for spent fuel, was developed at Korea Atomic Energy Research Institute (KAERI). Since the ACP equipment is located in an intense radiation field (hot cell) as well as in a high temperature, it must be remotely operated and maintained. The ACP hot cell is very narrow so the workspace of the wall-mounted mechanical Master-Slave Manipulators(MSMs) is restricted. A Bridge Transported Servo Manipulator(BTSM) system has been developed to overcome the limitation of an access that is a drawback of the mechanical MSMs. The BTSM system consists ot a bridge crane with telescoping tubeset, a slave manipulator, a master manipulator, and a control system. We applied a bilateral position-position control scheme with friction compensation as force-reflecting controller. In this paper, the transmission characteristics on the tendon-and-pulley train is numerically formulated and analyzed. Also, we evaluate the performance of the force-reflecting servo manipulator.

• Journal of Institute of Control, Robotics and Systems
• /
• v.12 no.5
• /
• pp.457-463
• /
• 2006

Recently proposed control scheme for a stable teleoperation, which was based on two-port time-domain passivity approach[21], has been successful for a contact with high stiffness environments. However, we found several conservatisms during the contact with deformable environments and unconstrained motion. The two-port time-domain passivity controller was excessively dissipating energy even though it was not necessary for some cases of an unconstrained motion and soft contact. The main reason of those conservatisms was on the fact that the two-port time-domain passivity controller was activated without considering the amount of energy dissipation at the master and slave manipulators. Especially, the exclusion of the slave manipulator from the two-port was the dominant reason of the conservatisms. In this paper, we consider the amount of energy dissipation at slave manipulator for designing the time-domain passivity observer and controller. The measured interaction force between slave manipulator and environment allow the time-domain passivity observer to include the amount of energy dissipation at the slave manipulator. Based on the modified passivity observer, reference energy following method[24] is applied to satisfy the passivity condition in real-time. The feasibility of the developed methods is proved with experiments. Improved performance is obtained for an interaction with deformable environments and an unconstrained motion.

• Journal of Institute of Control, Robotics and Systems
• /
• v.22 no.8
• /
• pp.585-589
• /
• 2016

Recently, the robotic assist system for cardiovascular intervention gets continuously growing interest. The robotic cardiovascular intervention systems are largely two folds, systems for cardiac ablation procedure assist and systems for vascular intervention assist. For the systems, the clinician controls the catheter inserted through blood vessel to the heart via a master console or master manipulator. Most of the current master manipulators have structure of joystick-like pivoting 2 degree of freedom (DOF) handle in the core, which is used in parallel with other sliding switches and input devices. It however is desirable to have customized and optimized design manipulator that can provide clinician with intuitive control of the catheter motion fully utilizing the advantage of the use of robotic structure. A 6 DOF kinematic mechanism that can capture the motion control intention of the clinician in translational 3 DOF and rotational 3 DOF is proposed in this paper. Also, a master-slave motion relationship specially designed for the cardiac catheter manipulation motion is proposed and implemented in an experimental prototype. Design revision for implementation of more efficient motion and experiment in combination with an experimental slave robot system for catheter manipulation are underway.