• 한국정밀공학회지
• /
• 제20권5호
• /
• pp.22-28
• /
• 2003

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2010년도 추계학술대회 논문집
• /
• pp.121-122
• /
• 2010

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2010년도 춘계학술대회 논문집
• /
• pp.19-20
• /
• 2010

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1995년도 춘계학술대회 논문집
• /
• pp.3-20
• /
• 1995

Advanced ceramics have excellent thermal resistance, wear resistance, corrosion resistance, and other properties, and are promising materials as structural materials. Over the past decade, they have been applied to some machine parts, for example, glow plugs and turbochargers of automotive engines. In the case where the advanced ceramics are used as these structural parts, te low-dimensional accuracy of sintered bodies requires secondary machining.

• 한국기계가공학회지
• /
• 제1권1호
• /
• pp.38-47
• /
• 2002

Machining quality has been improved with the development of cutting tools. However, it is difficult to obtain a high degree of quality in machining a deep pocket with a long end mill, since machining accuracy is mainly dependent on the stiffness of the cutting tool and tool holder. To improve machining quality in machining a deep pocket using an end mill, the performance by cutting condition compare with others. Owing to this problem, it is necessary to select suitable tool and holder in the deep pocket machining. In this study, the hydraulic holder for the high speed machining is introduced and the performance of that is compared with others according to cutting conditions. The cutting parameters involved were; slenderness ratio in the range of 3 to 6 (L/D), radial depth of cut from 0.01 to 0.05 mm. Cutting force and surface roughness, precision of form were observed during the experiment to investigate cutting state.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2001년도 추계학술대회(한국공작기계학회)
• /
• pp.393-398
• /
• 2001

The technique of high speed machining is widely studied in machining fields, because the high efficiency and accuracy in machining can be obtained in high speed machining. Unfortunately the development of tool for high speed machining in not close behind that of machine tool. In this study, several types flat endmill is prepared for obtaining data according to tool shape. Especially, we concentrated in helix angle, number of cutting edge, rake angle and relief angle. Machinability is measured by cutting force, tool life, tool wear, chip shape and surface roughness according to cutting length. 3-axis cutting forces are acquired from the invented tool dynamometer for high speed machining. Particularly, we found out that the axial cutting force waveform has a good relation with tool wear features. By above results, it is suggested the endmill tool with $45^{\circ}$ helix angle, 6 cutting edge, $-15^{\circ}$ rake angle and $12^{\circ}$ relief angle be suitable for high speed machining

• 한국기계가공학회지
• /
• 제11권3호
• /
• pp.68-72
• /
• 2012

Al2017 is typical Duralumin of self-hardening aluminum alloy. It is lightweight, formability and machinability so throughout the industries have widely used automobile, electronics, semiconductor and aircraft as material. A variety of CNC machine tool processing technology, scientific principles and experience have been studied in order to increase accuracy and productivity. Using a machining center is to constant amount of side step and cutting characteristics studied changing depth of cut, revolution per minute and feed rate.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 1999년도 춘계학술대회 논문집
• /
• pp.251-255
• /
• 1999

In last paper, it was suggested electrochemical polishing method using the point electrode tools. It was aimed that Machining rate in ECM using the point electrode method should be ultimately small and also high dimension accuracy and surface integrity should be fine. In this paper, the machining characteristics were investigated by using the several types of electrolyte.

• 한국정밀공학회지
• /
• 제27권4호
• /
• pp.20-26
• /
• 2010

Any relative deformation between the cutting tool and the workpiece at the machining point, results directly in form and dimensional errors. The source of relative deformations between the cutting tool and the workpiece at the contact point may be due to thermal, weight, and cutting forces. This paper presents an investigation into dry and fluid machining with the objective of evaluating shape accuracy effect for the turning process of Al6061. The thermal distribution of cutting tool and cutting force was predicted using finite element method after measuring the temperature of the tool holder. To reach this goal, shape accuracy turning experiments are carried out according to cutting conditions with dry and fluid machining methods. The variable cutting conditions are cutting speed, depth of cutting and feed rate.

• 한국정밀공학회지
• /
• 제26권5호
• /
• pp.87-95
• /
• 2009

This research introduces the efficient modeling and manufacturing method using reverse engineering combined with rotational simulation of a pair of screw and mill-turn machining realized a proposed NC program. Because previously developed model had insufficient flow measuring accuracy, we considered that matter in the aspect of method of modeling and performance test. For that reason we modified the modeling which could minimize a gab between male and female screw, and developed precise tester which consists of constant tank, flowmeter and load cell, etc., and then conducted the test for defining characteristic and accuracy of flowmeter and repeated same test 5-times. Consequently we could obtain satisfied measuring accuracy and reproducibility indicated in the catalog of master model. Hence we give our conclusion as to the validity of developing accurate screw type flowmeter using the proposed process such as reverse engineering, mill-turn machining and precise performance test.