• 대한기계학회논문집A
• /
• 제37권4호
• /
• pp.511-519
• /
• 2013

능동 자기베어링의 바이어스 선형화 방법은 자기베어링의 동역학적 성능과 선형성을 확보하지만, 바이어스 전류에 의한 상시 소모전력이 발생하여 시스템의 효율이 저하된다. 반면, 스위칭 제어기는 바이어스 전류를 사용하지 않아 베어링의 소비 전력을 최소화할 수 있다. 본 논문에서는 능동 자기베어링 시스템에 적용되는 스위칭 제어기와 동기 노치필터를 포함하는 비례-미분 제어기의 성능을 비교하였다. 공정하고 객관적인 비교를 위해 기준제어기인 동기 노치필터 제어기를 합리적으로 설계하고, 스위칭 제어기가 기준제어기와 동일한 동역학 특성을 갖도록 하였다. 회전축의 굽힘 유연모드 및 센서와 증폭기의 특성을 포함하는 시스템의 동역학 모델을 수립하고 성능 비교 지표를 수립하였다. 불평형 질량에 응답 측면에서 제어기를 비교하여, 저속 영역에서 스위칭 제어기가 기준제어기 대비 10 배 이상 동손을 저감할 수 있으나, 회전축의 굽힘 유연모드와 일치하는 회전 속도 근방에서는 스위칭 제어기가 유효하지 않음을 확인하였다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1995년도 추계학술대회 논문집
• /
• pp.769-772
• /
• 1995

Most turbo machines, which operate at high speeds, such as gas turbines, jet engines, pumps, and compressors are prone to perrturbing vibrations. The best vibration control method for rotors is to eliminate destabilizing factors. Careful balancing application of "more stable" oil-lubricated bearing, such as tilting pad bearings or use of anti-swirl devices in seals, are examplse of passive vibration control methods. the use of magnetic bearing is an active control method. An obvious advantage of active control is that it provides damping (or modifies system stiffness or other parameters) only when there is a need for that, i.e., in emergency states, while not affecting the rotor normal operational conditions. Moreover, active control methods provide exact position control through on-line control. In this study, a magnetic actuator, digital contrliier using DSP, and bipolar operational power supply/amplifiers were developed to show the effectiveness of reducing robot vibration. Also the curve fitting procedure to obtain the transfer function of frequency dependent component was developed. Results presented in this dissertation will provide a well-defined technical parameters in designing magnetic damper system.er system.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2001년도 춘계학술대회 논문집
• /
• pp.505-509
• /
• 2001

When the spindle is rotated for machining the workpiece, the vibration is generated due to the spindle unbalance. This vibration affects surface finish, dimensional accuracy, tool life, and spindle bearings. To compensate this effect of the spindle unbalance, the spindle system using an EME(electro magnetic exciter)is proposed in this paper. In the proposed spindle system, the vibration due to the spindle unbalance is monitored using vibration sensors and is compensated by electromagnetic attractive forces generated in the EME which are excited by anti-direction forces corresponded with the measured unbalance. Firstly, the spindle system using an EME and control system are constructed to compensate the effect of spindle unbalance in this paper. And then the system is modeled by bond graph to analyze the system. Finally, a controller for vibration compensation due to spindle unbalance is designed and is implemented in real experimental system. As a result, experimental results show this proposed spindle system is very effective to compensate the spindle unbalance.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2008년도 춘계학술대회논문집
• /
• pp.290-293
• /
• 2008

This paper proposes a criterion to select the modes for modal truncated model of flexible rotor only supported by active magnetic bearings. The proposed approach relies on the concepts of minimum control input and output energy assuming that the system is subjected to transient disturbances. Accurate large order model for the levitated rotor is taken by finite element analysis and transformed to the modal equation. By proposed methodology, which modal states should be retained in the truncated model are investigated over the whole operational speed range by the calculation. Finally, the effectiveness is verified by checking the model error between original model and reduced model.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 추계학술대회 논문집
• /
• pp.52-55
• /
• 1997

In this paper, the case study of reducing rotational errors is done for a grinding spindle with an active magnetic bearing system. The rotational errors acting on the magnetic bearing spindle are due to mass unbalance of rotor, runout, grinding excitation and unmodeled nonlinear dynamics of electromagnets. For the most case, the electrical runout of sensor target is big even in well-finished surface; this runout can cause a rotation error amplified by feedback control system. The adaptive feedforward method based on LMS algorithm is discussed to compensate this kind of runout effects, and investigated its effectiveness by numerical simulation and experimental analysis. The rotor orbit size in both bearings is reduced about to 5 pin due to lX rejection by feedforward control up to 50, 000 rpm.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집B
• /
• pp.36-41
• /
• 2001

The performance of an inductive position sensor is described by the accuracy and the dynamic characteristics of the sensor. Both of these performance indices are affected by magnetic hysteresis and eddy currents. In this paper, a model of an inductive sensor is presented. This model includes the effects of hysteresis and eddy currents. Computer simulation shows that the sensitivity of the sensor is greatly affected by hysteresis and eddy currents. Repeability error increases with hysteresis and eddy currents effects. Results also show that eddy currents influence more on the sensor performance than hysteresis does. To reduce the effects of hysteresis and eddy currents, the sensor should be made out of thin laminations with high resistivity.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2004년도 하계학술대회 논문집 B
• /
• pp.827-829
• /
• 2004

A characteristic of the rotating machine that has been receiving relatively little attention is the axial force on the rotor versus its axial displacement from magnetic neutral position. A knowledge of this force is essential to the economic application of thrust bearings for rotating machine and their connected loads. In this paper this axial force is analyzed and calculated and test values are verified with two different machines.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 1997년도 추계학술대회논문집; 한국과학기술회관; 6 Nov. 1997
• /
• pp.20-25
• /
• 1997

Magnetic bearings have been widely used to support rotors without any physical contact. This however, requires the control of five degrees-of-freedom and needs a separate driving motor. This paper introduces selfbearing motors which use the combination of a rotary motor and a magnetic bearing. These motors are suitable for use in high speed rotor or in special circumstances because they are small in size and can replace the contact components. The radial type one has the merit of being small in size and capable of controlling two degrees-of-freedom in x and y directions. The axial type motor controls only one degree-of-freedom in z direction. Theoretical background of the functions, of the motor and magnetic bearing will also be introduced. New research works are reviewed and the application in rotary blood pump is discussed.

• 한국자기학회지
• /
• 제5권5호
• /
• pp.695-701
• /
• 1995

Fundamental issues and general procedures of modeling the head disk interface (HDI) in order to provide design criteria for future ultra-low flying sliders are given. Intermittent contact and gaseous rarefaction effects are discussed using nonconventional kinetic theory. To illustrate the simulation results, we modeled IBM 3370 taper flat sliders and positive/negative "bow tie" sliders. Several alternative HDI concepts for future disk drives - viscoelastic bearings, a hybrid system, and contact recording - are also briefly discussed.

• 한국소음진동공학회논문집
• /
• 제13권3호
• /
• pp.172-179
• /
• 2003

Linear matrix Inequality based $H_\infty$ robust controller is designed to control the motion of a 4-axis unbalanced rigid asymmetric rotor supported and controlled by two active magnetic bearings in this paper. To this end, the equations of motion of the system are derived via Hamilton's variational principle and transformed to a state-space form for the standard $H_\infty$ control problem. LMI-based controller, which does not require additional assumptions beyond the usual stabilizability and detectability assumptions, is designed based upon the pole place weighting function and loopshaping technique. The obtained results are compared with those reported in the available literature and the efficiency of the proposed LMI-based $H_\infty$ control is revealed.