• Journal of Power System Engineering
• /
• 제17권6호
• /
• pp.25-32
• /
• 2013

Biodiesel is technically competitive with it and offers technical advantages over conventional petroleum diesel fuel. Biodiesel is an environment friendly alternative liquid fuel that can be used in any diesel engine without modification. In this study, (dP/dCA)max and heat release, emission characteristics with different fuel injection timings are compared between diesel fuel and biodiesel in the D.I. diesel engine with T/C. The engine was operated at five different fuel injection timings from BTDC 6deg to 14deg at 2deg intervals and with four different loads at engine speed of 1800rpm. The experiments in a test engine showed that ranges between low and high of (dP/dCA)max got narrower, as the engine load increased, BD blend rate increased, and fuel injection timing was delayed. Cumulative heat release increased with the advanced fuel injection timing. NOX emissions decreased with the delays of fuel injection timing.

• Journal of Advanced Marine Engineering and Technology
• /
• 제24권4호
• /
• pp.454-459
• /
• 2000

Diesel engine which has high thermal efficiency is one of the major movers. Recently, as people pay attention to the environmental pollution, the emission of Diesel engine becomes an important problem. So it is needed to understand the characteristics of diesel fuel spray injected into a combustion chamber to reduce the emission. The factors which control the diesel fuel spray are the injection pressure, the nozzle diameter, the impinging angle and the variation of an ambient pressure and temperature. In this paper, the experiments were conducted in the free spray and the impinging spray with various ambient temperatures(273K, 373K, 573K). And the behaviors of the diesel fuel spray, such as penetration, spray angle and axial distance in the free spray and axial distance and spray thickness in the impinging spray were studied.

• Journal of Advanced Marine Engineering and Technology
• /
• 제18권2호
• /
• pp.97-103
• /
• 1994

This paper describes briefly the simulation program for predicting the performance of a high speed turbocharged four cycle diesel engine. The wave phenomena in the intake and exhaust systems are calculated by the characteristic method. The combustion process in the power cycle is represented by the heat release pattern which is given by the Wiebe's function or the pattern based on measured values. Turbocharger matching for the engine is described by utilizing the characteristic maps of both the compressor and turbine, which are obtained from quasi-steady states. A comparison of experimental and calculated results shows a good agreement. Then the influences of the intake system, the period of valve overlap and the characteristics of the turbine are numerically investigated by the simulation.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• 제21권2호
• /
• pp.120-128
• /
• 2011

This paper presents an efficient method to analyze noise and vibration of marine diesel engines mounted on flexible hull structure. The analysis model should in general include the hull structure, leading to lots of computational efforts. To minimize the computational efforts, in this paper, the transfer synthesis utilizing the receptance at the mounting points is proposed. The procedure is then verified by comparing the results with those from the full model calculation. The effects of flexible hull structure on the acoustic power from engine block are finally investigated. It is found that the effect of the hull is significant when the receptance of hull structure is similar to or greater than that of mount or engine block.

• Proceedings of the KIEE Conference
• /
• 대한전기학회 1997년도 하계학술대회 논문집 B
• /
• pp.696-698
• /
• 1997

The marine diesel engine have been widely applied with a mechanical hydraulic governor to control the ship speed for long time. But it was recently very difficult for the mechanical hydraulic governor to control the speed of engine under the condition of low speed and low load because of jiggling by rough fluctuation of rotating torque and hunting by dead time of diesel engine. In order to analyze the speed control system the transfer function was converted from z to w transformation. The author proposed velocity control system with feedback loop by PID controller in order to stabilize for unstable area. The influence of dead time was discussed by Nichols chart and unit step response curve. It was confirmed through computer simulation that the performance improvement of a mechanical hydraulic governor can be obtained by PID controller.

• Journal of Advanced Marine Engineering and Technology
• /
• 제26권2호
• /
• pp.248-255
• /
• 2002

Miller cycle was studied and analyzed by engine performance simulation to achieve very low fuel consumption and to meet the IMO NOx regulation on a medium speed diesel engine. Based on the performance simulation results the intake valve closing time for HYUNDAI HiMSEN 6H21/32 engine was set at 0deg.ABDC(After Bottom Dead Center). Also, the simulation results indicated that significant NOx reduction could be achieved with low reduction of fuel consumption. The performance simulation investigated the effect of compression ratio and turbocharger on fuel consumption and NOx concentration in combination with Miller cycle. The results indicated a significant reduction of fuel consumption with keeping NOx concentration. The results of performance simulation were compared with measured data to verify simulation results. The comparison showed the maximum error was 2.34% in exhaust temperature. Also, the experimental result showed that improvement in BSFC(Brake Specific Fuel Consumption) was 5.8g/kwh with keeping NOx level similar to simulation result.

• Journal of KSNVE
• /
• 제9권5호
• /
• pp.936-942
• /
• 1999

Unstable torsional vibration on the marine ship's propulsion shafting system with diesel engine occurred due to a slippage of multi-friction clutch which was installed between increasing gear and shaft generator. In this paper, the mechanism of this vibration was verified via torsional, whirling, axial and structural vibration measurements of shafting system and noise measurement of gear box. And it was also identified by the theoretical analysis method.

• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 한국마린엔지니어링학회 2005년도 후기학술대회논문집
• /
• pp.21-22
• /
• 2005

A study on the wear characteristics of the white metal(Sn-base alloy) bearing as a function of particle contamination level was conducted in order to establish control criteria of the lubricant in the 2-stroke marine diesel engine. Particle contamination level of the lubricants ranged from NAS 10 to 12 for the experiments. Bar-on-plate type wear test was performed using reciprocating wear tester. Based on this study it was found that there was no noticeable difference in weight loss of the white metal for NAS10 and NAS11(particle contamination level). Surface roughness of the white metal bearing after the wear test of 8hrs for the highly contaminated lubricant(NAS12 level) was up to $6{\mu}m$ in Rmax whilst that of the less contaminated lubricants(NAS10 & 11) was less than $1.5{\mu}m$ in Rmax.

• Journal of Advanced Marine Engineering and Technology
• /
• 제18권5호
• /
• pp.56-67
• /
• 1994

The installation methods of diesel engines in ships would be largely classified into two groups : one is the direct mounting system fixing engine directly into double bottom of the hull, and the other is the resilient mounting system having vibration absorbers between engine and ship body such as rubber plate to prevent shocks or vibration transmission. The direct mounting system is generally used for large-sized low speed diesel engines, because the resilient mounting system has difficulties in reducing the natural frequency of engine itself under normal speed. On the contrary, the resilient mounting system is often used for medium or high speed engines for marine propulsion and generator that have light weight and high revolution speed. Recently, it is even applied to engines having relatively low speed(300-400rpm) for fishing boats. Although many researches for the resilient mounting system have been carried out, many problems in applying these results directly to marine vessels because most of these have been used for automobiles. Up to now we have had to depend on the professional foreign company in design and the supply of parts for the resilient mounting system of marinediesel engines utterly. In preseut study, the exciting forces of engines effecting to resilient mounting were examined, and patterns of vibration and evaluation procedure for force transmission from resilient mounting to the body of hull were established. Also, these results were applied to the analysis of free and forced vibration for the rubber-type resilient mounting systems of marine diesel engines. Besides, after changing the various design parameters, such as locations, angles, dynamic characteristics and the number of resilient mountings, the influences on resilient mounting system were also examined.

• Journal of Advanced Marine Engineering and Technology
• /
• 제38권6호
• /
• pp.744-750
• /
• 2014

The monitoring and abnormality warning of marine diesel engine are important to take appropriate responses for safety navigation. If maintenance engineers do not take appropriate response because of diagnosis mistakes, it will occur a nasty accident. Therefore, we need integrated monitoring and diagnosis system for supporting a diagnosis objectively. In this paper, we analyze time-series data which measured by real-time, monitor the changing of conditions and trends of the analyzed data. Furthermore, we design and implement a monitoring and diagnosis system for objective supporting of real-time diagnosis. When the integrated monitoring and diagnosis system is adopted, it can help to improve stability of marine diesel engine by providing abnormality warning alarm with appropriate responses.