• Transactions of the Korean Society of Mechanical Engineers
• /
• v.9 no.1
• /
• pp.81-90
• /
• 1985

For the prediction of the real vibration and stability behaviour of rotor-beaing systems, various additional effects were considered, which are simplified or neglected by conventional modeling of real rotors. These are specially coupled spring and damping coefficients of journal bearings, spring and damping coefficients of external supporting elements for bearings, static load exerting on gears or pulleys by power transmissions, excitation through the gear tolerance or failure, and positive or negative spring and damping characteristics of magnetic or sealing friction force. Considering these effects, a computer program for the calculation of free and forced vibration of rotating shafts supported by two or more bearings is developed, based on the transfer matrixed method. The reliability of the calculated resutls were ascertianed by comparing with the measured data on high speed rotors supported by two journal bearings.

• Tribology and Lubricants
• /
• v.35 no.2
• /
• pp.114-122
• /
• 2019

High-speed rotating machinery requires low cost and reliable bearing elements with low friction, stable rotordynamic characteristics, and a simple design. This study experimentally evaluates the effects of bearing-support elements on the vibrational characteristics of a small-sized, high-speed permanent magnetic motor. A series of coast down tests from 100 krpm characterize the vibrational behaviors, rotor displacement, and housing acceleration of motors supported by ball bearings, ball bearings with a metal mesh damper, and gas foil bearings, respectively. Two eddy-current sensors installed in the horizontal and vertical directions measure the displacement of the rotor at its front nut, and a 3-axis accelerometer attached to the motor housing measures the housing acceleration. The test results reveal that synchronous (1X) vibration components most significantly affect the rotor displacement and housing acceleration, independent of the bearing-support elements. The motor supported by the deep-groove ball bearings results in the largest rotor vibrations increasing with speed; this is due to the absence of a damping mechanism. Additionally, the metal mesh damper effectively reduces the rotor displacement, housing acceleration, and sound-pressure level in the high-speed region (i.e., above 40 krpm), thus implying its substantial damping performance when installed on the outer race of the ball bearing. Lastly, the gas foil bearing supported motor yields the smallest rotor displacement, housing acceleration, and lowest sound-pressure level because of its hydrodynamic airborne operation, which does not require rolling elements that may cause mechanical friction and vibrations.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.16 no.12 s.117
• /
• pp.1201-1207
• /
• 2006

This paper introduces a step motor with a passively levitated rotor which comprises a homopolar step motor and a passive magnetic bearing. Compared with conventional self-bearing motors which are mostly based on the active magnetic bearing technology, the proposed motor has a very simple structure and operating principle. For the levitation, it works just like passive magnetic bearings which use the repulsive force between permanent magnets. Halbach array is used to increase the bearing stiffness. On the other hand, its rotation principle is just the same with that of conventional motors. In this paper, we introduce the design scheme to avoid the flux interference possibly produced by electromagnets and permanent magnets, and show some results of FEM analysis to predict the performance of the proposed motor.

• Journal of the Korean Society for Precision Engineering
• /
• v.13 no.10
• /
• pp.146-153
• /
• 1996

This paper presents the development of a collocated capacitance sensor and its application to the controller design for magnetic bearing supported rotor systems. The main feature of the sensor is that it is made of a compact printed circuit board(PCB) so that it can be built into the actuator coil of the magnetic bearing unit. The singnal processing unit hax been also developed. The experi- mental results of the sensor performance evaluation on sensitivity, bandwidth and resolution are presented. Then, simulation study shows the advantages of the collocated sensor for magnetic bearings over the nonco- llocated sensor. Finally, the experimental result on the performance of the collocated sensor based contrl- ler for a magnetic bearing rotor system is presented.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.22 no.10
• /
• pp.959-967
• /
• 2012

The theory for a new electromagnetically biased diskless combined radial and axial magnetic bearing is developed. A typical magnetic bearing system is composed of two radial magnetic bearings and an axial magnetic bearing. The axial magnetic bearing with a large axial disk usually limits rotor dynamic performance and makes assembling and disassembling difficult for maintenance work. This paper proposes a novel electromagnet biased integrated radial-axial magnetic bearing without axial disk. This integrated magnetic bearing uses two axial coils to provide the bias flux to the radial and axial air gaps of the combined bearing. The axial magnetic bearing unit in this combined magnetic bearing utilizes reluctance forces developed in the non-uniform air gaps such that the axial disk can be removed from the bearing unit. The 4-pole homopolar type radial magnetic bearing unit is also designed and analyzed. Three dimensional finite element model for the bearing is also developed and analyzed to illustrate the diskless combined magnetic bearing.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2001.05a
• /
• pp.948-953
• /
• 2001

Nonlinear dynamic equation of a 4-axis rigid rotor supported by two an-isotropic magnetic bearings is derived via Hamilton's principle. It is transformed to a state-space form for the standard Η$_{\infty}$ control problem. we present a robust Η$_{\infty}$ control design methods of continuous and discrete LMI-based approaches and improve performance using loopshaping.

• 제어로봇시스템학회:학술대회논문집
• /
• 1990.10b
• /
• pp.1178-1183
• /
• 1990

A digital signal processor(DSP) is applied to realizing a compensator of control system of active magnetic bearings, to restrict a resonance caused by the first-order bending vibration of a flexible rotor, and to run the rotor beyond the critical speed. A full-order observer is applied to the translatory rotor-motion with the first-order vibration mode. A PID control is used for the conical motion. The rotor used in the experiments is symmetric, and an electromagnet and a displacement sensor are set in collocation.

• Proceedings of the KIEE Conference
• /
• 2005.07b
• /
• pp.1171-1173
• /
• 2005

This paper presents a clean lifter design using a magnetic levitation system. Electromagnets are used as a levitation magnet attached to the clean lifter. The lateral forces are generated by the magnets so that non-contacting bearings are implemented. The clean lifter design specifications are suggested and the overall system is described.

• 한국초전도학회:학술대회논문집
• /
• v.15
• /
• pp.98-98
• /
• 2005

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2001.04a
• /
• pp.79-83
• /
• 2001

A cone-shaped active magnetic bearing spindle system for high speed internal grinding is designed and tested. The cone-shaped AMB system consists of only 4 couples of magnet, it can be smaller and lighter than conventional radial-axial-type AMB system. In this paper, the cone-shaped electromagnets are designed by magnetic circuit theory, and de-coupled direct feedback PID controller is applied to control the coupled magnetic bearings. The designed cone-shaped AMB spindle system is built and constructed with a digital control system, and tested its stbility and dynamic performances. As the results of the tests, this spindle runs up to 40,000 rpm with about 5 ${\mu}{\textrm}{m}$ of runout, and the AMB system provides high damping ratio eliminating overshoot and resonance speed.