• Journal of the Korean Society for Precision Engineering
• /
• v.12 no.1
• /
• pp.87-96
• /
• 1995

A new fungivle material named Epoxy-Granite composite is applied to the column structure of drilling center in order to investigate the advanced dynamic charateristics comparing with a conventional cast iron material. The dimensions of new column structure are adjusted to keep the same stiffness (EI value) and the manufacturing conditions are formulated based on the preceeding research experience about the development of Epoxy-Granite structural material. The two kinds of experiments are set up, one of which is for the measurement of natural mode and frequency using experimental modal analysis, and the other one is for the measurement of vibration amplitude during idling operation of a machine tool. The comparison of maximum accelerance values at each natural frequency of bending mode shows a Epoxy-Granite column have larger modal damping ratios(over 2times) than a cast iron column. The vibration amplitude of Epoxy-Granite column measrued on the bed, motor base, and top of column are also much smaller (up to 12%) than the case of cast iron column. It is therefore confirmed that a Epoxy-Granite material exhibits a good anti- vibrational propderty even if it is used under the actual operational environments of machine tool as a practical structural element.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.21 no.6
• /
• pp.81-88
• /
• 2022

Titanium alloy (Ti-6Al-4V) has excellent mechanical properties and high specific strength; therefore, it is widely used in aerospace, automobile, defense, engine parts, and bio fields. Particularly in the aerospace field, as it has a low specific gravity and rigidity, it is used for the purpose of increasing energy efficiency through weight reduction of parts, and most have a thin-walled structure. However, it is extremely difficult to machine thin-walled shapes owing to vibration and deformation. In the case of thin-walled structures, the cutting forces and vibrations rapidly increase depending on the cutting conditions, significantly affecting the surface integrity and tool life. In this study, machining experiments on thin-wall milling of a titanium alloy (Ti-6Al-4V) were conducted for each experimental condition with different axial depths of cut, radial depth of cut, and machining sequence. The machining characteristics were analyzed, and an effective machining method was derived by a comprehensive analysis of the machined surface conditions and cutting signals.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.15 no.2
• /
• pp.51-56
• /
• 2016

High brittleness is a characteristic of glass, and in many cases it is broken during the process of machining due to processing problems, such as scratches, chipping, and notches. Machining defects occur due to the vibration of the equipment. Therefore, design techniques are needed that can control the vibration generated in the equipment to increase the strength of tempered glass. The natural frequency of the machine tool via vibration analysis (computer simulation) must be accurately understood to improve the design to ensure the stability of the machine. To accurately understand the natural frequency, 3D modeling, which is the same as actual apparatus, was used and a constraint condition was also applied that was the same as that of the actual apparatus. The maximum speeds of ultrasonic and high frequency, which are 15,000 rpm and 60,000 rpm, respectively, are considerably faster than those of typical machine tools. Therefore, an improved design is needed so that the natural frequency is formed at a lower region and the natural frequency does not increase through general design reinforcement. By restructuring the top frame of the glass processing, the natural frequency was not formed in the operating speed area with the improved design. The lower-order natural frequency is dominant for the effects that the natural frequency has on the vibration. Therefore, the design improvement in which the lower-order natural frequency is not formed in the operating speed area is an optimum design improvement. It is possible to effectively control the vibrations by avoiding resonance with simple design improvements.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.11 no.1
• /
• pp.31-37
• /
• 1991

Acoustic emission(AE) signals detected during metal cutting were applied as the experimental test to sensing tool wear and chipping on the NC vertical milling machine. The in-process detection of cutting tool wear including chipping, cracking and fracture has been investigated by means of AE in spite of vibration or noise through intermittent metal cutting, then the following results were obtained 1) When the tool wear is increased suddenly, or the amplitude of AE signals changes largely, it indicates chipping or breaking of the insert tip. 2) It was confirmed that AE signal is highly sensitive to the cutting speed and tool wear. 3) At the early period of cutting, the wear were large and RMS value increased highly by the influence of minute chipping and cracking, etc. Therefore, the above situations should be considered for the time when the tool would be changed.

• Journal of the Korean Society for Precision Engineering
• /
• v.7 no.1
• /
• pp.53-62
• /
• 1990

High speed and heavy cutting performed for improving the surface quality and productivity, are often prevented due to chatter phenomena. Chatter is a violent relative vibration between workpiece and tool in machining of metals, and is an important limiting factor of production rate and surface quality, and reduces the tool life and the dynamic performance of machine tool itself. In this study, in order to suppress the chatter, a modified tool-post combined with the spring and damper was designed and used in the actual cutting test. The results of this study are summerized as follows; The spring and damper adopted in the modified tool-post have the suppressing effects of chatter, and there exists an optimum combination between spring constant and damping ratio.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.20 no.8
• /
• pp.742-752
• /
• 2010

In case of the working machine that using in the loud-noisy workplace, as it generates the loud-noise, it is influencing a physical, mental bad effect to those workers. Accordingly, though the noise countermeasure for the loud-noisy workplace is acutely requiring, until now, those methods that wearing the soundproof-protection tool, or restriction the working hours, and minimize the noise exposure volume, were mainly used. However, such noise countermeasures occur many problem points. On such point of view, using the acoustic simulation technique, let the workers to choose the workplace where suffering many damages due to the noise of working machine, and after grasp the physical property of working machine and indoor acoustic characteristic, this Study has attempted to grasp the reduction degree of noise level at before-improvement?after-improvement, through the sound-absorption measure. Passing through such preceding step, using auralizational technique based on the noise of working machine of before-improvement after-improvement, and by conduct psycho-acoustics evaluation, this study intended to investigate the change degree of subject reaction. As the result of evaluation, it is considering that the noise-reduction countermeasure method for the loud-noisy workplace could be much effective, through the sound-absorption measure.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2004.04a
• /
• pp.88-92
• /
• 2004

We developed a helical type drum with an oblique cutting condition for sawdust machine. The existing drum has an orthogonal cutting(2D) condition considering of saw cutter and wood cutting pattern. Additional disadvantage of this type include big cutting resistance, high cost of cutting power and extreme occurrence of vibrations. To improve this shortcoming, we developed a helical type drum with an oblique cutting(3D) condition, therefore, this type drum decreased the vibration and cutting resistance of sawdust machine, and also improved productivity and sawdust porosity.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.14 no.1
• /
• pp.9-14
• /
• 2015

To build a high precision machine tool and increase its productivity, structural analysis needs to be carried out for vibration and stiffness of the machine tools before any detailed design. Therefore, in this paper, static and dynamic analysis is carried out to evaluate 8-axis multi tasking machining beds for automotive power train shafts; then, selection of an appropriate device is made for application to bed design. The results of structural and modal analysis confirmed the structural characteristics of the 8-axis multi tasking machine for automotive power train shaft beds: and the second shape bed is the safest is considered secure.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.12 no.6
• /
• pp.22-28
• /
• 2003

We should maintain the maximum operation capacity for production facilities and find properly out the fault of each equipment rapidly in order to decrease a loss caused by its failure. The acoustic signals of a machine always carry the dynamic information of the machine. These signals are very useful for the feature extraction and fault diagnosis. We performed a fundamental study which develops a system of fault diagnosis for a pump. We obtained noises by a microphone, analysed and compared the signals converted to Sequency range for normal products, artificially deformed products. We tried to search a change of noise signals according to machine malfunctions and analyse the type of deformation or failure. The results showed that acoustic signals as well as vibration signals can be used as a simple method for a detection of machine malfunction or fault diagnosis.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2001.04a
• /
• pp.309-314
• /
• 2001

The balance of high speed spindle system with high precision rotation like grinding machine is very important. Traditionally, we use trial and error method to balance the spindle. It takes much time. So we are developing the automatic balancing equipment being used in the grinding machine. The balancing head we develop is wireless. It will be used high-speed grinding machine. We use influence coefficient method to control the automatic balancer. Experiments are based on automatic and manual balancing. We perform test of the vibration filter. It helps to remove noise. The filter and experiments with automatic balancing controller show that automatic balancing control can be successfully achieved with the quick response and good stability characteristics.