• Proceedings of the KIEE Conference
• /
• 2001.07c
• /
• pp.1798-1800
• /
• 2001

As a batch Type device, this machine is contrive to seal glass plates for plasma BLU (Back Light Unit) by indirect heating from electric heaters. In order to maintain the heating / cooling Chambers clean, this machine uses a muffle formation. The components of the machine are listed bellow.

• 제어로봇시스템학회:학술대회논문집
• /
• 2002.10a
• /
• pp.70.2-70
• /
• 2002

In the thermal power plant, it is difficult to maintain strict control of the steam temperature in order to avoid thermal stress, because of variation of the heating value according to the fuel source, the time delay of changes in main steam temperature versus changes in fuel flow rate, difficulty of control on the main steam temperature control and the reheater steam temperature control system owing to the dynamic response characteristics of changes in steam temperature and the reheater steam temperature, fluctuation of inner fluid water and steam flow rates widely during load-following operation. Up to the present time, the PID controller has been used to operate this system...

• 제어로봇시스템학회:학술대회논문집
• /
• 1988.10a
• /
• pp.289-294
• /
• 1988

This paper describes tbe design and implementation of the adaptive controller to maintain the glood weld quality in gas metal arc welding process. The weld torch travel speed and the surface temperature are taken, respectively, as an input and an output of the welding control system. Because of the very complex phenomena of the process, the input-output dynamic model was experimentally identified by AIC (Akiake Information Criterion). Based on the model structure, the explicit model reference adaptive controller is simulated in order to regulate the output tempernture to the desired level.

• 제어로봇시스템학회:학술대회논문집
• /
• 1988.10a
• /
• pp.103-108
• /
• 1988

A walking robot must have the ability to change the body direction in order to avoid the obstacles. In this paper, we develop a gait control algorithm that can maintain the stable movement of the robot for three different modes of changing directions. The algorithm makes it possible for the robot to have the larger gait stability margin than the threshold value by the method of changing the body speed.

• Proceedings of the Korean Operations and Management Science Society Conference
• /
• 1996.10a
• /
• pp.57-60
• /
• 1996

It is critical that all companies improve productivity in order to maintain their international competitiveness. The productivity can be explained as a measurement of effectiveness that is calculated by "the ratio of what is produced to what is required to produce it". The goal of this paper is to enhance productivity for a small fast food company mainly through work analysis. This work analysis will help the company to downsize by improving efficiency via motion analysis and by reduction of losses via facility improvement.provement.

• Journal of the Korean Society of Costume
• /
• v.14
• /
• pp.75-85
• /
• 1990

The dress and personal adorments of Chi Li in Li Chi was investigated in this study. The summary of this study is as follows: It was found that the ancient Chinese used their dress and personal adornments as an important means of maintaining or establishing harmony with the universe, supernaturals, and human beings. It also appeared that dress was used to control man's psychology and to maintain social order. Differentiation of person's social status and position was made by using dress and personal adornments. Ceremonial costume such as mourning appeared considerably in Chi Li.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.11a
• /
• pp.342.2-342
• /
• 2002

Fault tolerant control algorithm fer heteropolar magnetic bearings are presented. This fault tolerant control utilizes grouping of currents as C-cores in order to isolate magnetic fluxes. Hardware requirements to maintain fault tolerant control are reduced since decoupling chokes are not required in this control scheme. The currents supplied to each pole are redistributed, if some coils (ail suddenly, such that the resultant magnetic forces should remain invariant through coil failure events. (omitted)

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2004.08a
• /
• pp.268-276
• /
• 2004

As recent demands for cold rolling oil for steel, not only better lubricity, but cost reduction and improvement of work environment are increasingly required. In order to respond these demands, Nihon Parkerizing has developed rolling oils with completely new emulsification system. Comparing with conventional oils, the new system indicates better iron fine removability to maintain oil concentration, due to better iron fine dispersion, and superior mill stain resistance by spray stain test.

• Proceedings of the KIEE Conference
• /
• 2008.07a
• /
• pp.1829-1830
• /
• 2008

The paper deals with leader-follower formations of nonholonomic mobile robots using least square method in order to maintain the formation constantly. The nonholonomic property of the mobile robot cause us to use the least square method. Then, the performance of the developed formation controller is verified by simulation results.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2002.08a
• /
• pp.24-27
• /
• 2002

Even though the TFT-LCD industry gained enough momentum that has been built up in past 10 years, the industry faces new challenges in order to maintain the 'true mainstream display' position in near future. The technical challenges can be summarized in two fold; one is image quality upgrade for different application area. Cost competitiveness is the other big issue in LCD for the continued leadership position in display industry. In this paper, we describe the technology advancement and the technical challenges in LCD to achieve these goals..