• Title/Summary/Keyword: Mass output

Search Result 386, Processing Time 0.032 seconds

Effects of Alcohol Intake on Body Fluid Balance and Fat Mobilization After Exercise Induced Dehydration

  • Park, Hyun-Jeong;Bae, Yoon-Jung;Lee, Joo-Hyung;Lee, Dae-Taek
    • Nutritional Sciences
    • /
    • v.9 no.2
    • /
    • pp.124-130
    • /
    • 2006
  • To examine the effects of alcohol consumption on body fluid restoration and fat mobilization following exercise induced dehydration, nine healthy collegiate men ($24{\pm}2yrs,\;177{\pm}5cm,\;72{\pm}8kg,\;10.5{\pm}2.3%$ body fat) underwent three experiments. In each experiment, subjects ran on a treadmill to reduce individual body mass to $2.2{\pm}0.1%$ and consumed one of three beverages containing 0, 4, or 8% alcohol over 60 min followed by 4 hr of resting recovery. They consumed approximately 150% of weight loss $(2053{\pm}204,\;2091{\pm}149,\;and\;1943{\pm}295mL)$ and content of alcohol was $9.9{\pm}1.0(0%),\;71.9{\pm}5.1(4%)$, and $132.2{\pm}20.1g$ (8% trial). Body weight, urine volume and samples, blood samples, and thirst sensation were measured five times; at baseline, immediately after exercise, and 0, 1st, and 4th hr of recovery. Blood alcohol concentration after ingestion was $0.0{\pm}0.0(0%),\;0.1{\pm}0.02(4%)$, and $0.2{\pm}0.03%$ (8% trial). No differences in blood sodium and potassium concentrations, and urine specific gravity were noticed over time periods and trials. Thirst sensation tended to be elevated in all trials immediately after exercises and urine output was elevated during the recovery. The magnitude of changes in these variables was proportional to the alcohol concentrations, but not statistically significant. While serum osmolality was not different among trials and time periods in 0 and 4% trials, it was higher during recovery than the baseline in the 8% trial (P<0.01). Triglycerides did not change throughout the time period and among trials. Free fatty acids were elevated after exercise in all trials and 4th hr of recovery in 0% (P<0.05). Subjects' net body fluid balance at 4th hr of recovery was negatively maintained and proportional to alcohol concentrations. Only 8% trials showed a significant reduction at 1st and 4th hr of recovery compared to 0 hr. The results suggested that diuretic effect of alcohol after moderate level of dehydration appeared dose dependent, but beverage containing alcohol up to 4% did not induce impaired rehydration than alcohol free drinks. Alcohol effects on fat mobilization during recovery appeared to be minimal and the mechanism is unclear.

A Study of Electromagnetic Actuator for Electro-pneumatic Driven Ventricular Assist Device

  • Jung Min Woo;Hwang Chang Mo;Jeong Gi Seok;Kang Jung Soo;Ahn Chi Bum;Kim Kyung Hyun;Lee Jung Joo;Park Yong Doo;Sun Kyung
    • Journal of Biomedical Engineering Research
    • /
    • v.26 no.6
    • /
    • pp.393-398
    • /
    • 2005
  • An electromechanical type is the most useful mechanism in the various pumping mechanisms. It, however, requires a movement converting system including a ball screw, a helical cam, or a solenoid-beam spring, which makes the device complex and may lessen reliability. Thus, the authors have hypothesized that an electromagnetic actuator mechanism can eliminate the movement converting system and that thereby enhance the mechanical reliability and operative simplicity of an electro­pneumatic pump. The purpose of this study was to show a novel application of electromagnetic actuator mechanism in pulsatile pump and to provide preliminary data for further evaluations. The electromagnetic actuator consists of stators with a single winding excitation coil and movers with a high energy density neodymium-iron-boron permanent magnet. A 0.5mm diameter wire was used for the excitation coil, and 1000 turns were wound onto the stators core with parallel. A prototype of extracorporeal electro-pneumatic pump was constructed, and the pump performance tests were performed using a mock system to evaluate the efficiency of the electromagnetic actuator mechanism. When forward and backward electric currents were supplied to the excitation coil, the mover effectively moved back and forth. The nominal stroke length of the actuator was 10mm. The actuator dimension was 120mm in diameter and 65mm in height with a mass of 1.4kg. The prototype pump unit was 150mm in diameter, 150mm in thickness and 4.5kg in weight. The maximum force output was 70N at input current of 4.5A and the maximum pump rate was 150 beats per minute. The maximum output was 2.0 L/minute at a rate of 80bpm when the afterload was 100mmHg. The electromagnetic actuator mechanism was successfully applied to construct the prototype of extracorporeal electro­pneumatic pump. The authors provide the above results as a preliminary data for further studies.

Dielectric Waveguide Filters Design Embedded in PCB Substrates using Via Fence at Millimeter-Wave (밀리미터파 대역에서 Via Fence를 이용한 PCB 기판용 유전체 도파관 필터 설계)

  • 김봉수;이재욱;김광선;강민수;송명선
    • The Journal of Korean Institute of Electromagnetic Engineering and Science
    • /
    • v.15 no.1
    • /
    • pp.73-80
    • /
    • 2004
  • In this paper, the implementation and embedding method of the existing air-filled waveguide-filters at millimeter-wave on general PCB substrate is introduced by systematically inserting the vias inside waveguide and mathematically manipulating the simple equations obtained ken the classical circular-post waveguide filter design. All the metal structures placed vertically such as side wall fur perfect ground plane and circular-post for signal control in the air-filled WR-22 waveguide are replaced with several types of via for constructing the bandpass-filter. Side wall and poles inside waveguide are realized by placing a series array of via and tuning the via diameter. The lengths of x, y, z axis are reduced in proportion to root square of employed substrate dielectric constant and especially the length of z axis can be more reduced due to the characteristics of the wave propagation. Because the mass production on PCB is possible without fabricating a large-scaled metal waveguide of WR-22 as input/output ports at millimeter-wave regime, the manufacturing cost is reduced considerably. Finally, when using multilayer process like LTCC for small-sized module, it is one of advantages to use only one layer f3r the filter fabrication. To evaluate the validity of this novel technique, order-3 Chebyshev BPF(Bandpass-Filter) centered at 40 GHz-band with a 2.5 % FBW (Fractional Bandwidth) were used. The employed substrate has relative dielectric constant of 2.2 and thickness of 10 mil of Rogers RT/Duroid 5880. Accroding to design and measurement results, a good performance of insertion loss of 2 ㏈ and return loss of -30 ㏈ is achieved at full input/output ports.

Development of EPICS-IOC Measuring Magnetic Field at A/Q separator for Separating Specific Ions (가속이온 분리를 위한 A/Q Separator에서 자장측정용 EPICS-IOC 개발)

  • Lee, Su-Yeong;Yim, Hee-Joong;Kim, Jae-Hong;Mun, Jun-Yeong;Park, Mi-Jeong;Lee, Sang-Il;Lee, Dong-Hoon
    • Journal of the Institute of Convergence Signal Processing
    • /
    • v.22 no.3
    • /
    • pp.91-98
    • /
    • 2021
  • The installation and performance test of the ISOL (Isotope Separation On Line) system for the generation and separation of Rare Isotopes (RI) beams is in progress at the Rare Isotope Science Project (RISP), Institute for Basic Science (IBS). The various RI beams generated by the ISOL target/ion source go through the beam lines and separators, and only the RI beam desired by the user is selected and transmitted to the superconducting linear accelerator at the downstream of the ISOL. In the ISOL system, two separators are installed to separate a specific RI beam, and control is performed by the Experimental Physics and Industrial Control System (EPICS). In this study, an EPICS IOC (Input-Output Control) was developed to measure the magnetic field of a dipole magnet for mass separation of a multivalent (n+) RI beam in the A/Q separator, which is one of the ISOL RI beam separators. The operational stability of the A/Q separator was tested through a magnetic field measurement using a Hall probe.

A New Program to Design Residual Treatment Trains at Water Treatment Plants (정수장 배출수처리시설 설계 프로그램의 개발)

  • Bae, Byung-Uk;Her, Kuk;Joo, Dae-Sung;Jeong, Yeon-Gu;Kim, Young-Il;Ha, Chang-Won
    • Journal of Korean Society of Environmental Engineers
    • /
    • v.29 no.3
    • /
    • pp.277-282
    • /
    • 2007
  • For more accurate and practical design of the residual treatment train at water treatment plants(WTPs), a computational program based on the commercial spreadsheet, Microsoft Excel, was developed. The computational program for the design of a residual treatment train(DRTT) works in three steps which estimate the residual production to be treated, analyze the mass balance, and determine the size of each unit process. Of particular interest in the DRTT program, is provision for a filter backwash recycle system consisting of surge tank and sedimentation basin for more efficient recycling of backwash water. When the DRTT program was applied to the Chungju WTP, the program was very beneficial in avoiding errors which might have occurred during arithmetic calculations and in reducing the time needed to get the output. It is anticipated that the DRTT program could be used for design of new WTPs as well as the rehabilitation of existing ones.

A Study on the Removal of Ammonia by Using Peat Biofilter (미생물 활성토탄을 이용한 암모니아 제거에 관한 연구)

  • Choung, Youn Kyoo;Ahn, Jun Seong
    • KSCE Journal of Civil and Environmental Engineering Research
    • /
    • v.14 no.3
    • /
    • pp.655-668
    • /
    • 1994
  • Conventional deodorization filters using soil and compost reach the capacity limitation of deodorization in short period, because its removal mechanism primarily depends on adsorption. Therefore, in this study the experiment was performed on the removal of ammonia which is a strong inorganic malodor, frequently emitted from night soil treatment plants and sewage treatment plants, by seeding activated sludges on the bio-peat containing higher organic contents, water conservation capacity, permeability and lower pressure drop. As a result, in raw peat filter natural ammonia outlet was observed in consequence of pH increase resulted from ammonia ionizing in liquid phase. Ammonia removal mechanism primarily depended on the adsorption onto the anion colloidal substances in peat. In peat bio-filter, theoretical ammonium salts ratio was higher than that of raw peat, resulted from slight pH increase by microorganism activity, however, the experimetal value of ammonia-nitrogen accumulated in bio-peat was lower than that of raw peat because of nitrification by nitrifying bacteria. In the initial reaction period, adsorption was predominant in the ammonia removal mechanism, but nitrification was conspicuous after the middle period. Mass balance of nitrogen was established using experimental data of input $NH_3$ loading, output $NH_3$ loading, $NH_4{^+}$-N, $NO_x$-N, and Org-N. The critical time of unsteady state, which is the maximum activating point of microorganism in bio-filter, was determined using experimental data, and the ammonia adsorption curve was computed using regression analysis. On the basis of the results obtained by above analysis, the delay days for the saturation of adsoption capacity in peat bio-filter was calculated.

  • PDF

Introduction of the representative mushroom cultivars and groundbreaking cultivation techniques in Korea

  • Jang, Kab-Yeul;Oh, Youn-Lee;Oh, Minji;Woo, Sung-I;Shin, Pyung-Gyun;Im, Ji-hoow;Kong, Won-Sik
    • Journal of Mushroom
    • /
    • v.14 no.4
    • /
    • pp.136-141
    • /
    • 2016
  • The production scale of mushrooms in Korea is approximately 600 billion won, which is 1.6% of Korea's gross agricultural output. In Korea, ca. 190,000 tons of mushrooms are harvested annually. Although the numbers of mushroom farms and cultivators are constantly decreasing, total mushroom yields are increasing owing to large-scale cultivation facilities and automation. The recent expansion of the well-being trend has caused an increase in mushroom consumption in Korea: the annual per capita mushroom was 3.9 kg ('13), whichis a little higher than that in Europe. Thus, mushroom export, mainly Flammulina velutipes and Pleurotus ostreatus, has increased since the mid-2000s. Recently, however, it is slightly reduced. Nevertheless, Vietnam, Hong Kong, the United States, and the Netherlands continue to export mushrooms, and Korea has increased its export to Australia, Canada, Southeast Asia, etc. Canned Agaricus bisporus, the first export of the Korean mushroom industry, reached it speak sales in 1977-1978. When Korea initiated trade with China in 1980, the international prices of mushrooms fell sharply, leading to shrinkage of the domestic markets. Spurred by the high demand to develop substitute goods for A. bisporus, the oyster mushroom (P. ostreatus) gained attention since it seemed to suit the taste of Korean consumers. Although the log cultivation technique for oyster mushroom was developed in the early 1970s, it required a great deal of labor. Thus, we developed the shelf cultivation technique, which is easier to manage and allows for mass production. In this technique, the growing shelf is made mafrom fermented rice straw, whichis the only P. ostreatus medium in the world and isused only in South Korea. After then, the use of cotton wastes as an additional material of medium, the productivity. Currently, we are developing a standard cultivation technique and environmental control system that can stably produce mushrooms throughout the year. The increase of oyster mushroom production may boostthe domestic market and contribute to industrial development. In addition, oyster mushroom production technology played a role in forming the basis for the development of bottle cultivation, which made mass production. In particular, bottle cultivation using liquid spawn could allow for the export of F. velutipes and Pleurotus eryngii. In addition, the white varieties of F. velutipes were second developed in the world after Japan. We also developed the new A. bisporus cultivar 'Saeah', which is easy to grow in Korea. In hopes to advance the mushroom industry, we will continue to develop cultivars with international competitive power and to improve cultivation techniques.

Development of an Electro Impedance Spectroscopy device for EDLC super capacitor characterization in a mass production line (EDLC 슈퍼 캐피시터 특성 분석을 위한 양산용 전기화학 분석 장치 개발)

  • Park, Chan-Hee;Lee, Hye-In;Kim, Sang-Jung;Lee, Jung-Ho;Kim, Sung-Jin;Lee, Hee-Gwan
    • Journal of the Korea Academia-Industrial cooperation Society
    • /
    • v.13 no.12
    • /
    • pp.5647-5654
    • /
    • 2012
  • In this paper, we developed an electro impedance spectroscopy (EIS) device, which are primarily used for the analysis of fuel cells or batteries, to widen its coverage to the next generation super capacitor EDLC characterization. The developed system was composed of a signal generator that can generate various signal patterns, a potentiostatic generator, and a high speed digital filter for signal processing and measurement program. The developed system is portable, which is not only suitable laboratory use but also for mass production line. The special features of the system include a patterned output signal from 0.01 to 20 kHz, and a fast Fourier transform (FFT) analysis of current signals, both of which are acquired simultaneously. Our tests showed similar results after comparing the analysis from our newly-developed device showing the characteristics of EDLC complex impedance and the analysis from an equivalent impedance which was applied to an equivalent circuit. Now, we can expect a fast inspection time from the application of the present system to the super capacitor production line, based on time-varying changes in electrochemical impedance.

A Study on the Air Vent Valve of the Hydraulic Servo Actuator for Steam Control of Power Plants (발전소의 스팀제어용 유압서보 액추에이터의 공기배출 밸브에 관한 연구)

  • Lee, Yong Bum;Lee, Jong Jik
    • Transactions of the Korean Society of Mechanical Engineers B
    • /
    • v.40 no.6
    • /
    • pp.397-402
    • /
    • 2016
  • To produce adequate electricity in nuclear and thermal power plants, an optimal amount of steam should be supplied to a generator connected to high- and low-pressure steam turbines. A turbine output control device, which is a special steam valve employed to supply or interrupt the steam to the turbine, is operated using a hydraulic servo actuator. In power plants, the performance of servo actuators is degraded by the air generated from the hydraulic system, or causes frequent failures owing to an increase in the wear of the seal. This is due to the seal being burnt as generated heat using the produced compressed air. Some power plants have exhausted air using a fixed orifice, and thus they encounter power loss due to mass flow exhaust. Failures are generated in hydraulic pumps, electric motors, and valves, which are frequently operated. In this study, we perform modeling and analysis of the load-sensing air-exhaust valves, which can be passed through very fine flow under normal use conditions, and exhaust mass flow air at the beginning stage as with existing fixed orifices. Then, we propose a method to prevent failures due to the compressed air, and to ensure the control accuracy of hydraulic servo actuators.

Adaptive Mass-Spring Method for the Synchronization of Dual Deformable Model (듀얼 가변형 모델 동기화를 위한 적응성 질량-스프링 기법)

  • Cho, Jae-Hwan;Park, Jin-Ah
    • Journal of the Korea Computer Graphics Society
    • /
    • v.15 no.3
    • /
    • pp.1-9
    • /
    • 2009
  • Traditional computer simulation uses only traditional input and output devices. With the recent emergence of haptic techniques, which can give users kinetic and tactile feedback, the field of computer simulation is diversifying. In particular, as the virtual-reality-based surgical simulation has been recognized as an effective training tool in medical education, the practical virtual simulation of surgery becomes a stimulating new research area. The surgical simulation framework should represent the realistic properties of human organ for the high immersion of a user interaction with a virtual object. The framework should make proper both haptic and visual feedback for high immersed virtual environment. However, one model may not be suitable to simulate both haptic and visual feedback because the perceptive channels of two feedbacks are different from each other and the system requirements are also different. Therefore, we separated two models to simulate haptic and visual feedback independently but at the same time. We propose an adaptive mass-spring method as a multi-modal simulation technique to synchronize those two separated models and present a framework for a dual model of simulation that can realistically simulate the behavior of the soft, pliable human body, along with haptic feedback from the user's interaction.

  • PDF