• 한국분무공학회지
• /
• 제21권2호
• /
• pp.95-103
• /
• 2016

The effect of pilot injection quantity on the combustion and emissions characteristics of a compression ignition engine with a biodiesel-compressed natural gas (CNG) dual fuel combustion (DFC) system is studied in this work. Biodiesel is used as a pilot injection fuel to ignite the main fuel, CNG of DFC. The pilot injection quantity is controlled to investigate the characteristics of combustion and exhaust emissions in a single cylinder diesel engine. The injection pressure and injection timing of pilot fuel are maintained at approximately 120 MPa and BTDC 17 crank angle, respectively. Results show that the indicated mean effective pressure (IMEP) of biodiesel-CNG DFC mode is similar to that of diesel-CNG DFC mode at all load conditions. Combustion stability of biodiesel-CNG DFC mode decreased with increase of engine load, but no notable trend of cycle-to-cycle variations with increase of pilot injection quantity is discovered. The combustion of biodiesel-CNG begins at a retarded crank angle compared to that of diesel-CNG at low load, but it is advanced at high loads. Smoke and NOx of biodiesel-CNG are simultaneously increased with the increase of pilot fuel quantity. Compared to the diesel-CNG DFC, however, smoke and NOx emissions are slightly reduced over all operating conditions. Biodiesel-CNG DFC yields higher $CO_2$ emissions compared to diesel-CNG DFC over all engine conditions. CO and HC emissions for biodiesel-CNG DFC is decreased with the increase of pilot injection quantity.

• 한국추진공학회지
• /
• 제16권1호
• /
• pp.36-44
• /
• 2012

친환경 추진제인 고농도 과산화수소와 케로신을 추진제로 사용하는 다중 분사기 액체 로켓 엔진을 설계하였다. 엔진의 설계 요구 조건을 결정한 후 엔진의 주요 형상 치수를 이론적인 배경을 통하여 결정하였다. 다중 분사기는 6개의 분사기를 장착하였으며, 상용 해석 툴을 이용하여 과산화수소 매니폴드 내의 유동 해석을 수행하여 매니폴드 내에서 균일한 유량분포 및 냉각성능 확보를 위해 유동 정체 구간과 재순환 영역을 최소화하였다. 매니폴드 유동장 해석 결과를 바탕으로 유동이 최적화 되는 다중 분사기를 제작하였으며, 수류 실험을 통하여 추진제의 유량, 분무각 및 분무 성능을 확인하였다.

• 한국세라믹학회지
• /
• 제34권1호
• /
• pp.88-94
• /
• 1997

플라즈마 용사법(plasma spray method)으로 제작된 상용 가스 터빈 연소기의 finned segment의 열차폐용 코팅계, ZrO2-8wt%Y2O3 top coat/Ni-26Cr-5Al-0.5Y bond coat/Hastelloy X superalloy 기판에서 NiCrAlY bond coat의 산화 거동과 열피로 파괴에 대하여 조사하였다. 생성된 bond coat의 주산화물은 NiO, CrO2, Al2O3였다. ZrO2/bond coat계면에서 생성된 산화물의 분포는 고온에서의 사용 전에 이 계면 아래에 얇은 층의 Al2O3가없는 곳에서는 NiO 산화층 및에 Cr2O3와 Al2O3가 혼합된 형태를 나타내었다. 열피로에 의해 박리된 시편의 파면을 관찰한 결과, 파괴는 주로 ZrO2/산화층 계면보다 세라믹층내로 약간 치우쳐서 일어나지만, 산화층 내에서도 약간 일어남을 알 수 있었다.

• 대한기계학회논문집
• /
• 제9권5호
• /
• pp.627-637
• /
• 1985

본 논문에서는 종래의 방법을 개량해서 연소과정의 휘도변화를 전기적신호로 변환시키고, 이 전기신호와 연료분사개시기에 발생하는 전기신호와의 시간차를 시간 간격측정기에 의해 계측하는 방법을 택했다. 이 방법에 의해 측정하고저 하는 온도 또는 연료의 종류별로 매 1,000개의 시간차 데이터를 퍼스널.컴퓨터(personal compu- ter)에 기억시켜 통계처리했다.그리고 착화지연기간의 측정결과에 대해서는 보조연 료로서 사용한 유기화합물의 반응성으로 부터 고찰했다.

• KIEAE Journal
• /
• 제7권1호
• /
• pp.33-40
• /
• 2007

0.4 Million tons of shell powder have been disused as waste in KOREA and caused severe environmental pollution though shell powder can be utilized in real life for many ways. It is impending problem to recycle shell powder as it requires high expense for burying and temporary outside heap and causes severe environmental pollution being a main factor of ocean waste. To suggest the basic data for development of eco-friendly and high-function Wall Coatings Thin Textured Finishes, a wall coating sample was applied to indoor walls of a mock-up and temperature and humidity were measured to assess the thermal performance of it, and a survey of preference for the color sense and feel of the materials with a movie of specimens. The results of the study are following; 1) High insulation performance is shown from the assessment result of the room polystyrene board adhered on the walls then high humidity controlling performance is shown from that of the room polystyrene board coated by shell powder. This point out that shell powder has superiority for humidity controlling. 2) The result of thermal and humidity assessment shows that shell powder makes up for thermal conduction of the polystyrene board and same result can be expected from the assessment with materials which has similar thermal characteristics with polystyrene.3) Ranking of preferred specimens is; 1st Case 13, 2nd Case 17, 3rd Case 16, and 4th Case 12. Preferred shell powder was the ark shell. Preferred powder for plaster was the powder mixed with that sifted by 0.8mm, 100mesh and 40mesh, and for spray was the fine powder mixed with that sifted by 100mesh and 40mesh.

• Journal of Biosystems Engineering
• /
• 제31권3호
• /
• pp.153-160
• /
• 2006

This study was performed to evaluate some geometrical characteristics of disc type swirl nozzles and to develop nozzles having improved spraying performance for knapsack sprayers. Considered geometrical characteristics of the nozzles were disc thickness, orifice diameter, swirl chamber diameter and shape of the swirl chamber (nozzle chamber). 3 types of nozzle cores were compared. Main results of this study were as follows. 1. Spraying angle (A) was increased with decreasing disc thickness (x), and with increasing orifice diameter (y) or spraying pressure (z). The equation was as a follow. $$A=3.95\frac{1}{x}+73.50\sqrt{y}+18.97\sqrt{z}-60.16$$ 2. Spraying flow rate (F) was increased with decreasing disc thickness (x), and with increasing orifice diameter (y) or spraying pressure (z). The equation was as a follow. $$F=-89.95x+611.09y+620.49\sqrt{z}-868.20$$ 3. Mean spraying droplet size (V) was decreased with decreasing disc thickness (x), with increasing orifice diameter (y) in low spraying pressure, with decreasing orifice diameter (y) in high spraying pressure, and with increasing spraying pressure (z). $$V=148.77x^4-746.85x^3+1311.76x^2-917.31x$$ 4. The spray pattern was compared using CV values. The CV value of the nozzle core type 1 was 26.7% in spraying pressure $3\;kgf/cm^2$, the CV value of the core type 2 was 23.6% in spraying pressure $2\;kgf/cm^2$, the CV value of the core type 3 was 20.6% in spraying pressure $1\;kgf/cm^2$. 5. Minimum spraying pressure was improved from $1.5\;kgf/cm^2\;to\;1.0\;kgf/cm^2$ by changes of nozzle core shape.

• 한국구조물진단유지관리공학회 논문집
• /
• 제18권5호
• /
• pp.51-58
• /
• 2014

본 연구에서는 철근콘크리트 구조의 FRP를 이용한 보강에서 낮은 내화성능을 개선하기 위한 방안을 찾기 위하여, 보강된 FRP의 외부를 내화보강하는 방법에 대한 내화실험을 실시하였다. 특히 철근콘크리트 부재의 피복에 홈을 형성하여 FRP를 매입하는 보강 즉, NSM 보강을 대상으로 하였다. 실험에서의 주요 변수는 보강방법과 사용 내화재료로서, Perlite계 재료를 표면에 분사하여 보강하는 방법, Calcium silicate계 보드로 표면에 부착하는 방법, 그리고 추가로 홈내부에 Polymer mortar 또는 Calcium silicate조각을 삽입하여 보강하는 방법으로 보강한 뒤 가열로 내부의 온도변화에 따른 열전달을 관찰하였다. 실험결과, Perlite계 내화뿜칠로 표면을 보강하는 경우보다 Calcium Silicate계 내화보드로 표면을 보강하는 방법이 효과적인 것으로 나타났다. 홈 내부의 에폭시가 유리전이온도에 도달할 때의 외부 표면온도 $820^{\circ}C$까지 내화단열성능을 확보할 수 있는 것으로 나타났다.

• 한국자동차공학회논문집
• /
• 제15권4호
• /
• pp.10-16
• /
• 2007

A rubber seal for wheel bearing which has been mainly applied to car wheel supporting device is required to have both high sealing performance and drag torque. Because of severe operational conditions like infiltration of mud or splashed water, the importance of rubber seal which is aimed for leakage prevention of grease and effective blocking of foreign substances has been increasing continuously. The sealing performance of this seal depends on several factors such as materials of seal, friction conditions of contact regions and geometry of seals and so on. We have focused on the effects of geometric characteristics such as the angle of main lip, interference between lip edge and inner metallic ring. In this study, the optimization of geometric variables was performed using the finite element analysis. For the sake of finite element analysis, uniaxial tensile tests were conducted and several constants for Mooney-Rivlin's equation were obtained. According to the results of this study, mock-up bearing was made. To verify this study, drag torque and mud spray test were preformed.

• Food Science and Biotechnology
• /
• 제18권1호
• /
• pp.113-117
• /
• 2009

A method was developed using enhanced liquid chromatography coupled with electrospray ionization mass spectrometry for the analysis and quantitation of 2 main potato glycoalkaloids, $\alpha$-chaconine, and $\alpha$-solanine, without any pre-concentration or derivatisation steps. Calibration curves generated by this technique exhibited a linear dynamic range from 0.025 to $50{\mu}g/mL$ and from 0.05 to $50{\mu}g/mL$ for $\alpha$-chaconine and $\alpha$-solanine, respectively. Matrix effects were evaluated by comparing calibration curves measured in matrix-matched and solvent-based systems. Ion suppression due to matrix effects was weak and extraction recoveries of 88 to 114% were obtained in different sample matrices spiked with analyte concentrations ranging from 15 to $35{\mu}g/mL$. Potatoes that had been genetically modified to tolerate glufosinate contained the same glycoalkaloid levels as their non-transgenic counterpart. We suggest complementing compositional comparison assessment strategy by validating quantitative analytical methods for the toxic glycoalkaloids in potato plants.

• Food Science and Biotechnology
• /
• 제18권6호
• /
• pp.1470-1475
• /
• 2009

The seed coat of the black soybean contains 3 main anthocyanins such as delphinidin-3-O-$\beta$-glucoside, cyanidin-3-O-$\beta$-glucoside, and petunidin-3-O-$\beta$-glucoside. As a part of our effort on discovering and breeding new black soybean cultivars which possesses specific anthocyanin component rich, we determined the anthocyanin profiles of the 2 cultivars recently developed soybean cv. Gaechuck #1 and cv. Gyeongsang #1, using liquid chromatography-tandem mass spectrometry (LC-MS/MS) and compared their content and identity with those of previously known 10 cultivar controls. The Cosmosil-$5C_{18}$-AR-II column were selected for the analysis because of the best peak separation. The column temperature was set up at $35^{\circ}C$. The mobile phase consisting of water containing 0.5%(v/v) formic acid and methanol gave good separation between the 3 anthocyanin analytes and internal standard (quercetin 3-O-$\beta$-rutinoside) and peaks with suppressed tail. The MS/MS spectra of each individual anthocyanin standard were detected in positive electron spray ionization (ESI) modes. It was disclosed that the anthocyanin contents of the soybean cv. Gaechuck#1 and cv. Gyeongsang#1 are roughly higher than those of the 10 controls.