• 전기학회논문지
• /
• 제65권5호
• /
• pp.769-772
• /
• 2016

In this paper, the overhang structure was applied to the axial flux permanent magnet (AFPM) motor. This paper describes the overhang effect in the AFPM motor. Moreover, the overhang effect was analyzed according to the different overhang length and an optimal overhang structure was proposed. Finally, the proposed structure was applied to design, analysis and experiment of prototype motors. Through the comparison between 3D finite element analysis results and experimental ones, the validity of proposed structure is clarified.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2006년도 추계학술대회 논문집 광주전남지부
• /
• pp.58-62
• /
• 2006

The purpose of this paper is characteristic analysis of permanent magnet generator (PMG) for automatic voltage regulator (AVR)power of brush less synchronous generator. However, this PMG has a spoke type permanent magnet rotor with large overhang for high power density, characteristic analysis considering concentration effect of air-gap flux density due to the overhang should be performed. 30 transient finite element method (FEM)analysis is good solution for overhang parameter, but this method needs too much calculation time. In this paper, we examined the overhang effects based on overhang length and material of rotor core by using 20 and 30 static FEM analysis, and proposed 20 dynamic FEA model considering overhang parameter which gives good and rapid results. The proposed method is verified by the test results of no load, load and short circuit test.

• 전기학회논문지
• /
• 제58권1호
• /
• pp.49-56
• /
• 2009

This paper shows the characteristic analysis of single-phase line start permanent magnet (LSPM) motors considering the overhang structure. To achieve the low-cost design of an LSPM motor, the overhang structure is adapted for the rotor with a constraint of a fixed magnet volume. To obtain the dynamic and steady performance of the motor, the circuit parameters are extracted using the 3D-static FEM(Finite Element Method) and the d-q equivalent circuit is used. The performance of the model with overhang is compared with the conventional model without overhang on the condition that both models have a fixed volume for the permanent magnet.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제55권10호
• /
• pp.505-510
• /
• 2006

This paper deals with skew and overhang effects of permanent magnet linear synchronous motor(PMLSM). The detent force and thrust characteristics considering skew and overhang effects of permanent magnet are analyzed by 3D finite element method and the results are compared to experimental values. As skew and overhang are applied to permanent magnet, the thrust is almost the same value but the detent force is reduced remarkably. By harmonic analysis, the distortion ratio of thrust is remarkably reduced from 4.29[%] to 2.3[%]. and, the ripple ratio of thrust is decreased from 8.2[%] to 3.56[%] at the same time. But, the lateral force which operate as the perpendicular direction of skew direction is generated. The lateral force and normal force acts by braking force between mover and LM-guide.

• 조명전기설비학회논문지
• /
• 제26권7호
• /
• pp.39-44
• /
• 2012

This paper deals with the characteristic analysis of small power brushless DC (BLDC) motor considering the rotor magnet overhang flux. In the driving characteristics analysis using 2D FEA (Finite Element Analysis), the rotor magnet overhang effect can't be considered and it should be neglected. To consider rotor magnet overhang effect, 3D FEA should be required. But 3D FEA requires very long calculation time even though the high specification computer is used. In this paper, the 3D electromagnetic model of BLDC motor is approximated as the 2D electromagnetic model considering overhang effect. In this paper, the concept of overhang coefficient is applied, and the coefficient according to load torque variance is deduced.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제55권7호
• /
• pp.346-352
• /
• 2006

In Brushless DC Motor, there are Permanent Magnets (PMs) with driving circuit and sensor for detecting to rotor position and rotation speed. In the case of using hall IC sensor which response to magnetic flux, that is required to additional sensor magnet for rotor position detecting. Most of BLDC motor, However, take asymmetrical overhang of PM in rotor instead of additional sensor magnet for operating of hall IC sensor. The asymmetrical overhang of PM occur rotor thrust to z-axis direction that is lead to not only damage of bearing but also intensive noise and vibration. Therefore, the analysis of magnet overhang effect in the side of vibration and drive to hall If sensor is required to precise. In this paper, 2-D Finite Element Method is used to solve precise field computation and thrust of z-axis direction considering asymmetrical magnet overhang. And also the z-axis thrust from the analysis result is compared to experimental result. In conclusion, the purpose of this paper minimize to noise and vibration of BLDC Motor as analyzes to asymmetrical magnet overhang effect.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제53권4호
• /
• pp.229-236
• /
• 2004

In this paper, the effect of permanent magnet overhang structure on the characteristics in Brushless DC motor has analyzed quantitatively. We classified the overhang structure as symmetric and asymmetric. 3D equivalent magnetic circuit network (EMCN) method which uses the permeance as the distributive variable is used for the efficient analysis of magnetic field. The overhang effect which increases the linkage flux at the stator is verified by comparison between overhang and no overhang structure. In addition, it is known that no load back electro motive force (EMF) is also increased due to the overhang effect. In case of asymmetric overhang structure, the ratio effect of the upper to lower overhang length on the magnetic forces is analyzed. Form the analysis results, the variation of the asymmetric overhang ratio has a significant effect on the axial magnetic force except the radial and tangential magnetic forces. The validity of the analysis results is also clarified by comparison between calculated results and measured ones such as back EMF and cogging torque.

• KIEE International Transaction on Electrical Machinery and Energy Conversion Systems
• /
• 제5B권2호
• /
• pp.123-128
• /
• 2005

This paper presents an analysis of the permanent magnet overhang effect for the permanent magnetic actuator. Generally, the overhang is often used to increase the force density in permanent magnet machineries. The overhang is particularly profitable in reducing the volume after increasing the force density per volume when using the overhang effect of the permanent magnet. Therefore, the 3D Equivalent Magnetic Circuit Network Method (3D EMCN) has been used in this paper. According to the plunger position, the flux distribution per overhang length and the holding force are quantitatively compared. Furthermore, an appropriate length of the overhang has been proposed. To confirm the accuracy of the analysis method, the results of 2D FEM and 3D FEM are compared for the basic model.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2003년도 하계학술대회 논문집 B
• /
• pp.918-920
• /
• 2003

This paper presents the analysis of the permanent magnet overhang effect for permanent magnetic actuator. Generally, The overhang is often used to increase the force density in permanent magnet machineries. The overhang is especially profitable to reduce the volume after increasing the force density per volume when using the overhang effect of the permanent magnet. Therefore, 3D Equivalent Magnetic Circuit Network Method (3D EMCNM) has been used in this paper. According to the plunger position, flux distribution per the overhang length, and the holding force are quantitatively compared. Furthermore, an appropriate length of the overhang has been proposed. To confirm the accuracy of the analysis method, the results of 3D EMCNM and FEM(2D, 3D) are compared for the basic model.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2007년도 추계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.80-82
• /
• 2007

This paper presents the overhang effects of a novel axial flux permanent magnet (AFPM) machine, which consist of the segmented stator and fractioned slot windings, with one rotor and double stator. In addition, the overhang effect of permanent magnet of the motor has been analyzed quantitatively. The overhang is used to enhance the force density in permanent magnet machine. According to the variation of overhang length, the flux density distribution and torque are quantitatively compared. For these analysis, three dimensional finite element method (3D FEM) has been used in this paper. From the results, the proper overhang length of PM is selected to improve the performance of the AFPM machine.