• 한국정밀공학회지
• /
• 제22권6호
• /
• pp.61-69
• /
• 2005

This paper presents the experimental results to analyze the atomization characteristics and environmental impact of cutting fluid in grinding process. Grinding is a major machining process to improve surface quality with different machining mechanism which is compared with turning or milling process. The environmental impact due to aerosol generation via grinding process is a major concern associated with environmental consciousness. Experimental results show that the generated fine aerosol which particle size less than 10 micron appears near working zone under given operational conditions. The aerosol concentration is much higher enough to affect human health risk with its generated aerosol quantities. This study can be provided a basic knowledge fur further research of environmental consciousness machining development.

• 한국정밀공학회지
• /
• 제21권9호
• /
• pp.196-203
• /
• 2004

SL(Stereolithography) part is made by piling up thin layers which causes the stair stepping effect at the surface of SL parts. The effect brings about excessive surface roughness and cuts down the merits of using SL part. Hence, additional post-machining finishing such as traditional grinding is required. But the traditional post-machining is detrimental to part geometry and time consuming. In this study, therefore, a paraffin coating and grinding post-machining is newly proposed to improve the surface quality of SL fart. The paraffin which has suitable properties for the proposed post-machining is coated all over the part surface. By grinding the only over-coated paraffin based on boundary of the SL part surface, the surface roughness can be improved without any damage on the part. Also, it is verified that SL part finished by the proposed post-machining process can be applied for rapid tooling as pattern through manufacturing silicon rubber molding and casting test.

• 한국공작기계학회논문집
• /
• 제14권2호
• /
• pp.55-61
• /
• 2005

The machining Parts must be Produced within the specification of drawing and those will be able to meet faction and efficiency. At that time, it is very important not only precision machine and machining technique but also the measurement technique. So, the improvement of measurement technique is to be joined together at once with improvement of machining technique. Finally, the quality and value of the parts are decided by precision measurement. This paper aims to study on the measurement uncertainty when the machined parts are inspected with 3-dimensional coordinate measuring machine. The objectives remove an error of measurement and remove a quality of mass products.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1995년도 추계학술대회 논문집
• /
• pp.165-168
• /
• 1995

The quality of products is depend on the performance of machine and machining conditions. In this study the runout of spindel is selected as a parameter through which we could appreciate the workability of machine and the quality of products. Throigh the runout of high speed machining center on freeload machining, the revolution accuracy and the characteristics in connection with spindle speed are evaluated. It was experimented flat and ball end milling for estimating machine accuracy and workability by measuring spindel runout. In end, This paper shows the effects of runout on surface roughness through analysis of runout and roughness profiles.

• 한국공작기계학회논문집
• /
• 제17권1호
• /
• pp.35-42
• /
• 2008

By the reason of increased demand of high productivity and quality, the manufacturer have an effort in many directions of a machine tool industries. Among there, we proposed method of decreasing displacement in MC(machining center). In other words, Quality related with vibration of a tool cutting products. For decreasing it, improved by optimizing a shape of the column-part and acceleration curves of motors. In this paper we could find design factors has much influence on decreasing the displacement using the DOE(Design of Experiments) and optimized the level of the factors using $ADAMS^{(R)}$ and $MINITAB.^{(R)}$ And we suggest optimized a acceleration curve using $Matlab^{(R)}$.

• 한국생산제조학회지
• /
• 제20권5호
• /
• pp.523-527
• /
• 2011

Polycarbonate (PC) polymer is an engineering plastic which has large tensile strength and impact resistance and is wildly used as functional parts like micro mold. Direct machining of PC materials produces lots of burrs and rough surface due to large ductility and weak heat resistance and hence it is very difficult to machine PC materials using cutting tool to make micro-parts. In this study, elliptical vibration cutting (EVC) or 2-dimensional vibration cutting was performed to minimize the size of micro V-grooves on PC material. From the experimental results, it was observed that as the cutting depth and pattern size become smaller, the better machining quality was obtained, which is attributed to the positive effect of EVC that is dependent on the ratio of vibration amplitude to cutting depth. As the height of V-groove becomes less than $1.8{\mu}m$, however, the machining quality becomes lower as the pattern size decreases.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 1999년도 추계학술대회 논문집 - 한국공작기계학회
• /
• pp.485-491
• /
• 1999

A burr is formed in every corner of parts as a result of machining, which produces undesirable edge geometry and influence deeply to surface quality of workpiece. Therefore these burrs must be removed certainly. The cost of removing these burrs is directly proportional to their size. Burrs have been among the most troublesome obstruction to high productivity and automation of machining processes. The proper selection of cutting condition and tool geometry will be helpful to reduce the occurrence of burrs. In paper will observe burr formation along helix angle in end milling and certificate experimentally mechanics relation of helix angle and burr formation.

• 한국정밀공학회지
• /
• 제17권12호
• /
• pp.68-75
• /
• 2000

This paper presents the construction of an ultra-precision machining system and machining experiments using the developed system. The system is composed of air bearing system, granite bed, air pad, and linear feeding mechanism. The cutting conditions have great effect on the surface quality in ultra-precision machining. the ultra-precision machining is mainly processed by several ${\mu}{\textrm}{m}$ depth of cut and feed rate. For this, tools with sharper cutting edge and less tool wear are needed. To satisfy these requirement, diamond is generally used as a tool material for ultra-precision machining. In order to evaluate the cutting characteristics of the PCD and MCD tools on the aluminum alloy, the machining experiments performed using the developed system.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 추계학술대회 논문집
• /
• pp.969-972
• /
• 1997

Ultrasonic machining technology has been developed over recent years for he manufacture of cost-effective and quality-assured precision parts for several industrial application such as optics, semiconductors, aerospace, and automobile application. The past decade has seen a tremendous in the use of ceramic in structural application. The excellent thermal, chemical and wear resistance of these material can be realized because of recent improvement in the overall strength and uniformity of advanced ceramics. Ultrasonic machining, in which abrasive particles in slurry with water are presented to the work surface in the presence of an ultrasonic-vibrating tool, is process which should be of considerable interest, as its potential is not limited by he electrical or chemical characteristics of the work material, making it suitable for application to ceramics. In order to improve the currently used ultrasonic machining using ultrasonic energy, technical accumulation is needed steadily through development of exciting device of ultrasonic machine composed of piezoelectric vibrator and horn. This paper intends to further the understanding of the basic mechanism of ultrasonic machining for brittle material and ultrasonic machining of ceramics based in the fracture-mechanic concept has been analyzed.

• 한국기계가공학회지
• /
• 제19권4호
• /
• pp.71-78
• /
• 2020

The rotary feed axes of a 5-axis machine tool can increase the freedom of the tool posture, while reducing feed speed and rigidity. In addition, as a ball-end mill is inevitably used during machining by rotational feed, the step-over length is reduced compared to the flat-end mill, thereby reducing the material removal rate. Therefore, this study attempts to improve the material removal rate, feed speed, and machining stability using the corner radius flat-end mill and a fixed controlled machining method for the rotary feed axes during roughing. In addition, the tapered ball-end mill and simultaneously controlled machining method for the rotary feed axes were used for finishing to improve the propeller's 5-axis machining efficiency by enhancing the surface quality. In order to create the tool path effectively and easily, we propose a specific approach for using the propeller's geometric properties and evaluate the effectiveness of the proposed method by comparing it with the method of the dedicated module.