• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2006.06a
• /
• pp.27-28
• /
• 2006

최근 LNG 연료 시장의 호황에 힘입어 LNG선들이 점차 대형화 추세에 있고, LNG선의 추진 기관 또한 경제성, 환경 영향 등의 주어진 요구 환경에 따라 다양화 되고 있다. 기존의 Steam Turbine Propulsion 외에 Conventional 2-stroke Diesel Engine 및 Dual-fuel 4-stroke Diesel Engine of LNG선의 주 기관으로서 이미 상용화 되었고, 기술적/경제적인 이유로 일반 상선의 주기관으로서는 논외에 있었던 Gas Turbine 또한 일부 Oil Major와 Gas Turbine Maker에 의해 그 적용 가능성이 논의되고 있다. 이에 따라 LNG 선에 Gas Turbine 적용 타당성, 고려 사항 및 적용에 따른 이점과 단점 등을 고찰하였다.

• Corrosion Science and Technology
• /
• v.13 no.1
• /
• pp.28-35
• /
• 2014

Recently, the fuel oil of diesel engines of marine ships has been increasingly changed to heavy oil of low quality as the oil price is getting higher and higher. Therefore, the spiral gear attached at the motor of the oil purifier which plays an important role to purify the heavy oil is also easy to expose at severe environmental condition due to the purification of the heavy oil in higher temperature. Thus, the material of the spiral gear requires a better mechanical strength, wear and corrosion resistance. In this study, the heat treatment(tempering) with various holding time at temperature of $500^{\circ}C$ was carried out to the alloy of Cu-7Al-2.5Si as centrifugal casting, and the properties of both hardness and corrosion resistance with and without heat treatment were investigated with observation of the microstructure and with electrochemical methods, such as measurement of corrosion potential, cathodic and anodic polarization curves, cyclic voltammogram, and a.c. impedance. in natural seawater solution. The ${\alpha}$, ${\beta}^{\prime}$ and ${\gamma}_2$ phases were observed in the material in spite of no heat treatment due to quenching effect of a spin mold. However, their phases, that is, ${\beta}^{\prime}$ and ${\gamma}_2$ phases decreased gradually with increasing the holding time at a constant temperature of $500^{\circ}C$. The hardness more or less decreased with heat treatment, however its corrosion resistance was improved with the heat treatment. Furthermore, the longer holding time, the better corrosion resistance. In addition, when the holding time was 48hrs, its corrosion current density showed the lowest value. The pattern of corroded surface was nearly similar to that of the pitting corrosion, and this morphology was greatly observed in the case of no heat treatment. It is considered that ${\gamma}_2$ phase at the grain boundary was corroded preferentially as an anode. However, the pattern of general corrosion exhibited increasingly due to decreasing the ${\gamma}_2$ phase with heat treatment. Consequently, it is suggested that the corrosion resistance of Cu-7Al-2.5Si alloy can be improved with the heat treatment as a holding time for 48 hrs at $500^{\circ}C$.

• Journal of Navigation and Port Research
• /
• v.48 no.2
• /
• pp.125-136
• /
• 2024

This research presents an innovative integrated ethanol solid oxide fuel cell (SOFC) system designed for applications in marine vessels. The system incorporates an exhaust gas heat recovery mechanism. The high-temperature exhaust gas produced by the SOFC is efficiently recovered through a sequential process involving a gas turbine (GT), a regenerative system, steam Rankine cycles, and a waste heat boiler (WHB). A comprehensive thermodynamic analysis of this integrated SOFC-GT-SRC-WHB system was performed. A simulation of this proposed system was conducted using Aspen Hysys V12.1, and a genetic algorithm was employed to optimize the system parameters. Thermodynamic equations based on the first and second laws of thermodynamics were utilized to assess the system's performance. Additionally, the exergy destruction within the crucial system components was examined. The system is projected to achieve an energy efficiency of 58.44% and an exergy efficiency of 29.43%. Notably, the integrated high-temperature exhaust gas recovery systems contribute significantly, generating 1129.1 kW, which accounts for 22.9% of the total power generated. Furthermore, the waste heat boiler was designed to produce 900.8 kg/h of superheated vapor at 170 ℃ and 405 kP a, serving various onboard ship purposes, such as heating fuel oil and accommodations for seafarers and equipment.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.30 no.1
• /
• pp.58-64
• /
• 2024

Approximately 250 marine oil spill accidents have occurred in Korea, with profound impact on local communities and the environment. The restoration process necessitates significant resources and costs to return affected areas to their pre-accident state. In accordance with the polluter pays principle, compensation is demanded from polluter, as stipulated in both international conventions and national laws. Consequently, investigations are conducted to determine civil and criminal liability. As the importance of investigation actors in oil spill accidents increases, standards such as CEN 15522-2 and ASTM D 3248 are employed to determine the similarity between the spilled oil and the oil of the suspected ship. Among these standards, CEN 15522-2, the most actively used European standard, underwent its third revision and is now known as EN 15522-2, as of 2023. This study used EN 15522-2 to analyze samples from marine oil spill accidents that occurred in Korea. The results indicated that, considering the characteristics of domestic spills where light fuel oil spills account for more than 40%, the application of EN 15522-2, which includes low-boiling point substances such as Adamantanes, was confirmed to be highly effective.

• Journal of Advanced Marine Engineering and Technology
• /
• v.39 no.7
• /
• pp.716-721
• /
• 2015

As the severity of environmental pollution has increased, restrictions on air pollution have been strengthened. Stringent regulations have been imposed, not only on marine diesel engines but also on automotive and industrial power plants. Thus, biofuels have been directly applied in practical engines and used in training ships for basic research. Even though a high biofuel percentage cannot be used in a training ship engine for safety reasons, because this type of engine is larger than those used in institutional laboratories, the results will provide important basic information that will allow organizations to determine the status of a large output. Biodiesel fuel was studied to determine how it would affect the combustion characteristics and exhaust emissions of a marine diesel generator engine. The main results can be summarized as follows. Because the physical and chemical compositions of biofuels are similar to those of diesel fuel, it was found that their practical use was possible in a training ship. The specific fuel consumption and NOx increased, whereas a tendency was found for carbon monoxide and soot to decrease. In addition, no significant pressure change difference was found between the diesel fuel and biofuels.

• Proceedings of KOSOMES biannual meeting
• /
• 2007.11a
• /
• pp.133-137
• /
• 2007

An experimental study is conducted to evaluate and compare the use of BiodieseDI Fuel supplements at blend ratio of 10/90(BDF10) and 20/80(BDF20), in four stroke, direct injection diesel engine located at the authors' laboratory. especially this Biodiesel is produced from Rape oil at the authors' laboratory. The tests are conducted using each of the above fuel blends, in the engine working at a speed of 1800rpm and at a various loads. In each test, specific fuel consumption, exhaust emissions such as nitrogen oxides(NOx), carbon monoxide(CO) and Soot are measured. The results of investigation at various operating conditions are as follows (1) Specific fuel consumption is increased average 1.52%, maximum 1.84% at load 25% in case of BDF10, and average 1.98%, maximum 2.80% at load 25% in case of BDF20. (2) CO emission is decreased average 5.14%, maximum 6.09% at load 0% in case of BDF10, and average 7.75%, maximum 9.13% at load 0% in case of BDF 20. (3) NOx emission is increased average 2.97%, maximum 3.74% at load 0% in case of BDF10, and average 3.84%, maximum 4.67% at load 0% in case of BDF20. (4) Soot emission is decreased average 9.36%, maximum 10.85% at load 75% in case of BDF10, and average 11.99%, maximum 13.95% at load 75% in case of BDF20.

• Journal of Advanced Marine Engineering and Technology
• /
• v.35 no.1
• /
• pp.53-59
• /
• 2011

The using of diesel engine will be increased in the world for fuel economy. But diesel engine emits harmful emissions such as much NOx, smoke etc. In this study, experiments were performed to investigate the spray characteristics of diesel spray in a common-rail system according to fuel temperature, injection pressure, injection period and fuel viscosity etc. using a high speed video camera. Diesel oil has different spray patten due to injection pressure and injection period in a common-rail system. A Filter pressure was influenced by fuel temperature which was turned to fuel viscosity related to a fluid flowing. The effect of the bio-diesel fuel mixing ratio on the spray and atomization characteristics was also investigated at various experimental conditions. It shows that the droplet atomization characteristics of bio-diesel fuel showed deteriorated results as the mixing ratio of biodiesel increased because of the high viscosity.

• Journal of Advanced Marine Engineering and Technology
• /
• v.38 no.9
• /
• pp.1064-1069
• /
• 2014

The use of emulsified fuel and EGR (Exhaust gas recirculation) system are effective methods to reduce NOx emission from diesel engines. In general, it is considered that EGR method influences diesel engine combustion in three different ways: thermal, chemical and dilution effect. Among others, the thermal effect is related to the increase of specific heat capacity due to the presence of $CO_2$ and $H_2O$ in inlet air. Meanwhile, emulsified fuel method of utilizing latent heat of vaporization and miro-explosion has been recognized as an effective technique for reducing diesel engine emissions. In this paper, an author studied on combustion and emission characteristics by using emulsified fuel (EF, Light oil : 80% + Water : 20%) and EGR (30% EGR ratio) system. And the effect of fuel injection pattern control was investigated.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.25 no.3
• /
• pp.269-277
• /
• 2019

Since 2020, according to the International Convention for the Prevention of Pollution from Ships (MARPOL) amended in 2016, each Administration shall transfer the annual fuel consumption of its registered ships of 5,000 gross tonnage and above to the International Maritime Organization (IMO) after verifying them. The Administration needs stacks of materials, which must not be manipulated by ship companies, including the Engine log book and also bears an administrative burden to verify them by May every year. This study considers using the Automatic Identification System (AIS), mandatory navigational equipment, as an objective and efficient tool among several verification methods. Calculating fuel consumption using a ship's speed in AIS information based on the theory of a relationship between ship speed and fuel consumption was reported in several examples of relevant literature. After pre-filtering by excluding AIS records which had speed errors from the raw data of five domestic cargo vessels, fuel consumptions calculated using Excel software were compared to actual bunker consumptions presented by ship companies. The former consumptions ranged from 96 to 123 percent of the actual bunker consumptions. The difference between two consumptions could be narrowed to within 20 percent if the fuel consumptions for boilers were deducted from the actual bunker consumption. Although further study should be carried out for more accurate calculation methods depending on the burning efficiency of the engine, the propulsion efficiency of the ship, displacement and sea conditions, this method of calculating annual fuel consumption according to the difference between two consumptions is considered to be one of the most useful tools to verify bunker consumption.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.14 no.4
• /
• pp.280-286
• /
• 2011

In this research, the oil detection method and the characteristic of sensor using the selective reaction of silicone rubber in response to hydrocarbon oil will be described. As a sensing principle, the swelling property of silicone rubber in response to hydrocarbon fuel is used, also a strain gauge is used to transduce the volume change to an electrical signal. The sensor core is manufactured with a strain gauge embedded in silicone rubber by the curing process and experiments for characteristics of sensor core with various oils were carried out. It is shown that the sensor core can be used as an oil spill detection sensor. Also, for the application to the sea area, a buoy type sensor platform is integrated with a sensor core and a strain amplifier and it is tested in the simulated oil spill condition. In this study, it is proven that the integrated sensor can be used for the detection of various oils.