• Journal of the Korean Institute of Telematics and Electronics
• /
• v.24 no.5
• /
• pp.786-793
• /
• 1987

This paper describes the design and fabrication of the polysilicon selfaligned bipolar transistor with 1.6\ulcorner epitaxy and SWAMI isolation technologies. This transistor has two levels of polysilicon. Also emitter and adjacent edge of polysilicon base contact of this PSA device are defined by the same mask, and emitter feature size is 2x4 \ulcorner. DC characteristic of the fabricated transistor was evaluated and analyzed for the SPICE input parameters. The minimum propagation delay time per gate of 330 ps at 1mW was obtained with 41 stage CML ring oscillator.

• Transactions on Electrical and Electronic Materials
• /
• v.7 no.4
• /
• pp.173-179
• /
• 2006

Due to the limitations of the channel length, the lateral spread for two-dimensional impurity distributions is critical for the analysis of devices including the integrated complementary metal oxide semiconductor (CMOS) circuits and high frequency semiconductor devices. The developed codes were then compared with the two-dimensional implanted profiles measured by transmission electron microscope (TEM) as well as simulated by a commercial TSUPREM4 for verification purposes. The measured two-dimensional TEM data obtained by chemical etching-method was consistent with the results of the developed analytical model, and it seemed to be more accurate than the results attained by a commercial TSUPREM4. The developed codes can be applied on a wider energy range $(1KeV{\sim}30MeV)$ than a commercial TSUPREM4 of which the maximum energy range cannot exceed 1MeV for the limited doping elements. Moreover, it is not only limited to diffusion process but also can be applied to implantation due to the sloped and nano scale structure of the mask.

• Information and Communications Magazine
• /
• v.24 no.3
• /
• pp.76-86
• /
• 2007

This paper describes the RF performance issues of UE RF Transceiver for W-CDMA system based on 3GPP specifications. the parameters of transmitter and receiver are derived from the viewpoint of RF performance. In order for UE to achieve high performance, the transceiver performance requirements such as ACIR, EVM, Peak Code Domain Error, spectrum emission mask, frequency error stability and TX power control dynamic range for transmitter and reference sensitivity level, blocking characteristics, noise figure, ACS, linearity, AGC dynamic range for receiver are considered. On the basis of the required parameters, the UE RF transceiver is designed and then implemented. The evaluation of RF performance is accomplished through practical test scenarios.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.53-54
• /
• 2007

Charged particle type display using particles which have opposite charge and color is based on effect of reversible optical property due to electric field. we designed mask pattern for fabrication of the charged particle type display based on glass substrate and investigated cell gap dependent of driving voltage and selectively driving method. the panel driven by our selectively driving method, we could obtain image which had vary little crosstalk caused by electrical interference and conform the last image maintained by memory effect without additional voltage.

• Nuclear Engineering and Technology
• /
• v.53 no.4
• /
• pp.1259-1265
• /
• 2021

In the present study, a large-area hybrid gamma imaging system was designed by adopting coded aperture imaging on the basis of a large-area Compton camera to achieve high imaging performance throughout a broad energy range (100-2000 keV). The system consisting of a tungsten coded aperture mask and monolithic NaI(Tl) scintillation detectors was designed through a series of Geant4 Monte Carlo radiation transport simulations, in consideration of both imaging sensitivity and imaging resolution. Then, the performance of the system was predicted by Geant4 Monte Carlo simulations for point sources under various conditions. Our simulation results show that the system provides very high imaging sensitivity (i.e., low values for minimum detectable activity, MDA), thus allowing for imaging of low-activity sources at distances impossible with coded aperture imaging or Compton imaging alone. In addition, the imaging resolution of the system was found to be high (i.e., around 6°) over the broad energy range of 59.5-1330 keV.

• Proceedings of the Korean Society of Computer Information Conference
• /
• 2020.07a
• /
• pp.319-320
• /
• 2020

본 논문에서는 스마트 폰의 GPS 센서와 Google Map, OPEN API 기반의 버스 정보 제공을 하며 연동이 자유로운 어플리케이션을 설계하고 구현한다. 이 어플리케이션은 안드로이드의 GPS센서를 이용하여 현재 사용자의 위치를 기준으로 반경 200m 안의 버스 정류장을 확인할 수 있다. 그리고 공적마스크를 판매하는 약국/농협/우체국의 위치를 확인할 수 있다. 또한, 사용자의 위치 주변이 아닌 곳의 버스와 정류장을 검색할 수 있고 내릴 정류장 혹은 위치를 저장하여 내리기 전 알람을 받을 수 있다.

• Annual Conference of KIPS
• /
• 2021.11a
• /
• pp.177-180
• /
• 2021

코로나바이러스로 인하여 전 세계는 어려움을 겪고 있으며, 바이러스를 확산을 막기 위해서 실외에서는 마스크를 쓰는 것이 일상이 되었다. 하지만, 이를 따르지 않는 사람이 일반 시설에 방문할 때 이를 감지하고 경고를 할 수 있는 시스템이 없어, 마스크 미 착용자로 인한 위험성 방지에 취약점을 가지고 있다. 본 연구에서는 OpenCV 라이브러리를 이용한 마스크 착용 여부를 확인하는 시스템을 설계한다. Haar 특징기반 다단계 분류자를 이용하여 마스크 인식 프로세스를 설계하였으며, 마스크 착용 확인 시스템은 경량 컴퓨터인 라즈베리파이 장치 위에 구현하였다. 또한 확인된 사람의 이미지는 클라우드 시스템에 저장할 수 있도록 구현하였다. 본 연구를 통해, 누구나 손쉽게 해당 마스크 착용 확인 시스템을 중소 매장에 설치하여 사용할 수 있으며, 코로나바이러스 확산 방지에 기여할 수 있다고 예상한다.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2004.08a
• /
• pp.188-190
• /
• 2004

As an effort to reduce cost and lead-time and to increase flexibility and responsiveness, manufacturers are using digital printing in numerous process steps. Typically, these processes require the precise dispensing of various fluids. Piezo ink jet printheads are proving to be reliable tools for depositing active materials such as light emitting polymers (LEP) for mobile phone displays and color filter inks for liquid crystal displays. Ink jets are also being used to provide uniform coatings of polyimide alignment layers and spacers for LCDs. Success with legend printing on PCBs using ink jets has encouraged the design of equipment for directly printing both etch resist and solder mask for PCBs. Development of printers for passive components such as capacitors and resistors is underway. This paper will present the attributes of an ink jet printhead designed to a precision deposition tool and discuss how it is being used to digitally print electronic and flat panel display components. Status of commercialization of digital printing will be discussed along with issues to be resolved before wide adoption takes place.

• 제어로봇시스템학회:학술대회논문집
• /
• 2004.08a
• /
• pp.36-39
• /
• 2004

Electrical impedance tomography (EIT) has been suffered from the severe ill-posedness which is caused by the inherent low sensitivity of boundary measurements to any changes of internal resistivity values. So, small noise occur unexpected reconstruction image. Generally in EIT system, if measured voltage includes noise, we can't find object location and resistivity values. In this paper, we propose digital filter for measured voltage in EIT. Newton-Raphson is the most..popular algorithm in EIT, but noise cause to blur image. We use Fourier transform (FT) in order to minimize the noise and design the filter. After filtering, result of reconstruction image is improved better than before filtering.

• Proceedings of the Korea Institute of Applied Superconductivity and Cryogenics Conference
• /
• 2002.02a
• /
• pp.131-134
• /
• 2002

In this work, we have developed a systematic way of utilizing the basic design tools for superconductive electronics. This include WRSPICE, XIC, margin program, and L-meter. Since the high performance analog-to- digital converter can be built with Rapid Single Flux Quantum (RSFQ) logic circuits the development of superconductive analog-to-digital converter has attracted a lot of interests as one of the most prospective area of the application of Josephson Junction technology. One of the main advantages in using Rapid Single Flux Quantum logic in the analog-to-digital converter is the low voltage output from the Josephson junction switching, and hence the high resolution. To design an 1-bit analog-digital converter, first we have used XIC tool to compose a circuit schematic, and then studied the operational principle of the circuit with WRSPICE tool. Through this process, we obtained the proper circuit diagram of an 1-bit analog-digital converter circuit. Based on this circuit we performed margin calculations of the designed circuits and optimized circuit parameters. The optimized circuit was laid out as a mask drawing. Inductance values of the circuit layout were calculated with L-meter. Circuit inductors were adjusted according to these calculations and the final layout was obtained.